Upload Button Icon Add office photos

Microtek International

Compare button icon Compare button icon Compare

Filter interviews by

Clear (1)

Microtek International Design Engineer Interview Questions, Process, and Tips

Updated 22 Feb 2024

Microtek International Design Engineer Interview Experiences

1 interview found

Design Engineer Interview Questions & Answers

user image vivian vincent

posted on 22 Feb 2024

Interview experience
1
Bad
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Approached by Company and was interviewed before Feb 2023. There was 1 interview round.

Round 1 - Technical 

(5 Questions)

  • Q1. Tell us about your Project
  • Q2. Tell the difference between MOSFET and IGBT
  • Ans. 

    MOSFET is faster and more efficient for high frequency applications, while IGBT is better for high voltage and high current applications.

    • MOSFET stands for Metal-Oxide-Semiconductor Field-Effect Transistor, while IGBT stands for Insulated Gate Bipolar Transistor.

    • MOSFET is faster and more efficient for high frequency applications, while IGBT is better for high voltage and high current applications.

    • MOSFET has lower on-sta...

  • Answered by AI
  • Q3. Tell the principal of Sine wave inverter
  • Ans. 

    A sine wave inverter is a type of power inverter that produces a smooth and consistent AC output waveform similar to that of utility power.

    • Sine wave inverters are preferred for sensitive electronics as they provide clean power without distortion.

    • They are more efficient and produce less audible noise compared to modified sine wave inverters.

    • Examples of devices that benefit from sine wave inverters include laptops, TVs,

  • Answered by AI
  • Q4. What is CMOS Latchup
  • Ans. 

    CMOS latchup is a phenomenon in integrated circuits where parasitic thyristors are inadvertently triggered, causing a short circuit.

    • CMOS latchup occurs when a parasitic structure in the CMOS device acts as a thyristor, leading to a low-impedance path between the power supply rails.

    • It can result in excessive current flow, potentially damaging the device.

    • Preventive measures include layout techniques, guard rings, and pro...

  • Answered by AI
  • Q5. How to Design an inductor
  • Ans. 

    Designing an inductor involves determining the required inductance value, selecting the core material, calculating the number of turns, and designing the coil structure.

    • Determine the required inductance value based on the application requirements.

    • Select the appropriate core material based on factors such as frequency, current, and temperature.

    • Calculate the number of turns using the formula N = sqrt((L * AL) / (Ae * Nt)...

  • Answered by AI

Interview questions from similar companies

I applied via Recruitment Consulltant and was interviewed before May 2021. There was 1 interview round.

Round 1 - Technical 

(1 Question)

  • Q1. Position Tolerance, Tolerance stack, Temperature Rise test, Vaccuum Circuit breaker, arc quenching,

Interview Preparation Tips

Interview preparation tips for other job seekers - Time taking process 2 month almost
Position goes on hold sometimes
They are more happy taking diversity candidates

I applied via Campus Placement and was interviewed before Apr 2019. There was 1 interview round.

Interview Questionnaire 

4 Questions

  • Q1. What is your key achievement ? Either your study or professional
  • Q2. What you think about company ?
  • Q3. Where you see yourself in company ?
  • Q4. Why we select you?

Interview Preparation Tips

Interview preparation tips for other job seekers - Don't panic or hesitate or stress
Opportunities never ends

Interview Questionnaire 

3 Questions

  • Q1. What is FMEA and CP,CPK
  • Ans. 

    FMEA is a risk assessment tool used to identify and mitigate potential failures. CP and CPK are statistical measures of process capability.

    • FMEA stands for Failure Mode and Effects Analysis

    • It is used to identify potential failures in a process or product

    • CP and CPK are statistical measures of process capability

    • They are used to determine if a process is capable of producing products within specification limits

    • CPK is a mor...

  • Answered by AI
  • Q2. What is your ambitions
  • Q3. How can grow a industry in QMS
  • Ans. 

    Industry growth in QMS can be achieved by implementing efficient quality management systems and promoting their benefits.

    • Developing and implementing effective QMS policies and procedures

    • Providing training and education to employees on QMS

    • Encouraging continuous improvement and innovation in QMS

    • Promoting the benefits of QMS to customers and stakeholders

    • Ensuring compliance with industry standards and regulations

    • Collaborat...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Be aware and give idea of every concern.

I applied via Naukri.com and was interviewed in Oct 2021. There were 4 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all Resume tips
Round 2 - Technical 

(1 Question)

  • Q1. All Questions are about my previous experience and work role & responsibility
Round 3 - Technical 

(1 Question)

  • Q1. All question are about power electronics and IGBT, MOSFET Gate drive etc.
Round 4 - One-on-one 

(1 Question)

  • Q1. About salary discussion

Interview Preparation Tips

Interview preparation tips for other job seekers - Just only givi
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all Resume tips
Round 2 - Technical 

(1 Question)

  • Q1. Regards lithium ion battery what is soc what is soh pre-charge cell chemistry
  • Ans. 

