Add office photos
Filter interviews by
Swati Manthol & Allied Chemical Interview Questions and Answers
Be the first one to contribute and help others!
Interview questions from similar companies
Graduate Engineer Trainee (Get) Interview Questions & Answers
Worley
VIPEEN NISWADE
posted on 5 Dec 2024
I applied via campus placement at BRACT's Vishwakarma Institute of Information Technology, Pune and was interviewed in Nov 2024. There were 3 interview rounds.
Basic Aptitude Questions Reasoning & Verbal Ability
How is culture at IT Industries
(12 Questions)
- Q1. What are the tensile forces acts on material
- Ans.
Tensile forces are forces that stretch or pull materials apart.
Tensile forces act in the opposite direction of compressive forces
Examples of tensile forces include stretching a rubber band or pulling on a rope
Tensile strength is a measure of a material's ability to withstand tensile forces
- Q2. Write all formulas you know of Fluid Mechanics
- Ans.
Formulas in Fluid Mechanics
Bernoulli's equation: P + 0.5ρv^2 + ρgh = constant
Continuity equation: A1v1 = A2v2
Navier-Stokes equation: ρ(∂v/∂t + v∇v) = -∇P + μ∇^2v + ρg
Ideal gas law: PV = nRT
Poiseuille's Law: Q = πr^4(ΔP)/(8ηL)
- Q3. Laws of thermodynamics
- Ans.
The fundamental laws of thermodynamics govern the behavior of energy in systems.
First Law of Thermodynamics: Energy cannot be created or destroyed, only transferred or converted.
Second Law of Thermodynamics: The entropy of an isolated system will always increase over time.
Third Law of Thermodynamics: As temperature approaches absolute zero, the entropy of a system approaches a minimum value.
Examples: A car engine conve...
- Q4. What is Fouriers Law write its equation
- Ans.
Fourier's Law describes the flow of heat through a material.
Fourier's Law states that the rate of heat transfer through a material is directly proportional to the negative gradient of temperature and the area perpendicular to the direction of heat flow.
The equation for Fourier's Law is q = -k * A * (dT/dx), where q is the heat transfer rate, k is the thermal conductivity of the material, A is the cross-sectional area, ...
- Q5. Explain Iron Carbon phase diagram
- Ans.
The Iron-Carbon phase diagram illustrates the phases and microstructures of iron-carbon alloys as a function of temperature and composition.
Shows the phases of iron and carbon at different temperatures and compositions
Includes regions for austenite, ferrite, cementite, and pearlite
Critical points such as eutectic point and eutectoid point are marked
Used to predict the microstructure of steel based on composition and he
- Q6. Stress Strain Curve Explain
- Ans.
The stress-strain curve shows the relationship between stress (force applied) and strain (resulting deformation) in a material.
The curve typically consists of three main regions: elastic deformation, plastic deformation, and fracture.
In the elastic region, the material deforms elastically and returns to its original shape when the stress is removed.
The plastic region is where permanent deformation occurs, but the mater...
- Q7. Calculate SFD & BMD
- Ans.
SFD and BMD are calculated using equations of equilibrium and relationships between load, shear force, and bending moment.
Calculate reactions at supports using equations of equilibrium
Determine the shear force at different points along the beam by considering the applied loads and reactions
Calculate the bending moment at different points by integrating the shear force diagram
Plot the SFD and BMD based on the calculated...
- Q8. How to Calculate velocity of fluid flowing through pipe
- Ans.
Velocity of fluid flowing through a pipe can be calculated using the formula Q = A * V, where Q is the flow rate, A is the cross-sectional area of the pipe, and V is the velocity of the fluid.
Calculate the cross-sectional area of the pipe using the formula A = π * r^2, where r is the radius of the pipe.
Determine the flow rate (Q) of the fluid, which is typically measured in cubic meters per second (m^3/s) or liters per...
- Q9. What is Difference between entropy and enthalpy
- Ans.
