Upload Button Icon Add office photos

Worley

Compare button icon Compare button icon Compare

Filter interviews by

Worley Interview Questions, Process, and Tips

Updated 13 Feb 2025

Top Worley Interview Questions and Answers

View all 80 questions

Worley Interview Experiences

Popular Designations

109 interviews found

Interview experience
5
Excellent
Difficulty level
Hard
Process Duration
Less than 2 weeks
Result
Not Selected

I applied via campus placement at BRACT's Vishwakarma Institute of Information Technology, Pune and was interviewed in Nov 2024. There were 3 interview rounds.

Round 1 - Aptitude Test 

Basic Aptitude Questions Reasoning & Verbal Ability

Round 2 - Group Discussion 

How is culture at IT Industries

Round 3 - Technical 

(12 Questions)

  • Q1. What are the tensile forces acts on material
  • Ans. 

    Tensile forces are forces that stretch or pull materials apart.

    • Tensile forces act in the opposite direction of compressive forces

    • Examples of tensile forces include stretching a rubber band or pulling on a rope

    • Tensile strength is a measure of a material's ability to withstand tensile forces

  • Answered by AI
  • Q2. Write all formulas you know of Fluid Mechanics
  • Ans. 

    Formulas in Fluid Mechanics

    • Bernoulli's equation: P + 0.5ρv^2 + ρgh = constant

    • Continuity equation: A1v1 = A2v2

    • Navier-Stokes equation: ρ(∂v/∂t + v∇v) = -∇P + μ∇^2v + ρg

    • Ideal gas law: PV = nRT

    • Poiseuille's Law: Q = πr^4(ΔP)/(8ηL)

  • Answered by AI
  • Q3. Laws of thermodynamics
  • Ans. 

    The fundamental laws of thermodynamics govern the behavior of energy in systems.

    • First Law of Thermodynamics: Energy cannot be created or destroyed, only transferred or converted.

    • Second Law of Thermodynamics: The entropy of an isolated system will always increase over time.

    • Third Law of Thermodynamics: As temperature approaches absolute zero, the entropy of a system approaches a minimum value.

    • Examples: A car engine conve...

  • Answered by AI
  • Q4. What is Fouriers Law write its equation
  • Ans. 

    Fourier's Law describes the flow of heat through a material.

    • Fourier's Law states that the rate of heat transfer through a material is directly proportional to the negative gradient of temperature and the area perpendicular to the direction of heat flow.

    • The equation for Fourier's Law is q = -k * A * (dT/dx), where q is the heat transfer rate, k is the thermal conductivity of the material, A is the cross-sectional area, ...

  • Answered by AI
  • Q5. Explain Iron Carbon phase diagram
  • Ans. 

    The Iron-Carbon phase diagram illustrates the phases and microstructures of iron-carbon alloys as a function of temperature and composition.

    • Shows the phases of iron and carbon at different temperatures and compositions

    • Includes regions for austenite, ferrite, cementite, and pearlite

    • Critical points such as eutectic point and eutectoid point are marked

    • Used to predict the microstructure of steel based on composition and he

  • Answered by AI
  • Q6. Stress Strain Curve Explain
  • Ans. 

    The stress-strain curve shows the relationship between stress (force applied) and strain (resulting deformation) in a material.

    • The curve typically consists of three main regions: elastic deformation, plastic deformation, and fracture.

    • In the elastic region, the material deforms elastically and returns to its original shape when the stress is removed.

    • The plastic region is where permanent deformation occurs, but the mater...

  • Answered by AI
  • Q7. Calculate SFD & BMD
  • Ans. 

    SFD and BMD are calculated using equations of equilibrium and relationships between load, shear force, and bending moment.

    • Calculate reactions at supports using equations of equilibrium

    • Determine the shear force at different points along the beam by considering the applied loads and reactions

    • Calculate the bending moment at different points by integrating the shear force diagram

    • Plot the SFD and BMD based on the calculated...

