i
Hi Tech Projects
Filter interviews by
Clear (1)
Minimum diameter of bar used in column is determined by structural requirements and load calculations.
Minimum diameter is typically specified in the structural design drawings or calculations
Factors such as column height, load capacity, and seismic considerations influence the minimum bar diameter
Common minimum diameters for column bars range from 12mm to 25mm depending on the structural requirements
Minimum grade of concrete used in column is typically M20.
Minimum grade of concrete used in column is usually M20
Higher grades like M25, M30, M35, etc. can also be used for columns based on structural requirements
The grade of concrete is determined based on the strength required for the structure
Minimum thickness of slab is determined based on factors like load, span, and material used.
Minimum thickness of slab is typically determined by structural engineers based on the expected loads and span of the slab.
Factors such as the material used for the slab and any additional reinforcement also play a role in determining the minimum thickness.
For example, a residential slab may have a minimum thickness of 4 inches,...
Water cement ratio is the ratio of the weight of water to the weight of cement used in a concrete mix.
Water cement ratio is a crucial factor in determining the strength and durability of concrete.
A lower water cement ratio results in stronger and more durable concrete.
The ideal water cement ratio varies depending on the type of concrete mix and its intended use.
For example, a typical water cement ratio for general purp
The density of steel is approximately 7.85 g/cm^3.
The density of steel is commonly expressed in grams per cubic centimeter (g/cm^3).
The density of steel can vary slightly depending on the specific alloy and composition.
For example, the density of stainless steel is around 7.9 g/cm^3, while carbon steel is around 7.85 g/cm^3.
Top trending discussions
I applied via Walk-in and was interviewed before Feb 2021. There were 5 interview rounds.
Consists of questions related to Aptitude and Reasoning
The GD round consists of group discussion on the topics given by interviewer
Regular aptitude questions from R.S. Aggarwal.
Some basic Programs and logics
Print star and string based
ArrayList is implemented using resizable array while LinkedList is implemented using doubly linked list.
ArrayList provides fast random access but slow insertion and deletion at middle. LinkedList provides fast insertion and deletion but slow random access.
ArrayList uses less memory overhead compared to LinkedList.
Example: ArrayList is suitable for scenarios where frequent access and less frequent insertion/deletion is ...
Print the tringle pattern and write the only logic
I applied via Company Website and was interviewed in Nov 2021. There were 4 interview rounds.
Two stock and four stock engines refer to the number of strokes in the engine cycle.
Two stock engine: Intake, compression, power, exhaust in two strokes
Four stock engine: Intake, compression, power, exhaust in four strokes
Two stock engines are simpler and lighter, but less efficient than four stock engines
Four stock engines are more common in modern vehicles due to better fuel efficiency and emissions control
I applied via Walk-in and was interviewed in May 2021. There were 4 interview rounds.
I applied via Naukri.com and was interviewed in Mar 2022. There were 2 interview rounds.
I applied via Company Website and was interviewed in Nov 2021. There were 3 interview rounds.
I applied via Recruitment Consulltant and was interviewed in Oct 2021. There were 2 interview rounds.
Python, c, c++, matlab
Python c, c++
based on 2 interviews
Interview experience
based on 3 reviews
Rating in categories
Planning & Billing Engineer
24
salaries
| ₹0 L/yr - ₹0 L/yr |
Safety Officer
22
salaries
| ₹0 L/yr - ₹0 L/yr |
Junior Engineer Civil
18
salaries
| ₹0 L/yr - ₹0 L/yr |
Junior Engineer
14
salaries
| ₹0 L/yr - ₹0 L/yr |
Assistant Engineer
12
salaries
| ₹0 L/yr - ₹0 L/yr |
Tech Mahindra
TCS
Infosys
Wipro