Entropy is a measure of disorder or randomness in a system, while enthalpy is a measure of the heat energy in a system.
Entropy is a thermodynamic property that measures the amount of energy in a system that is not available to do work.
Enthalpy is a thermodynamic property that measures the total heat content of a system.
Entropy increases in irreversible processes, while enthalpy remains constant.
Entropy is denoted by S,...
- Q10. Draw Refrigeration Cycle Graph
- Ans.
The Refrigeration Cycle graph shows the process of cooling a space by transferring heat from inside to outside.
The cycle starts with the refrigerant entering the compressor as a low-pressure gas.
The refrigerant is compressed, raising its temperature and pressure, before entering the condenser where it releases heat to the surroundings.
After losing heat, the refrigerant becomes a high-pressure liquid and flows into the ...
- Q11. Draw vapour absorption cycle graph
- Ans.
The vapor absorption cycle graph shows the relationship between pressure, temperature, and enthalpy during the process.
The graph typically shows pressure on the y-axis and temperature on the x-axis.
It includes lines representing the various stages of the cycle such as evaporation, absorption, and desorption.
The enthalpy values at different points in the cycle can also be plotted on the graph.
Example: The graph will sho...
- Q12. Draw Rankine otto & diesel cycle graph
- Ans.
The Rankine, Otto, and Diesel cycle graphs are commonly used in thermodynamics to analyze different types of heat engines.
The Rankine cycle is used in steam power plants and consists of four processes: heat addition, isentropic expansion, heat rejection, and isentropic compression.
The Otto cycle is used in spark-ignition engines and consists of four processes: isentropic compression, constant volume heat addition, isen...
Interview Preparation Tips
- Strength of materials
- Thermodynamics
- Heat Transfer
- Fluid Mechanics
Trainee Electrical Engineer Interview Questions & Answers
Coromandel International
Anonymous
posted on 4 Jan 2025
Selected
I applied via Approached by Company and was interviewed in Dec 2024. There were 2 interview rounds.
(3 Questions)
- Q1. What is the purpose of substances?
- Q2. What is the working mechanism of electric motors and what are their applications in various industries?
- Q3. Which safety are used for electrical works
(3 Questions)
- Q1. What are the different types of loads used in electrical systems?
- Q2. What are the various equipment found in a substation, and what are their uses and working principles?
- Q3. What is 5s and uses
Interview Preparation Tips
Airless paint machine service and sell paint demo Interview Questions & Answers
Asian Paints
Anonymous
posted on 31 Dec 2024
(4 Questions)
- Q1. What will my responsibilities be in this role?
- Ans.
Your responsibilities will include servicing airless paint machines, selling paint, and conducting paint demos.
Servicing airless paint machines to ensure they are in proper working condition
Selling paint products to customers based on their needs and preferences
Conducting paint demos to showcase the features and benefits of different paint products
Providing excellent customer service and addressing any concerns or ques
- Q2. What will my responsibilities be in this role?
- Ans.
Your responsibilities will include servicing airless paint machines, selling paint, and conducting paint demos.
Servicing airless paint machines to ensure they are in proper working condition
Selling paint products to customers based on their needs and preferences
Conducting paint demos to showcase the features and benefits of different paint products
Providing excellent customer service and addressing any concerns or ques
- Q3. What will be my salary in my month?
- Q4. How long will the working hours be
Team Lead Operations Interview Questions & Answers
Grasim Industries
Anonymous
posted on 23 Dec 2024
I applied via Campus Placement and was interviewed in Nov 2024. There was 1 interview round.
(5 Questions)
- Q1. What is value of water pH?
- Ans.
The value of water pH indicates its acidity or alkalinity.
Water pH is a measure of how acidic or alkaline the water is.
The pH scale ranges from 0 to 14, with 7 being neutral.
A pH below 7 indicates acidity, while a pH above 7 indicates alkalinity.
Pure water has a pH of 7.