  • Answered by AI
  • Q8. How to Calculate velocity of fluid flowing through pipe
  • Ans. 

    Velocity of fluid flowing through a pipe can be calculated using the formula Q = A * V, where Q is the flow rate, A is the cross-sectional area of the pipe, and V is the velocity of the fluid.

    • Calculate the cross-sectional area of the pipe using the formula A = π * r^2, where r is the radius of the pipe.

    • Determine the flow rate (Q) of the fluid, which is typically measured in cubic meters per second (m^3/s) or liters per...

  • Answered by AI
  • Q9. What is Difference between entropy and enthalpy
  • Ans. 

    Entropy is a measure of disorder or randomness in a system, while enthalpy is a measure of the heat energy in a system.

    • Entropy is a thermodynamic property that measures the amount of energy in a system that is not available to do work.

    • Enthalpy is a thermodynamic property that measures the total heat content of a system.

    • Entropy increases in irreversible processes, while enthalpy remains constant.

    • Entropy is denoted by S,...

  • Answered by AI
  • Q10. Draw Refrigeration Cycle Graph
  • Ans. 

    The Refrigeration Cycle graph shows the process of cooling a space by transferring heat from inside to outside.

    • The cycle starts with the refrigerant entering the compressor as a low-pressure gas.

    • The refrigerant is compressed, raising its temperature and pressure, before entering the condenser where it releases heat to the surroundings.

    • After losing heat, the refrigerant becomes a high-pressure liquid and flows into the ...

  • Answered by AI
  • Q11. Draw vapour absorption cycle graph
  • Ans. 

    The vapor absorption cycle graph shows the relationship between pressure, temperature, and enthalpy during the process.

    • The graph typically shows pressure on the y-axis and temperature on the x-axis.

    • It includes lines representing the various stages of the cycle such as evaporation, absorption, and desorption.

    • The enthalpy values at different points in the cycle can also be plotted on the graph.

    • Example: The graph will sho...

  • Answered by AI
  • Q12. Draw Rankine otto & diesel cycle graph
  • Ans. 

    The Rankine, Otto, and Diesel cycle graphs are commonly used in thermodynamics to analyze different types of heat engines.

    • The Rankine cycle is used in steam power plants and consists of four processes: heat addition, isentropic expansion, heat rejection, and isentropic compression.

    • The Otto cycle is used in spark-ignition engines and consists of four processes: isentropic compression, constant volume heat addition, isen...

  • Answered by AI

Interview Preparation Tips

Topics to prepare for Worley Graduate Engineer Trainee (Get) interview:
  • Strength of materials
  • Thermodynamics
  • Heat Transfer
  • Fluid Mechanics
Interview preparation tips for other job seekers - Go by preparing each and every subject of Mechanical Engineering they ask very deep technical questions prepare all types of graphs especially

Top Worley Graduate Engineer Trainee (Get) Interview Questions and Answers

Q1. Draw Stress vs strain curves, what are over reinforced section and under reinforced section
View answer (1)

Graduate Engineer Trainee (Get) Interview Questions asked at other Companies

Q1. Q: 1 What is IC engine? What is the types of IC engine? Q:2 Difference between Otto cycle and Diesel cycle? What is the process of both cycle and what is the effeciency of both cycle ? Which one is good in effeciency? Q:3 Difference between... read more
View answer (2)

Rate your
company

🤫 100% anonymous

How was your last interview experience?

Share interview
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Not Selected

I applied via campus placement at Jawaharlal Nehru Technological University (JNTU) and was interviewed in Dec 2024. There was 1 interview round.

