Filter interviews by
I applied via Naukri.com and was interviewed in Jan 2020. There were 3 interview rounds.
The density of cement is typically around 1440 kg/m³.
The density of cement is a measure of its mass per unit volume.
It is commonly expressed in kilograms per cubic meter (kg/m³).
The density of cement can vary slightly depending on factors such as the type of cement and its composition.
For example, ordinary Portland cement typically has a density of around 1440 kg/m³.
Other types of cement, such as lightweight cement, ma...
The density of bricks varies depending on the type of brick used.
The density of clay bricks ranges from 1,800 to 2,200 kg/m³.
The density of concrete bricks ranges from 1,800 to 2,500 kg/m³.
The density of fly ash bricks ranges from 1,800 to 2,200 kg/m³.
The density of sand-lime bricks ranges from 1,800 to 2,200 kg/m³.
The density of fire bricks ranges from 2,000 to 2,500 kg/m³.
Approximately 278 tiles will be required for the 10x10 feet room.
Convert the room dimensions to the same unit as the tile size.
Calculate the area of the room.
Divide the room area by the tile area to get the number of tiles required.
Round up the result to the nearest whole number.
The density of steel is approximately 7.85 grams per cubic centimeter.
The density of steel is commonly measured in grams per cubic centimeter (g/cm³).
The density of steel can vary depending on the specific type and composition of the steel.
For example, the density of carbon steel is typically around 7.85 g/cm³.
Stainless steel, on the other hand, has a slightly lower density of around 7.75 g/cm³.
The density of steel is ...
Initial setting time of concrete refers to the time taken for the concrete to change from a liquid state to a solid state.
Initial setting time is influenced by factors such as temperature, cement type, water-cement ratio, and admixtures.
The initial setting time is typically measured using the Vicat apparatus, where a needle is used to penetrate the concrete.
The initial setting time is important for construction activit...
The number of bricks used in 1m3 varies depending on the size of the bricks.
The size of the bricks affects the number of bricks used in 1m3.
Different brick sizes have different volumes.
To determine the number of bricks, divide the volume of 1m3 by the volume of a single brick.
Concrete density refers to the mass per unit volume of concrete.
Concrete density is typically measured in kilograms per cubic meter (kg/m³).
It is an important property of concrete as it affects its strength, durability, and other mechanical properties.
The density of concrete can vary depending on the mix design, aggregates used, and the amount of air entrainment.
Normal weight concrete has a density ranging from 2200 to...
Development length is the minimum length of reinforcement required to transfer the stress between the concrete and the reinforcement.
Development length is determined by factors such as the type of reinforcement, concrete strength, and bond strength.
It is necessary to ensure that the reinforcement bars are adequately embedded in the concrete to prevent slippage or failure.
The development length is typically specified in...
Top trending discussions
Mivan slab cycle is a construction technique using aluminum formwork for casting slabs in a repetitive cycle.
Mivan slab cycle involves setting up aluminum formwork panels for casting slabs.
The cycle includes fixing reinforcement, pouring concrete, curing, and then dismantling the formwork for reuse.
This method is efficient, cost-effective, and results in high-quality finishes.
Mivan slab cycle reduces construction time ...
Before concreting, ensure proper formwork, reinforcement placement, concrete mix design, and weather conditions.
Check formwork for proper alignment and stability
Ensure reinforcement bars are correctly placed as per design
Verify concrete mix design meets project specifications
Monitor weather conditions to prevent issues like rain or extreme temperatures affecting the concrete
My expected salary is based on my qualifications, experience, and the industry standards.
I am looking for a competitive salary that reflects my skills and experience in the civil engineering field.
I have researched the average salary range for Civil Site Engineers in this region and industry.
I am open to negotiation based on the overall compensation package offered by the company.
I am looking for a salary that aligns w...
I was interviewed in Jul 2024.
I applied via campus placement at Shri Vidyanikethan Engineering College, Tirupati and was interviewed in Dec 2023. There was 1 interview round.
Grades of concrete refer to the strength of the concrete mix design.
Grades of concrete are denoted by M10, M15, M20, etc. where M stands for mix and the number represents the compressive strength in N/mm^2.
Higher grade concrete has higher compressive strength and is used for structural purposes.
Common grades include M25, M30, M35, and M40 for heavy-duty structures like bridges and high-rise buildings.
Slump in concrete refers to the measure of consistency of freshly mixed concrete.
Slump is determined by the amount of water in the concrete mix.
It is measured by filling a cone-shaped mold with concrete, then lifting the mold to see how much the concrete slumps.
Different types of slumps (true slump, shear slump, collapse slump) indicate different levels of workability and strength of the concrete mix.
Slump test is comm...
Water cement ratio is the ratio of the weight of water to the weight of cement used in a concrete mix.
Water cement ratio is a crucial factor in determining the strength and durability of concrete.
A lower water cement ratio results in stronger and more durable concrete.
The ideal water cement ratio varies depending on the type of concrete mix and its intended use.
For example, a water cement ratio of 0.5 is commonly used ...
M20 grade concrete is a mix of 1 part cement, 1.5 parts sand, and 3 parts aggregate, with a compressive strength of 20 MPa.
M20 grade concrete is commonly used in residential construction.
It is a mix of 1 part cement, 1.5 parts sand, and 3 parts aggregate.
The compressive strength of M20 grade concrete is 20 MPa.
It is suitable for foundations, beams, columns, and slabs.
I applied via Referral and was interviewed in Oct 2023. There was 1 interview round.
Project planning management estimate and costing
posted on 30 Dec 2022
I was interviewed in Nov 2022.
I applied via campus placement at Galgotias College of Engineering and Technology, Greater Noida and was interviewed before Jan 2022. There were 2 interview rounds.
I applied via Walk-in and was interviewed before Apr 2022. There were 2 interview rounds.
based on 9 reviews
Rating in categories
Civil Site Engineer
41
salaries
| ₹1.5 L/yr - ₹4.6 L/yr |
Site Engineer
25
salaries
| ₹2.2 L/yr - ₹4.8 L/yr |
Civil Engineer
9
salaries
| ₹1.8 L/yr - ₹5.5 L/yr |
Senior Surveyor
6
salaries
| ₹3.5 L/yr - ₹4 L/yr |
Junior Engineer Civil
6
salaries
| ₹1.2 L/yr - ₹2.5 L/yr |
Larsen & Toubro Limited
Tata Projects
GMR Group
Hindustan Construction Company