Different substances can affect the pH of water, such as pollutants or minerals.
- Q2. 40% of 800 how much?
- Ans.
40% of 800 is 320.
Calculate 40% of 800 by multiplying 800 by 0.4.
40% of 800 = 800 * 0.4 = 320.
- Q3. How many tons for 1 kilogram?
- Ans.
1 kilogram is equal to 0.001 metric tons.
1 kilogram = 0.001 metric tons
To convert kilograms to metric tons, divide by 1000
Example: 5 kilograms = 5 * 0.001 = 0.005 metric tons
- Q4. Tell about pH scale
- Ans.
pH scale is a measure of acidity or alkalinity of a solution on a scale of 0 to 14.
pH below 7 indicates acidity, with 0 being the most acidic
pH above 7 indicates alkalinity, with 14 being the most alkaline
Pure water has a pH of 7, considered neutral
- Q5. Tell about water properties
- Ans.
Water properties include cohesion, adhesion, high specific heat, universal solvent, and density anomaly.
Cohesion: Water molecules stick to each other due to hydrogen bonding.
Adhesion: Water molecules stick to other substances due to polarity.
High specific heat: Water can absorb a lot of heat before temperature changes.
Universal solvent: Water can dissolve many substances due to its polarity.
Density anomaly: Water is mo
Isha
I applied via Campus Placement and was interviewed in Nov 2024. There were 4 interview rounds.
Aptitude and coding test happened and after that a gd where 4 students fom each group were seleced out of 10 then interviews f2f in college
Keep giving valid points and make sure youre being heard and it doesnt matter if you speak in favor or against
(1 Question)
- Q1. Everything in your resume was asked and basic electronic components Computer networks
(1 Question)
- Q1. BASIC QUESTIONS about family and interest
afnan af
Selected
I applied via Naukri.com and was interviewed in Nov 2024. There were 3 interview rounds.
(1 Question)
- Q1. Could you provide more details about your previous experience?
- Ans.
I have over 5 years of experience in sales, including managing key accounts and exceeding sales targets.
Managed key accounts to ensure customer satisfaction and retention
Consistently exceeded sales targets by implementing effective sales strategies
Developed and maintained strong relationships with clients to drive business growth
(1 Question)
- Q1. Could you describe your academic background and its relevance to the role?
- Ans.
I have a Bachelor's degree in Business Administration with a focus on sales and marketing, which has provided me with a strong foundation for this role.
Bachelor's degree in Business Administration with a focus on sales and marketing
Courses in sales strategies, consumer behavior, and market analysis
Internship experience in a sales role at XYZ Company
Capstone project on developing a sales plan for a new product
(1 Question)
- Q1. How many years do you anticipate staying with the company if selected?
- Ans.
I anticipate staying with the company long-term, as I am looking for stability and growth opportunities.
I am committed to contributing to the company's success and advancing my career within the organization.
I value stability and long-term relationships with employers.
I am excited about the potential growth opportunities within the company and see myself growing along with it.
I applied via Campus Placement and was interviewed in Dec 2024. There were 2 interview rounds.
Generic GD topic. My topic was 'Is social media good or bad?'
(2 Questions)
- Q1. Tell me about yourself.
- Ans.
Experienced professional with a background in retail management and a proven track record of driving sales and improving team performance.
Over 5 years of experience in retail management
Strong leadership skills demonstrated through successful team management
Proven ability to increase sales and meet targets
Excellent communication and interpersonal skills
Passionate about delivering exceptional customer service
- Q2. Are you open to travel to rural areas for sales?
- Ans.
Yes, I am open to travel to rural areas for sales as it allows me to reach a wider customer base and understand diverse market needs.
I have previous experience traveling to rural areas for sales in my current role.
I believe that reaching out to customers in rural areas is essential for expanding the business.
I am willing to travel to rural areas to meet sales targets and build strong customer relationships.
