AmbitionBox
Interview Questions
- Reviews
- Salaries
- Interview Questions
- About Company
- Benefits
- Jobs
- Office Photos
- Community
Add office photos
Filter interviews by
Havells Design Engineer Interview Questions, Process, and Tips for Experienced
Havells Design Engineer Interview Experiences for Experienced
1 interview found
Anonymous
I applied via Recruitment Consulltant and was interviewed in Apr 2023. There were 3 interview rounds.
(4 Questions)
- Q1. Plastic shrinkage?
- Q2. How many types of plastic material category?
- Ans.
There are seven main categories of plastic materials.
Thermoplastics
Thermosets
Elastomers
Composites
Biodegradable plastics
Engineering plastics
High-performance plastics
- Q3. Plastic rib thickness standard?
- Ans.
Plastic rib thickness standard varies depending on the application and material used.
Plastic rib thickness is typically between 0.5mm to 5mm.
Thicker ribs provide more strength but may increase material usage and cost.
Thinner ribs are more cost-effective but may be prone to warping or breaking.
Consider the material properties and intended use when determining rib thickness.
Consult industry standards and guidelines for s
- Q4. How many types of defects in plastic?
- Ans.
There are three main types of defects in plastic: surface defects, physical defects, and chemical defects.
Surface defects include scratches, sink marks, and flow marks.
Physical defects include bubbles, voids, and warping.
Chemical defects include discoloration, degradation, and contamination.
(7 Questions)
- Q1. Diff b/w hot runner & cold runner?
- Q2. How to prevent plastic defects?
- Ans.
Preventing plastic defects involves proper material selection, design optimization, and quality control measures.
Selecting the right type of plastic for the application
Optimizing the design to minimize stress concentrations
Implementing proper molding techniques and parameters
Conducting thorough quality control inspections
Training staff on proper handling and storage of plastic materials
- Q3. No. of tonnage molding machine you are used?
- Ans.
I have experience working with various tonnage molding machines, including 50-ton, 100-ton, and 200-ton machines.
50-ton molding machine
100-ton molding machine
200-ton molding machine
- Q4. What is draft angle in plastic?
- Ans.
Draft angle in plastic is the degree of taper or slope applied to the vertical walls of a plastic part to facilitate its ejection from the mold.
Draft angles are typically recommended to be between 1-3 degrees for most plastic parts
Draft angles help prevent the part from getting stuck in the mold during ejection
Examples of draft angles include adding a slight taper to the sides of a plastic cup or the walls of a plastic
- Q5. What is parametric modelling?
- Ans.
Parametric modelling is a design approach where the model is defined by a set of parameters and rules that govern its shape and size.
Uses parameters to define the shape and size of the model
Allows for easy modification of the design by changing parameters
Enables creation of complex designs with interconnected features
Commonly used in CAD software like SolidWorks and Autodesk Inventor
- Q6. How to solve plastic defects issue in plastic?
- Ans.
Plastic defects can be solved by identifying root causes, adjusting processing parameters, using quality materials, and implementing proper maintenance.
Identify root causes of defects such as improper molding conditions or poor material quality
Adjust processing parameters like temperature, pressure, and cooling rate to optimize production
Use high-quality materials to ensure consistency and durability of the final produ...
- Q7. Cad test on NX Software 2306 version? Plastic parts devlop in cad softwares?
- Ans.
Yes, CAD tests can be conducted on NX Software 2306 version. Plastic parts can be developed in CAD software.
CAD tests can be performed on NX Software 2306 version to ensure compatibility and functionality.
CAD software allows for the design and development of plastic parts with precision and accuracy.
Features like 3D modeling, simulation, and analysis tools in CAD software aid in the development of plastic parts.
Example...
Interview Preparation Tips
- Product Design
- Injection Moulding
- UG NX
Skills evaluated in this interview
Top trending discussions
Interview questions from similar companies
Senior Engineer Interview Questions & Answers
CG Power and Industrial Solutions
posted on 24 Apr 2021
I applied via Naukri.com and was interviewed before Apr 2020. There were 3 interview rounds.
Interview Questionnaire
2 Questions
- Q1. About circuit breaker, transformer.
- Q2. Single line diagrams, layout, substation calculation.
Interview Preparation Tips
I applied via Company Website and was interviewed in Jul 2021. There were 3 interview rounds.
(1 Question)
- Q1. Tell me about yourself.
Interview Preparation Tips
Selected
I appeared for an interview in Dec 2022.
(6 Questions)
- Q1. How do u configure switch?
- Ans.
Switch configuration involves setting up VLANs, port security, QoS, and other settings to optimize network performance.
Access the switch's command line interface (CLI) using a console cable or remote access software
Configure VLANs to segment network traffic and improve security
Enable port security to prevent unauthorized access to the network
Set up Quality of Service (QoS) to prioritize network traffic and ensure criti...
- Q2. What is L2 and L3 Switch and it's differences
- Ans.
L2 and L3 switches are network devices used for packet switching. L2 operates at the data link layer and L3 at the network layer.
