Al Tasnim Enterprises Talent Acquisition Officer Interview Questions and Answers

Q1. Previous experience in detail
Add your answer

Q1. Why are remove the pile head.
Ans. 
Pile heads are removed to allow for further construction or to ensure proper load transfer to the foundation.
• To prepare for further construction on top of the piles

• To ensure proper load transfer to the foundation

• To facilitate the installation of pile caps or beams

• To adjust the pile length if necessary
Answered by AI
Add your answer
Q2. How many deduction of 90 degree angle.
Ans. 
There are four deductions of 90 degree angles.
• A 90 degree angle is formed when two lines intersect at a right angle.

• In a square, all four angles are 90 degrees.

• In a rectangle, opposite angles are 90 degrees.

• In a right triangle, one angle is always 90 degrees.
Answered by AI
Add your answer
Q3. What is static load test and dynamic load test.
Ans. 
Static load test is used to measure the load capacity of a structure under a constant load, while dynamic load test is used to measure the response of a structure to varying loads.
• Static load test involves applying a constant load to a structure and measuring its response over time.

• Dynamic load test involves applying varying loads to a structure to simulate real-life conditions.

• Static load test helps determine the maxi...read more
Answered by AI
Add your answer
Q4. How many tolerance of pile load test.
Ans. 
The number of tolerance of pile load test depends on the specific project requirements and standards.
• The number of tolerance of pile load test can vary based on the project specifications and standards.

• Typically, a tolerance of +/- 5% to +/- 10% is considered acceptable for pile load tests.

• Some projects may have more stringent tolerance requirements depending on the criticality of the structure.

• It is important to refer...read more
Answered by AI
Add your answer
Q5. What is rang Density of bentonite and why is this use.
Ans. 
Bentonite has a range density of 17-22 lb/gal and is used in civil engineering for drilling fluid, grouting, and sealing purposes.
• Range density of bentonite is typically between 17-22 lb/gal.

• Bentonite is used in civil engineering for various purposes such as drilling fluid, grouting, and sealing.

• The range density of bentonite is important for determining its effectiveness in different applications.

• Higher range density ...read more
Answered by AI
Add your answer

Q1. Method of delay analysis
Ans. 
Delay analysis methods are used to determine the causes and impacts of project delays.
• There are various methods of delay analysis such as Critical Path Method (CPM), Time Impact Analysis (TIA), Impacted As-Planned, and As-Built.

• Each method has its own advantages and limitations, and the choice of method depends on the specific circumstances of the project.

• CPM is a commonly used method that analyzes the project schedule...read more
Answered by AI
Add your answer

Demonetization, pros and cons, 5 people in the discussion. HR were friendly and make possible way to comfort the candidates.

Aptitude and technical question-mostly difficult questions.

Q1. Technical interview went with Project Manager and design manager, overall experience good.
Add your answer

Q1. Basic HR questions.
Add your answer

Q1. Related to cad and design
Add your answer

Q1. Stress strain curves
Add your answer
Q2. Asme codes for oil and gas
Ans. 
ASME codes are widely used in the oil and gas industry to ensure safety and quality standards are met.
• ASME B31.3 is the code for process piping in oil and gas facilities

• ASME Section VIII is used for pressure vessels in oil and gas industry

• ASME B31.4 is for liquid pipelines in oil and gas industry
Answered by AI
Add your answer

Q1. On core subject, logical questions
Add your answer

Q1. About Bio, As per resume
Add your answer

Q1. How did you hear about company
Ans. 
Through a job posting on LinkedIn
• Found job posting on LinkedIn

• Researched company after seeing job posting

• Connected with current employees on LinkedIn

• Received referral from a friend or colleague
Answered by AI
Add your answer
Q2. How many experience in high rise with contractor company
Ans. 
I have 8 years of experience working on high rise projects with contractor companies.
• I have worked on multiple high rise projects ranging from 20 to 50 stories.

• Managed structural design and construction of high rise buildings.

• Collaborated with architects, contractors, and clients to ensure project success.
Answered by AI
Add your answer

Asking about Experience like structure, finishing.
What is testing of Steel IS CODE
BILLING OF IS CODE
BBS IS CODE.
CMD IS CODE.

SAFETY HAZARD ANALYSIS.
CONSTRUCTION METHOD STATEMENT.

TYPES OF PLASTER
OUTER PLASTER THICKNESS.
INNER PLASTER THICKNESS.