Round 1 - Group Discussion 

GD topic was "pros and cons of strat ups"
Everty member who gave GD was eligible for interview
They gave marks for every candidate

Interview Preparation Tips

Interview preparation tips for other job seekers - There we 32 chemical engineering students to be interviewed.
It was pool campus interview in hyderabad at jntuh College.
GD was done in 10 members group
The topic was "pros and cons of start ups"
Then interview....
For first 6 members they asked questions on FM (even if we said our favorite subjects which didn't include FM,they asked questions from it.)
The questions were:
What is npsh
What is cavitation
What happens if vapor pressure decreases in pumps
How much should be the minimum vapor pressure....any formulae
Functions used in FM
Suction head formula and their types
Formulae used in FM
Bernoulli's theory
Questions based on minor and major project(remember the formulae used in projects)
In thermodynamics and HT
Modes of heat transfer
How do you relate enthalpy and entropy and efficiency of pump( questions on minor project)

For last 4 members they asked most questions from CRE(they got bored from asking same FM questions)

Top Worley Graduate Engineer Trainee (Get) Interview Questions and Answers

Q1. Draw Stress vs strain curves, what are over reinforced section and under reinforced section
View answer (1)

Graduate Engineer Trainee (Get) Interview Questions asked at other Companies

Q1. Q: 1 What is IC engine? What is the types of IC engine? Q:2 Difference between Otto cycle and Diesel cycle? What is the process of both cycle and what is the effeciency of both cycle ? Which one is good in effeciency? Q:3 Difference between... read more
View answer (2)
Worley Interview Questions and Answers for Freshers
illustration image
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Campus Placement and was interviewed in Dec 2024. There were 4 interview rounds.

Round 1 - Aptitude Test 

Electrical based and aptitude

Round 2 - Group Discussion 

About renewable and all were interactive

Round 3 - Technical 

(1 Question)

  • Q1. About our technical knowledge
Round 4 - HR 

(1 Question)

  • Q1. About us intro strength weakness projects intern

Graduate Engineer Interview Questions asked at other Companies

Q1. What is Finite Element Analysis? Explain using examples.
View answer (1)
Interview experience
3
Average
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Not Selected

I applied via Campus Placement and was interviewed in Oct 2024. There were 3 interview rounds.

Round 1 - Aptitude Test 

It was a one hour test including aptitute and subject matter questions

Round 2 - Group Discussion 

We were divided in groups of 14 people. GD went for around 15 mins and the topic was Russia ukraine war.

Round 3 - Technical 

(2 Questions)

  • Q1. Draw and explain Rankine cycle
  • Ans. 

    Rankine cycle is a thermodynamic cycle used in steam power plants to generate electricity.

    • Rankine cycle consists of four main components: a pump, a boiler, a turbine, and a condenser.

    • Water is pumped into the boiler where it is heated to create high pressure steam.

    • The high pressure steam is then fed into a turbine where it expands, producing mechanical work.

    • After exiting the turbine, the steam is condensed back into wat...

  • Answered by AI
  • Q2. Internship related technical questions

Top Worley Graduate Engineer Trainee (Get) Interview Questions and Answers

Q1. Draw Stress vs strain curves, what are over reinforced section and under reinforced section
View answer (1)

Graduate Engineer Trainee (Get) Interview Questions asked at other Companies

Q1. Q: 1 What is IC engine? What is the types of IC engine? Q:2 Difference between Otto cycle and Diesel cycle? What is the process of both cycle and what is the effeciency of both cycle ? Which one is good in effeciency? Q:3 Difference between... read more
View answer (2)

Worley interview questions for popular designations

 Process Engineer

 (7)

 Graduate Engineer Trainee (Get)

 (5)

 Piping Engineer

 (5)

 Assistant Manager

 (4)

 Mechanical Engineer

 (4)

 Deputy Manager

 (3)

 Engineer Trainee

 (3)

 Graduate Engineer

 (3)

L2 Engineer Interview Questions & Answers

user image Madras Food

posted on 12 Dec 2024

Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
-
Result
Not Selected

I applied via Company Website and was interviewed in Nov 2024. There was 1 interview round.

Round 1 - Technical 

(1 Question)

  • Q1. Hvac system full details
  • Ans. 

    An HVAC system is a heating, ventilation, and air conditioning system that controls the temperature, humidity, and air quality in a building.

