TCE Senior Manager Design Interview Questions and Answers

Aptitude test was not prompt

Q1. They mentioned personal interview for technical round
Add your answer
Q2. They took technical interview and then gave detailing work.
Add your answer

Q1. Hr is very poor
Add your answer

Q1. Stress, strain, thermodynamics
Add your answer
Q2. Degree of freedom, Pressure
Ans. 
Degree of freedom refers to the number of independent variables that can be changed in a system, while pressure is the force exerted on a surface per unit area.
• Degree of freedom in product design refers to the number of ways a component can move or be adjusted independently.

• Pressure in product design is important for determining the strength and stability of materials and structures.

• Understanding the degree of freedom ...read more
Answered by AI
Add your answer
Q3. Ohm's law, laws of thermodynamics
Add your answer
Q4. Basics of SOM, GD&T
Add your answer

Q1. About JOB ROLE explanination
Add your answer
Q2. About the design process
Add your answer

Basic aptitude and reasoning

GD about some general topic

Q1. Spt test, admixture types
Add your answer
Q2. Basic of soil mechanics, rcc
Add your answer
Q3. What is spt ?
Ans. 
SPT stands for Standard Penetration Test, a common in-situ test to determine the relative density of granular soils.
• SPT involves driving a split-spoon sampler into the ground using a hammer and counting the number of blows required to penetrate the soil a certain depth.

• The results of the SPT test are used to assess the soil's strength and stiffness properties for geotechnical engineering purposes.

• SPT values are typical...read more
Answered by AI
Add your answer
Q4. Types of admixture and mix
Ans. 
Admixtures are materials added to concrete to enhance its properties, while mix refers to the combination of ingredients in concrete.
• Admixtures include water-reducing admixtures, air-entraining admixtures, accelerating admixtures, and retarding admixtures.

• Mix refers to the combination of cement, water, aggregates, and admixtures in concrete.

• Examples of admixtures are plasticizers, superplasticizers, accelerators like c...read more
Answered by AI
Add your answer

Q1. How many methods are used to forecast population
Ans. 
There are multiple methods used to forecast population.
• Demographic analysis

• Cohort-component method

• Time series analysis

• Mathematical models

• Survival analysis

• Migration analysis
Answered by AI
View 2 more amswers
Q2. How to calculate ESR capacity
Ans. 
ESR capacity can be calculated by measuring the equivalent series resistance (ESR) of a component or circuit.
• ESR capacity is determined by measuring the ESR of the component or circuit.

• ESR is the resistance that exists in series with the ideal capacitance of a component.

• To calculate ESR capacity, use an ESR meter or measure the voltage drop across a known current.

• ESR capacity is important in determining the performance...read more
Answered by AI
View 1 more amswer
Q3. What is the peak factor are used for Distribution design
Ans. 
Peak factors are used in distribution design to account for peak loads and ensure safe and efficient operation.
• Peak factors are used to determine the maximum load that a distribution system can handle.

• They take into consideration factors such as diversity of loads, power factor, and future growth.

• For example, a peak factor of 1.5 means that the system should be designed to handle 50% more than the average load.

• Peak fac...read more
Answered by AI
View 1 more amswer
Q4. What is the minimum residual pressure in SVS
Ans. 
The minimum residual pressure in SVS refers to the lowest pressure that remains in the system after it has been depressurized.
• The minimum residual pressure is important to ensure the system is properly depressurized and safe for maintenance or repair.

• It is typically measured in units of pressure, such as psi or bar.

• The specific value of the minimum residual pressure can vary depending on the design and requirements of ...read more
Answered by AI
View 1 more amswer
Q5. What is the Component in the water supply scheme
Ans. 
Components in a water supply scheme include pipes, pumps, valves, storage tanks, and treatment facilities.
• Pipes: Used to transport water from the source to the distribution network.

• Pumps: Provide the necessary pressure to move water through the system.

• Valves: Control the flow and direction of water within the scheme.

• Storage tanks: Store water for peak demand periods or emergencies.

• Treatment facilities: Purify and disin
Answered by AI
View 1 more amswer
Q6. For Distribution system and Headwork what is the design period
Ans. 
The design period for distribution system and headwork refers to the expected lifespan or duration for which the system is designed to function effectively.
• The design period is determined based on factors such as expected growth, technological advancements, and maintenance requirements.

• It is important to consider the long-term needs and goals of the distribution system and headwork when determining the design period.

• Fo...read more
Answered by AI
View 1 more amswer
Q7. For Design Pumping machinery and ESR what is the design period.
Ans. 
The design period for pumping machinery and ESR refers to the intended lifespan or duration of operation for the equipment.
• The design period is typically determined based on factors such as expected usage, maintenance requirements, and technological advancements.

• It is important to consider the design period when selecting materials, components, and manufacturing processes to ensure durability and reliability.

• For exampl...read more
Answered by AI
View 1 more amswer

Campus selection - reasoning tests

Q1. Question answers like iron carbon diagram..
Add your answer
Q2. Questions from material handling.
Add your answer