i
SHYAM METALICS AND ENERGY
Filter interviews by
Loco car & charging car axle change in breakdowns involves replacing damaged axles to ensure proper functioning of the vehicles.
Loco car axle change is necessary when the axle is damaged due to wear and tear or accidents.
Charging car axle change is required to maintain the stability and safety of the vehicle.
Proper maintenance and regular inspections can help prevent breakdowns related to axle issues.
Examples: Replacin...
I applied via campus placement at Jadavpur University and was interviewed in Feb 2024. There were 2 interview rounds.
Aptitude test was held by an online platform.
The second law of thermodynamics states that the total entropy of an isolated system can never decrease over time.
Entropy in a closed system tends to increase over time
Heat energy naturally flows from hot to cold objects
Efficiency of energy conversion processes is limited by the second law of thermodynamics
Creep is the slow, time-dependent deformation of a material under constant load, while fatigue is the weakening of a material due to repeated loading and unloading.
Creep is a time-dependent phenomenon, while fatigue is a cyclic phenomenon.
Creep occurs at high temperatures and constant stress, while fatigue occurs at lower temperatures and varying stress levels.
Creep leads to permanent deformation, while fatigue can lea...
A thermocouple is a temperature sensor that consists of two different metals joined together at one end, which produces a voltage proportional to the temperature difference between the junction and the other end.
Consists of two different metals joined together at one end
Produces a voltage proportional to the temperature difference
Commonly used in industrial applications for temperature measurement
T-t-t diagram is a time-temperature-transformation diagram used in materials science to understand the transformation of phases in a material.
T-t-t diagram shows the relationship between time, temperature, and the transformation of phases in a material.
It helps in predicting the microstructure of a material based on the cooling rate and temperature.
T-t-t diagrams are commonly used in metallurgy to understand the phase
Annealing is a heat treatment process used to soften metals and increase their ductility.
Annealing involves heating a metal to a specific temperature and then slowly cooling it to room temperature.
This process helps to relieve internal stresses, improve machinability, and enhance electrical conductivity.
Examples of metals that are commonly annealed include steel, copper, and aluminum.
The critical temperature of steel is the temperature at which it loses its magnetic properties.
The critical temperature of steel is around 770°C (1420°F).
Above this temperature, steel becomes non-magnetic and undergoes a phase change.
The critical temperature varies depending on the type of steel and its composition.
Types of steel include carbon steel, alloy steel, stainless steel, and tool steel. They can be differentiated based on their composition, properties, and applications.
Carbon steel contains primarily carbon and iron, with low amounts of other elements. It is commonly used in construction and manufacturing.
Alloy steel contains additional elements such as manganese, silicon, and copper to enhance its properties. It is use...
My name is John Smith.
Full name is John Smith
Common name in English-speaking countries
Easy to remember and pronounce
Seeking new challenges and growth opportunities in a dynamic work environment.
Looking for new challenges and opportunities for professional growth
Interested in working in a more dynamic and fast-paced environment
Seeking a role that aligns better with my career goals and aspirations
Carbon paste consumption in electrodes can be calculated by considering the weight of the paste used per electrode.
Calculate the weight of carbon paste used per electrode by measuring the initial and final weight of the electrode before and after use.
Divide the total weight of carbon paste used by the number of electrodes to get the average consumption per electrode.
Keep track of the consumption over time to monitor tr
Density is mass per unit volume of a substance.
Density = Mass / Volume
Units of density are typically g/cm^3 or kg/m^3
Density can be used to identify substances based on their mass and volume
Example: The density of water is approximately 1 g/cm^3
SHYAM METALICS AND ENERGY interview questions for popular designations
Get interview-ready with Top SHYAM METALICS AND ENERGY Interview Questions
MCC stands for Motor Control Center and PCC stands for Power Control Center. They are electrical panels used to control and distribute power to motors and other electrical equipment.
MCC panels are used to control and distribute power to motors in industrial settings.
PCC panels are used to control and distribute power to various electrical equipment.
Both panels play a crucial role in ensuring efficient and safe operatio...
The best steel plant is often determined by factors such as production capacity, technology used, quality of output, and efficiency.
Consider the production capacity of the plant - higher capacity usually indicates a better plant
Look at the technology used - modern and advanced technology can lead to better quality output
Evaluate the quality of the steel produced - consistent high-quality output is a sign of a good plan...
The best steel for a specific application depends on factors such as strength, corrosion resistance, and cost.
The best steel for construction may be different from the best steel for cutlery or automotive parts
Factors to consider include strength, corrosion resistance, machinability, and cost
Examples of popular steel types include stainless steel, carbon steel, and tool steel
I applied via LinkedIn and was interviewed in Oct 2023. There were 2 interview rounds.
An induction motor is a type of AC motor where power is supplied to the rotor by electromagnetic induction.
Induction motors are commonly used in various applications such as industrial machinery, pumps, fans, and compressors.
They do not require brushes to transfer power to the rotor, making them more reliable and maintenance-free compared to brushed DC motors.
The speed of an induction motor is determined by the frequen...
A DC series motor is a type of DC motor where the field winding is connected in series with the armature winding.
Field winding and armature winding are connected in series
High starting torque but low speed
Used in applications where high starting torque is required, such as in traction applications
I applied via campus placement at Jadavpur University and was interviewed in Mar 2024. There were 2 interview rounds.
Genral science, maths, puzzles
Top trending discussions
The duration of SHYAM METALICS AND ENERGY interview process can vary, but typically it takes about less than 2 weeks to complete.
based on 112 interviews
Interview experience
based on 889 reviews
Rating in categories
Engineer
206
salaries
| ₹2.1 L/yr - ₹6.1 L/yr |
Assistant Engineer
190
salaries
| ₹1.5 L/yr - ₹4.2 L/yr |
Assistant Manager
163
salaries
| ₹3.5 L/yr - ₹9 L/yr |
Senior Engineer
158
salaries
| ₹3.3 L/yr - ₹8.2 L/yr |
Mechanical Engineer
71
salaries
| ₹2 L/yr - ₹5.8 L/yr |
Tata Steel
JSW Steel
Steel Authority Of India
Jindal Steel and Power