    SOC refers to the state of charge of a battery, SOH refers to the state of health, pre-charge is the initial charging process, and cell chemistry refers to the type of chemicals used in the battery.

    • SOC is the amount of charge remaining in a battery, expressed as a percentage of its maximum capacity.

    • SOH is a measure of a battery's overall health and its ability to hold a charge over time.

    • Pre-charge is the initial chargi...

  • Answered by AI
Round 3 - HR 

(1 Question)

  • Q1. Last company related why are you join this organization'' what are your job responsibilities in last company?

Interview Preparation Tips

Interview preparation tips for other job seekers - nothing no just focus on your last compoany profile what are you doing in last comaopny your major challenges face in last companinies
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Approached by Company and was interviewed before May 2023. There were 2 interview rounds.

Round 1 - Technical 

(1 Question)

  • Q1. Mostly on projects and resume
Round 2 - Technical 

(1 Question)

  • Q1. Discussion with Department head

Interview Preparation Tips

Topics to prepare for Luminous Power Technologies Senior Engineer interview:
  • Power Electronics
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
2-4 weeks
Result
Selected Selected

I was interviewed before May 2023.

Round 1 - Technical 

(1 Question)

  • Q1. Wires nd cable related

I applied via LinkedIn and was interviewed before Sep 2021. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all Resume tips
Round 2 - Technical 

(2 Questions)

  • Q1. TELL ME ABOUT YOURSELF
  • Q2. TELL ME ABOUT YOU ? TECHNICAL

Interview Preparation Tips

Topics to prepare for Genus Power Infrastructures Senior Engineer interview:
  • BASIC ELECTRICAL
  • Metering
  • Energy Audit
  • TYPE TESTING
  • PRODUCT VALIDATION
Interview preparation tips for other job seekers - TELL ME ABOUT YOURSELF , TECHNICAL QUALIFICATIONS,
Interview experience
4
Good
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all Resume tips
Round 2 - Technical 

(1 Question)

  • Q1. Technical related questions
Round 3 - HR 

(1 Question)

  • Q1. Salary discussion

Interview Preparation Tips

Interview preparation tips for other job seekers - Joining details
Contribute & help others!
anonymous
You can choose to be anonymous

Microtek International Interview FAQs

How many rounds are there in Microtek International Design Engineer interview?
Microtek International interview process usually has 1 rounds. The most common rounds in the Microtek International interview process are Technical.
How to prepare for Microtek International Design Engineer interview?
Go through your CV in detail and study all the technologies mentioned in your CV. Prepare at least two technologies or languages in depth if you are appearing for a technical interview at Microtek International. The most common topics and skills that interviewers at Microtek International expect are AutoCAD, Creo, Design Engineering, MCB and Product Testing.
What are the top questions asked in Microtek International Design Engineer interview?

Some of the top questions asked at the Microtek International Design Engineer interview -

  1. Tell the difference between MOSFET and I...read more
  2. Tell the principal of Sine wave inver...read more
  3. How to Design an induc...read more

Recently Viewed

INTERVIEWS

KaaShiv InfoTech Company

10 top interview questions

REVIEWS

KaaShiv InfoTech Company

No Reviews

JOBS

Sun Pharmaceutical Industries

No Jobs

INTERVIEWS

Microtek International

No Interviews

SALARIES

Prama Hikvision India

SALARIES

Prama Hikvision India

INTERVIEWS

Microtek International

20 top interview questions

JOBS

Apotex Research

No Jobs

SALARIES

Prama Hikvision India

SALARIES

Prama Hikvision India

Tell us how to improve this page.

Microtek International Design Engineer Interview Process

based on 1 interview

Interview experience

1
  
Bad
View more

Interview Questions from Similar Companies

Havells Interview Questions
4.0
 • 209 Interviews
Exide Industries Interview Questions
3.5
 • 169 Interviews
TCL Interview Questions
4.1
 • 34 Interviews
Okaya Power Interview Questions
3.7
 • 30 Interviews
View all
Microtek International Design Engineer Salary
based on 6 salaries
₹2.8 L/yr - ₹4 L/yr
35% less than the average Design Engineer Salary in India
View more details
Area Sales Manager
129 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Senior Sales Executive
91 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Senior Executive
78 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Assistant Manager
74 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Area Sales Executive
72 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Explore more salaries
Compare Microtek International with

Luminous Power Technologies

4.2
Compare

Su-Kam Power Systems

3.6
Compare

Exide Industries

3.5
Compare

Amaron Batteries

4.6
Compare
Did you find this page helpful?
Yes No
write
Share an Interview