B. G. Shirke Construction Technology Assistant Engineer Interview Questions and Answers

Q1. Technical questions regarding our branch and field work
Add your answer

Q1. Regarding experience and salary discussion
Add your answer

Q1. Building structure
Add your answer

Q1. What has been your experience in your job?
Add your answer
Q2. What motivated you to leave your previous job, and what technical and execution experience do you possess?
Add your answer

Estimation of a small building.

Q1. Ratio of block work motor and plastrimg motor.
Ans. 
The ratio of block work motor to plastering motor is typically 1:3.
• The ratio of block work motor to plastering motor is usually 1:3.

• This means for every 1 part of block work motor, 3 parts of plastering motor are used.

• The ratio may vary depending on the specific project requirements.
Answered by AI
Add your answer
Q2. Per day productivity of a labour
Ans. 
The productivity of a laborer can be calculated by the amount of work completed in a day.
• Productivity is measured by the amount of work completed in a specific time frame, in this case, per day.

• Factors affecting productivity include skill level, motivation, tools/equipment available, and working conditions.

• Example: A construction worker completing 10 tasks in a day is more productive than one completing only 5 tasks.
Answered by AI
Add your answer
Q3. Amount of binding wire to be used per tone of reinforcement
Ans. 
Binding wire is typically used at a rate of 8-10 kg per ton of reinforcement.
• Typically, 8-10 kg of binding wire is used per ton of reinforcement to secure the bars in place.

• The amount of binding wire needed may vary based on the complexity of the reinforcement design and the spacing between bars.

• Using too little binding wire can result in inadequate reinforcement stability, while using too much can be wasteful and incr
Answered by AI
Add your answer
Q4. Density of materials
Ans. 
Density of materials is a measure of how much mass is contained in a given volume.
• Density is typically measured in units such as grams per cubic centimeter (g/cm^3) or kilograms per liter (kg/L).

• Materials with higher density have more mass packed into a given volume.

• Common examples of materials with high density include metals like lead and gold.

• Materials with low density include gases like helium and liquids like oil.
Answered by AI
Add your answer

Q1. Salary discussed
Add your answer

Q1. Bar Bending Schedule
Add your answer
Q2. Find out shuttering Area
Ans. 
Shuttering area can be calculated by finding the total surface area of the formwork used for concrete construction.
• Calculate the surface area of each individual formwork used for the concrete structure

• Add up the surface areas of all formworks to get the total shuttering area

• Consider any openings or gaps in the formwork when calculating the area
Answered by AI
Add your answer
Q3. Semi circle area formula
Ans. 
The formula for the area of a semi-circle is (1/2) * pi * r^2, where r is the radius of the semi-circle.
• The formula for the area of a semi-circle is (1/2) * pi * r^2

• The radius (r) is half the diameter of the circle

• Example: If the radius of a semi-circle is 5 cm, the area would be (1/2) * 3.14 * 5^2 = 39.25 cm^2
Answered by AI
Add your answer

Q1. Why u want to join this company ?
Add your answer
Q2. Why u want to quit Your present company
Add your answer
Q3. About my Salary
Add your answer

Q1. 1) different between diafraam wall and retaining wall
Ans. 
Diaphragm walls are used to create a barrier while retaining walls are used to hold back soil.
• Diaphragm walls are underground walls that are used to create a barrier to prevent water from entering a construction site.

• Retaining walls are used to hold back soil and prevent it from sliding or eroding.

• Diaphragm walls are typically made of reinforced concrete and are used in deep excavations.

• Retaining walls can be made of v...read more
Answered by AI
Add your answer
Q2. Which type of material used for shuttering
Ans. 
Plywood, steel, aluminum, and plastic are commonly used materials for shuttering.
• Plywood is the most commonly used material for shuttering due to its durability and affordability.

• Steel is used for heavy-duty construction projects as it can withstand high pressure and weight.

• Aluminum is lightweight and easy to handle, making it ideal for small-scale projects.

• Plastic is a cost-effective option for simple construction pro...read more
Answered by AI
Add your answer
Q3. Calculate the bbs of 4 by 3m footing, d = 300mm , dia of steel = 12mm
Ans. 
Calculate the bbs of a 4x3m footing with d=300mm and 12mm dia steel.
• Calculate the total length of steel required

• Determine the spacing between the bars

• Prepare a detailed bar bending schedule
Answered by AI
Add your answer
Q4. Hot to calculate the quantity of concrete for trapezoidal footing
Ans. 
To calculate the quantity of concrete for trapezoidal footing, we need to use the formula for volume of a trapezoidal prism.
• Measure the length, width, and height of the trapezoidal footing

• Calculate the area of the trapezoidal base using the formula (a+b)/2 * h

• Calculate the volume of the trapezoidal prism using the formula area of base * height

• Multiply the volume by the number of trapezoidal footings needed

• Add an additi
Answered by AI
Add your answer

About any road ways and types of bridges and classification of is codes for building construction

About any road ways and classification of turnouts.