L2 switch operates at the data link layer and forwards packets based on MAC addresses
L3 switch operates at the network layer and forwards packets based on IP addresses
L2 switch is used for LAN networks while L3 switch is used for both LAN and WAN networks
L2 switch is faster than L3 switch as ...
- Q3. What is MPLS, where it is used
- Ans.
MPLS is a protocol used for efficient packet forwarding in a network. It is used in WANs and service provider networks.
MPLS stands for Multiprotocol Label Switching
It is used to improve the speed and efficiency of network traffic routing
MPLS uses labels to identify the path that packets should take through the network
It is commonly used in WANs and service provider networks to provide Quality of Service (QoS) and traff...
- Q4. Explain about VLANS and how do we create
- Ans.
VLANs are virtual LANs that allow network administrators to group devices together based on their functions or departments.
VLANs are used to segment a network into smaller, more manageable groups.
They can be created using network switches or routers.
Each VLAN has its own broadcast domain and can be configured with its own security policies.
VLANs can be created based on different criteria such as department, location, o...
- Q5. Why do we get hired
- Q6. What do u know about the company
Interview Preparation Tips
Skills evaluated in this interview
(3 Questions)
- Q1. Basic knowledge
- Q2. Switchgear knowledge
- Q3. Marketing knowledge
Interview Preparation Tips
I applied via Recruitment Consultant and was interviewed in Dec 2021. There was 1 interview round.
Interview Questionnaire
1 Question
- Q1. All the questions were related to job profile.
Interview Preparation Tips
Selected
I applied via Recruitment Consulltant and was interviewed in Nov 2022. There was 1 interview round.
(2 Questions)
- Q1. What you done best practice in existing company?
- Ans.
Implemented best practices in software development lifecycle, including code reviews and automated testing.
Introduced code reviews to ensure code quality and consistency
Implemented automated testing to catch bugs early in the development process
Utilized version control system effectively to track changes and collaborate with team members
- Q2. What you done best practice in previous years?
Senior Engineer Interview Questions & Answers
HBL Power Systems
JAGDHAN VIJAY KUMAR
posted on 16 Dec 2023
Selected
I applied via Naukri.com and was interviewed before Dec 2022. There were 4 interview rounds.
(1 Question)
- Q1. Basic questions regarding ur interest and profile, experience
(3 Questions)
- Q1. Technical interview as well Written Test will be here,
- Q2. All basic Networking questions will be asked
- Q3. Knowledge on networking design will be the advantage with Auto cad
(1 Question)
- Q1. Network Basics, Switching and Routing
Interview Preparation Tips
I applied via Company Website and was interviewed in Jan 2022. There were 2 interview rounds.
(2 Questions)
- Q1. Tell me about yourself.
- Q2. Notice period of my present organisation
(1 Question)
- Q1. Site based question about TG Deck Slab, Ash Handling Package
Interview Preparation Tips
Selected
I applied via Campus Placement and was interviewed before Feb 2023. There were 2 interview rounds.
Basic math and quantitative aptitude related questions
(2 Questions)
- Q1. Tell me about thecompany
- Ans.
The company is a leading technology firm specializing in software development and engineering solutions.
Founded in 2005 by a group of software engineers
Provides services in web development, mobile app development, and cloud computing
Clients include Fortune 500 companies such as Google and Microsoft
- Q2. How will you solve a critical problem coming to you as a engineer
Havells Interview FAQs
Tell us how to improve this page.
Havells Interviews By Designations
- Havells Assistant Manager Interview Questions
- Havells Deputy Manager Interview Questions
- Havells Rural Sales Officer Interview Questions
- Havells Senior Engineer Interview Questions
- Havells Production Engineer Interview Questions
- Havells Manager Interview Questions
- Havells Senior Sales Executive Interview Questions
- Havells Sales Officer Interview Questions
- Show more
Interview Questions for Popular Designations
- Mechanical Engg. Design Interview Questions
- Senior Design Engineer Interview Questions
- Electrical Design Engineer Interview Questions
- Structural Design Engineer Interview Questions
- Piping Designer Interview Questions
- Auto CAD Designer Interview Questions
- Junior Design Engineer Interview Questions
- Hardware Design Engineer Interview Questions
- Show more
Havells Design Engineer Interview Process for Experienced
based on 1 interview
Interview experience
Design Engineer Interview Questions from Similar Companies
Fast track your campus placements
Havells Design Engineer Reviews and Ratings
based on 15 reviews
Rating in categories
|
Assistant Manager
916
salaries
|  ₹5 L/yr - ₹15.5 L/yr |
|
Deputy Manager
656
salaries
| ₹7.3 L/yr - ₹18.8 L/yr |
|
Manager
575
salaries
| ₹7.9 L/yr - ₹25 L/yr |
|
Senior Engineer
404
salaries
| ₹3.3 L/yr - ₹12.5 L/yr |
|
Senior Manager
345
salaries
| ₹11.5 L/yr - ₹31.6 L/yr |
CG Power and Industrial Solutions
C&S Electric
KEI Industries
Finolex Cables
- Home >
- Interviews >
- Havells Interview Questions >
- Havells Design Engineer Interview Questions for Experienced
