SK E&C Civil Engineer Interview Questions and Answers

Q1. What was your previous salary what is your expect
Ans. 
I am unable to provide my previous salary as it is confidential. However, I am expecting a competitive salary based on my qualifications and experience.
• My previous salary is confidential and I am unable to disclose it.

• I am expecting a salary that is commensurate with my qualifications and experience.

• I am open to discussing salary expectations during the negotiation process.

• I believe that a competitive salary is importa...read more
Answered by AI
Add your answer
Q2. Previous salary 1 expected salary 2 whatever.
Add your answer
Q3. Educational mass card certificate documents previous salary certificate if you worked
Add your answer

Q1. Why are remove the pile head.
Ans. 
Pile heads are removed to allow for further construction or to ensure proper load transfer to the foundation.
• To prepare for further construction on top of the piles

• To ensure proper load transfer to the foundation

• To facilitate the installation of pile caps or beams

• To adjust the pile length if necessary
Answered by AI
Add your answer
Q2. How many deduction of 90 degree angle.
Ans. 
There are four deductions of 90 degree angles.
• A 90 degree angle is formed when two lines intersect at a right angle.

• In a square, all four angles are 90 degrees.

• In a rectangle, opposite angles are 90 degrees.

• In a right triangle, one angle is always 90 degrees.
Answered by AI
Add your answer
Q3. What is static load test and dynamic load test.
Ans. 
Static load test is used to measure the load capacity of a structure under a constant load, while dynamic load test is used to measure the response of a structure to varying loads.
• Static load test involves applying a constant load to a structure and measuring its response over time.

• Dynamic load test involves applying varying loads to a structure to simulate real-life conditions.

• Static load test helps determine the maxi...read more
Answered by AI
Add your answer
Q4. How many tolerance of pile load test.
Ans. 
The number of tolerance of pile load test depends on the specific project requirements and standards.
• The number of tolerance of pile load test can vary based on the project specifications and standards.

• Typically, a tolerance of +/- 5% to +/- 10% is considered acceptable for pile load tests.

• Some projects may have more stringent tolerance requirements depending on the criticality of the structure.

• It is important to refer...read more
Answered by AI
Add your answer
Q5. What is rang Density of bentonite and why is this use.
Ans. 
Bentonite has a range density of 17-22 lb/gal and is used in civil engineering for drilling fluid, grouting, and sealing purposes.
• Range density of bentonite is typically between 17-22 lb/gal.

• Bentonite is used in civil engineering for various purposes such as drilling fluid, grouting, and sealing.

• The range density of bentonite is important for determining its effectiveness in different applications.

• Higher range density ...read more
Answered by AI
Add your answer

Q1. Will ask Technical Questions Related to Projects.
Add your answer

Q1. Will ask about past companies experience and role, responsibility etc.
Add your answer

Q1. Foundation installation process is oil and gas industry
Ans. Explain it as required as per industry requirement like Valid Permit, Valid lifting plan, Approved method statement, barrication,Sign boards, banks man, competent and certified equipment and operator, rigger, color coded and inspected lifting accessories, check wind speed limits, foggy or dusty weather conditions
Answered Anonymously
Add your answer
Q2. Excavation process for oil and gas industry
Ans. 
Excavation process in the oil and gas industry involves several steps to ensure safe and efficient operations.
• The first step in the excavation process is to conduct a thorough site survey to identify potential hazards and determine the best approach for excavation.

• Before excavation begins, proper permits and approvals must be obtained from relevant authorities.

• Excavation equipment such as excavators, bulldozers, and ba...read more
Answered by AI
Add your answer
Q3. Valid Permit, approved method statement, Excavation certificate, check GPR (Ground penetrating radar)report, CAT (Cable avoidance Tool) Scan, Drawing, route marker, Trial pit, hard barricade the area, cert...read more
Add your answer

Q1. Procedure of laying tile and granite
Ans. 
The procedure of laying tile and granite involves preparing the surface, applying adhesive, laying the tiles/granite, grouting, and sealing.
• Prepare the surface by ensuring it is clean, level, and dry.

• Apply adhesive to the surface using a trowel, ensuring even coverage.

• Lay the tiles/granite starting from the center and working outwards in a pattern.

• Grout the tiles/granite by filling the gaps between them with grout and ...read more
Answered by AI
Add your answer

Q1. How many types of form work
Ans. 
There are several types of formwork used in construction.
• Formwork for columns

• Formwork for beams

• Formwork for slabs

• Formwork for walls

• Formwork for stairs

• Tunnel formwork

• Bridge formwork
Answered by AI
Add your answer
Q2. In cantilever beams tension force where occurs
Ans. 
Tension force occurs on the bottom of the cantilever beam.
• Tension force is caused by the bending moment in the beam.

• The bottom of the beam is in tension while the top is in compression.

• The location of maximum tension force depends on the loading and support conditions.

• Examples of cantilever beams include diving boards and balconies.
Answered by AI
Add your answer

Q1. Bbs, shuttering, leveling, testing, quality.
Add your answer

Q1. Hard work,.road line..pipe line.. others
Add your answer
Q2. Hard work.. road line..pipe line..others
Add your answer
Q3. Hard work..road line
Add your answer

Hard work and pipeline roadlines work...

Q1. Hard work..road line pipe line
Ans. 
All machine.(bom loader.jcb.oather) old pipe line area.. new pipe line coverage
Answered Anonymously
View 1 more answer
Q2. Hard work..road line pipe line work
Add your answer
Q3. Hard work..road line pipe line work ...
Add your answer
Q4. Hard work pipe line work
Add your answer

Hard work and pipeline roadlines work..

Q1. Hard work and pipeline roadlines
Add your answer
Q2. Hard work and pipeline ..roadlines
Add your answer
Q3. Hard work and pipeline roadlines work.
Add your answer
Q4. Hard work and pipeline roadlines work..
Add your answer
Q5. JCB work road line pipe..
Add your answer
Q6. Hard work and pipeline ..roadlines work..
View 1 more answer
Q7. Hard work.. pipe line work..
Add your answer
Q8. Hard work and pipeline roadlines ok
Add your answer
Q9. Civil foreman complete documents and..
Add your answer
Q10. Hard work and JCB work road line pipe line..
Add your answer
Q11. Road line pipe line.
Add your answer
Q12. Hard work pipe line pipe line
Add your answer
Q13. Hard work pipe line..
Add your answer
Q14. Hard work road line..
Add your answer
Q15. JCB work road line..
Add your answer

Hard work and pipeline roadlines work..

Hard work and pipeline roadlines