    • Consists of a furnace or boiler for heating

    • Includes a central air conditioner for cooling

    • Utilizes ductwork to distribute air throughout the building

    • May have a thermostat to control temperature settings

    • Can include air filters for improving indoor air quality

  • Answered by AI

L2 Engineer Interview Questions asked at other Companies

Q1. 4. What is difference between radiography testing (RT) and ultrasonic testing (UT)
View answer (1)

Get interview-ready with Top Worley Interview Questions

Interview experience
4
Good
Difficulty level
Moderate
Process Duration
2-4 weeks
Result
Selected Selected

I applied via Approached by Company and was interviewed in Jul 2024. There was 1 interview round.

Round 1 - Technical 

(2 Questions)

  • Q1. Major difference between Hrg and Lrg?
  • Ans. 

    HRG stands for Human Resource Group while LRG stands for Large Retail Group.

    • HRG focuses on managing human resources within an organization

    • LRG focuses on managing a large retail business

    • HRG deals with employee relations, recruitment, training, and development

    • LRG deals with sales, inventory management, customer service, and marketing

  • Answered by AI
  • Q2. How to perform transformer sizing
  • Ans. 

    Transformer sizing involves calculating the appropriate size of a transformer based on load requirements.

    • Determine the total load requirements in kVA

    • Consider the load factor and diversity factor

    • Calculate the transformer size based on the total load requirements

    • Ensure the transformer is rated for the appropriate voltage and frequency

    • Consult with a professional engineer if needed

  • Answered by AI

Assistant Manager Interview Questions asked at other Companies

Q1. You are Handling cash operations then how you manage operations with sales ?
View answer (86)

Jobs at Worley

View all
Interview experience
2
Poor
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Aptitude Test 

Basics of Electrical engineering

Round 2 - Group Discussion 

General Topics Corona

Round 3 - Technical 

(1 Question)

  • Q1. What is transformer

Top Worley Graduate Engineer Trainee (Get) Interview Questions and Answers

Q1. Draw Stress vs strain curves, what are over reinforced section and under reinforced section
View answer (1)

Graduate Engineer Trainee (Get) Interview Questions asked at other Companies

Q1. Q: 1 What is IC engine? What is the types of IC engine? Q:2 Difference between Otto cycle and Diesel cycle? What is the process of both cycle and what is the effeciency of both cycle ? Which one is good in effeciency? Q:3 Difference between... read more
View answer (2)

Lead Engineer Interview Questions & Answers

user image Umesh Gangwar

posted on 14 Aug 2024

Interview experience
5
Excellent
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Technical 

(2 Questions)

  • Q1. Question about role and responsibilities
  • Q2. What structure Fabrication method statement , WPS etc
  • Ans. 

    Fabrication method statement includes details on how a structure will be fabricated, while WPS (Welding Procedure Specification) outlines welding procedures.

    • Fabrication method statement details the step-by-step process of fabricating a structure

    • WPS specifies the welding procedures to be followed during fabrication

    • Both documents are crucial for ensuring quality and safety in the fabrication process

  • Answered by AI

Lead Engineer Interview Questions asked at other Companies

Q1. What is the resistance value of tripping & closing coil of vcb?
View answer (8)
Interview experience
4
Good
Difficulty level
Easy
Process Duration
Less than 2 weeks
Result
Not Selected

I applied via Recruitment Consulltant and was interviewed in Jul 2024. There was 1 interview round.

Round 1 - HR 

(2 Questions)

  • Q1. From project conception to execution, what would you do to ensure successful delivery
  • Ans. 

    To ensure successful delivery from project conception to execution, I would focus on clear communication, detailed planning, proactive problem-solving, and regular monitoring.

    • Establish clear project goals and objectives

    • Create a detailed project plan with timelines and milestones

    • Regularly communicate with stakeholders to ensure alignment and address any issues

    • Proactively identify and address potential risks and challeng...

  • Answered by AI
  • Q2. What technical experience do you have
  • Ans. 

    I have over 5 years of technical experience in project management, construction, and engineering design.