Ramesh Kumar.m
Selected
I applied via Company Website
(2 Questions)
- Q1. Market related questions
- Ans.
Competed company knowledge very important that's business development idea's
- Q2. Additional business development
- Ans.
Additional business development for new customers enrollment Customer cavarege
(2 Questions)
- Q1. New products launching
- Ans.
New products penifeds and additional business development and additional income
- Q2. Product important knowledge
Team handling very important for a job
(2 Questions)
- Q1. New products launching
- Q2. Product important knowledge
Team handling very important for a job
Interview Preparation Tips
Selected
I applied via Referral and was interviewed in Oct 2024. There was 1 interview round.
(5 Questions)
- Q1. What is QAP &ITP
- Ans.
QAP stands for Quality Assurance Plan and ITP stands for Inspection and Test Plan.
QAP outlines the quality control procedures and processes to be followed during a project.
ITP details the specific inspections and tests that will be conducted to ensure quality standards are met.
Both documents are essential for ensuring quality and compliance in projects.
- Q2. How total station work
- Ans.
Total stations are electronic/optical instruments used in surveying and construction to measure angles and distances.
Total stations combine a theodolite for measuring angles with a distance meter to calculate distances.
They use a laser beam to measure distances to objects.
Total stations are commonly used in construction, civil engineering, and land surveying.
They provide accurate measurements for mapping, setting out b...
- Q3. Why soil compactionis done
- Ans.
Soil compaction is done to increase soil density, improve load-bearing capacity, reduce water infiltration, and enhance root growth.
Increase soil density to improve stability and reduce settling
Improve load-bearing capacity for construction projects
Reduce water infiltration to prevent erosion and improve drainage
Enhance root growth by providing a stable environment for plants
Common methods include using heavy machinery
- Q4. Why HDPE liner used
- Ans.
HDPE liner is used for its durability, chemical resistance, and flexibility in various applications.
HDPE liner is chosen for its high durability, able to withstand harsh environmental conditions.
It is chemically resistant, making it ideal for use in containment systems for hazardous materials.
HDPE liner is flexible, allowing it to conform to the shape of the surface it is being applied to.
Common applications include la...
- Q5. How FDD test carried out
- Ans.
FDD tests are carried out by following a structured approach to identify defects in software development.
FDD tests involve creating test cases based on functional requirements
Tests are executed to verify if the software functions as expected
Defects found during testing are logged and prioritized for resolution
Regression testing is performed to ensure that fixes do not introduce new issues
Selected
I applied via Naukri.com and was interviewed in Aug 2024. There were 2 interview rounds.
(3 Questions)
- Q1. Abovt for transmission line
- Q2. Ac and Dc supply diffrent
- Q3. Power supply is switchyard Properly
(2 Questions)
- Q1. Sefty equipment per site responsible
- Ans.
The safety equipment per site is the responsibility of the site engineer.
Ensuring all safety equipment is available and in working condition on site
Regularly inspecting safety equipment to ensure compliance with regulations
Training site personnel on proper use of safety equipment
Maintaining records of safety equipment inspections and maintenance
Coordinating with safety officers to address any safety equipment concerns
- Q2. Emergency Fault found for duties
- Ans.
Emergency fault found for duties requires immediate action to resolve the issue and prevent any further damage or safety hazards.
Identify the nature and location of the fault
Assess the severity of the fault and potential impact on operations
Implement immediate corrective actions to address the fault
Communicate with relevant stakeholders to coordinate response and mitigation efforts
Document the fault, actions taken, and
Interview Preparation Tips
Tell us how to improve this page.
Interview Questions for Popular Designations
Interview Questions from Similar Companies
Swati Manthol & Allied Chemical Reviews and Ratings
based on 2 reviews
Rating in categories
Asian Paints
Berger Paints
Aarti Industries
Grasim Industries
Calculate your in-hand salary
- Home >
- Interviews >
- Swati Manthol & Allied Chemical Interview Questions
