Larsen & Toubro Limited B Tech Civil Engineer Interview Questions and Answers

Two ships are sailing in the sea on the two sides of a lighthouse. The angle of elevation of the top of the lighthouse is observed from the ships are 30° and 45° respectively. If the lighthouse is 100 m high, the distance between the two ships is:
173 m
200 m
273 m
300 m

Q1. Who is in my house? Am I willing to go out of West Bengal if I get a job out of West Bengal?
Add your answer

Q1. Which lime is used for white washing
Ans. 
Quicklime is used for white washing.
• Quicklime, also known as calcium oxide, is used for white washing.

• It is a white, caustic, alkaline substance that is produced by heating limestone in a kiln.

• When water is added to quicklime, it undergoes a chemical reaction to form calcium hydroxide, which is used in white washing.
Answered by AI
Add your answer

Very basic level aptitude test and civil engineering subjects test.

Q1. Draw bending moment diagram of a fixed beam subjected to udl throughout the whole length.
Ans. 
Bending moment diagram of a fixed beam subjected to udl throughout the whole length.
• Calculate the reactions at the supports of the beam

• Determine the equation for bending moment at any point along the beam

• Plot the bending moment diagram with positive and negative values

• The bending moment will be maximum at the supports and zero at the midpoint of the beam
Answered by AI
Add your answer
Q2. Draw bending moment diagram of a 1-bay, 1-storey portal frame subjected to point load at the middle point of the column.
Ans. 
Bending moment diagram of a 1-bay, 1-storey portal frame with point load at column middle.
• Calculate reactions at supports

• Determine internal forces at critical points

• Plot bending moment diagram using equations or software

• Identify maximum bending moment and its location
Answered by AI
Add your answer
Q3. What is 'M' in M-20 concrete?
Ans. 
M stands for mix design in M-20 concrete, indicating the compressive strength of the concrete mix.
• M-20 concrete is a mix design where 'M' represents the compressive strength of the concrete after 28 days of curing.

• The number '20' in M-20 concrete indicates the characteristic compressive strength of concrete in N/mm^2.

• Different grades of concrete have different compressive strength requirements, with M-20 being a common
Answered by AI
Add your answer
Q4. Which code is req for mix design?
Ans. 
IS 10262 is required for mix design in civil engineering.
• IS 10262 is the code for concrete mix design in India.

• It provides guidelines for proportioning of concrete ingredients based on strength and durability requirements.

• The code covers various aspects such as water-cement ratio, workability, and compressive strength.

• Mix design is crucial for ensuring the desired properties and performance of concrete.

• Following the co...read more
Answered by AI
Add your answer
Q5. What is the process of earthquake design of a multi storey building?
Ans. 
Earthquake design of a multi storey building involves analyzing seismic forces, selecting appropriate structural systems, and implementing design measures to ensure safety.
• Analyze seismic forces based on the building location and seismic zone

• Select appropriate structural systems such as reinforced concrete or steel frames

• Implement design measures like base isolation, dampers, and shear walls to enhance building's seism
Answered by AI
Add your answer
Q6. Process of design of one-way and two-way slab and their differences
Ans. 
Design process of one-way and two-way slabs and their differences
• One-way slab design involves calculating bending moments and shear forces along one direction, typically supported on two opposite sides. Two-way slab design considers bending moments and shear forces in both directions, usually supported on all four sides.

• One-way slab design is simpler and more common in practice, while two-way slab design is more comple...read more
Answered by AI
Add your answer
Q7. Difference between dynamic and equivalent static method of earthquake design and analysis of multi storey building
Ans. 
Dynamic method considers time history of earthquake while equivalent static method simplifies earthquake forces into equivalent static forces.
• Dynamic method analyzes building response to actual time history of earthquake ground motion.

• Equivalent static method simplifies earthquake forces into equivalent static forces based on simplified assumptions.

• Dynamic method is more accurate but computationally intensive, while eq...read more
Answered by AI
Add your answer

Q1. About civil engineer
Add your answer