    • Managed multiple construction projects from initiation to completion

    • Proficient in AutoCAD and other design software

    • Experience in creating project schedules and budgets

    • Knowledge of construction materials and methods

    • Collaborated with cross-functional teams to ensure project success

  • Answered by AI

Project Engineer Interview Questions asked at other Companies

Q1. Triangle Star PatternPrint the following pattern for the given N number of rows. Pattern for N = 4 * ** *** **** Note : There are no spaces between the stars (*). Input format : Integer N (Total no. of rows) Output format : Pattern in N l... read more
View answer (7)

Principal (Lead )Electrical design Engineer Interview Questions & Answers

user image Anonymous

posted on 9 Jul 2024

Interview experience
5
Excellent
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Technical 

(2 Questions)

  • Q1. Your technical Skills and your work experience
  • Q2. Technical skill and work experience
Contribute & help others!
anonymous
You can choose to be anonymous

Worley Interview FAQs

How many rounds are there in Worley interview?
Worley interview process usually has 2-3 rounds. The most common rounds in the Worley interview process are Technical, Resume Shortlist and HR.
How to prepare for Worley interview?
Go through your CV in detail and study all the technologies mentioned in your CV. Prepare at least two technologies or languages in depth if you are appearing for a technical interview at Worley. The most common topics and skills that interviewers at Worley expect are Consulting, Recruitment, HP Data Protector, Procurement and Engineering Services.
What are the top questions asked in Worley interview?

Some of the top questions asked at the Worley interview -

  1. Draw Stress vs strain curves, what are over reinforced section and under reinfo...read more
  2. what precaution should be taken before starting any confined space wor...read more
  3. Draw a simple line chart for 10 km action plan with in 10 min ( including all s...read more
How long is the Worley interview process?

The duration of Worley interview process can vary, but typically it takes about less than 2 weeks to complete.

Recently Viewed

INTERVIEWS

Boeing

85 interviews

Tell us how to improve this page.

Worley Interview Process

based on 90 interviews

Interview experience

4.4
  
Good
View more

Saint-Gobain

We thank our employees for rating us 4/5 on AmbitionBox

Interview Questions from Similar Companies

TechnipFMC Interview Questions
4.0
 • 70 Interviews
Bechtel Interview Questions
4.0
 • 69 Interviews
Wood Group Interview Questions
3.7
 • 57 Interviews
Saipem Interview Questions
4.1
 • 45 Interviews
Petrofac Interview Questions
4.3
 • 41 Interviews
Aker Solutions Interview Questions
4.0
 • 34 Interviews
View all

Worley Reviews and Ratings

based on 1k reviews

4.1/5

Rating in categories

3.7

Skill development

4.2

Work-life balance

3.7

Salary

3.9

Job security

4.1

Company culture

3.4

Promotions

3.8

Work satisfaction

Explore 1k Reviews and Ratings
Assurance Advisor

Mumbai

5-10 Yrs

Not Disclosed

EDS Specialist

Mumbai,

Navi Mumbai

8-15 Yrs

Not Disclosed

Explore more jobs
Process Engineer
324 salaries
unlock blur

₹4.5 L/yr - ₹16.5 L/yr

Deputy Manager
204 salaries
unlock blur

₹12 L/yr - ₹33 L/yr

Piping Designer
157 salaries
unlock blur

₹4.4 L/yr - ₹15.2 L/yr

Piping Design Engineer
153 salaries
unlock blur

₹6.3 L/yr - ₹23.4 L/yr

Design Engineer
150 salaries
unlock blur

₹3.8 L/yr - ₹15.8 L/yr

Explore more salaries
Compare Worley with

Jacobs Engineering Group

4.1
Compare

Fluor Corporation

4.3
Compare

Bechtel

4.0
Compare

McDermott International

4.3
Compare
Did you find this page helpful?
Yes No
write
Share an Interview
Rate your experience using AmbitionBox
Terrible
Terrible
Poor
Poor
Average
Average
Good
Good
Excellent
Excellent