Filter interviews by
I applied via Naukri.com and was interviewed in May 2021. There were 3 interview rounds.
The unit weight of steel refers to the weight of a specific volume of steel.
The unit weight of steel is typically measured in pounds per cubic foot or kilograms per cubic meter.
The specific unit weight of steel can vary depending on the type and grade of steel.
For example, the unit weight of mild steel is approximately 490 pounds per cubic foot or 7850 kilograms per cubic meter.
On the other hand, the unit weight of sta...
I applied via Walk-in
The SOP (Standard Operating Procedure) of all works is a set of documented instructions that outline the steps to be followed for completing tasks.
SOPs provide consistency and ensure that tasks are performed correctly and efficiently.
They help in training new employees and serve as a reference guide for existing employees.
SOPs can cover various aspects such as safety procedures, quality control, maintenance, and troubl...
DLR stands for Detailed Project Report and DPR stands for Detailed Design Report. They are both important documents in engineering projects.
DLR is prepared before the start of a project and includes detailed information about the project scope, objectives, feasibility, and cost estimates.
DPR is prepared during the design phase of a project and provides detailed information about the design specifications, calculations,...
The quantity achieved is dependent on the manpower available.
The more manpower available, the higher the quantity that can be achieved.
Efficient utilization of manpower can lead to higher productivity.
Manpower shortage can result in lower quantity achieved.
Automation and technology can help in achieving higher quantity with less manpower.
Proper planning and coordination are essential to optimize manpower and achieve de
I applied via Walk-in and was interviewed before Feb 2022. There were 3 interview rounds.
Shapoorji Pallonji Group interview questions for designations
I applied via Walk-in and was interviewed before Nov 2019. There were 3 interview rounds.
Top trending discussions
I applied via Job Portal and was interviewed in Mar 2024. There was 1 interview round.
Grade of M20 refers to the mix ratio of concrete where M denotes mix and 20 represents the compressive strength in N/mm^2 after 28 days.
M20 concrete mix consists of 1 part cement, 1.5 parts sand, and 3 parts aggregate.
The compressive strength of M20 concrete after 28 days is 20 N/mm^2.
It is commonly used for residential construction like foundations, slabs, and beams.
Grade of M25 refers to the mix design of concrete with a compressive strength of 25 MPa.
M25 grade concrete is a mix design with a compressive strength of 25 MPa after 28 days of curing.
It is commonly used in construction for residential buildings, bridges, and pavements.
The mix proportion for M25 grade concrete is usually 1:1:2 (cement:sand:aggregate).
4.75 to 10 size of sieve refers to the range of particle sizes that can pass through the sieve.
4.75 to 10 size of sieve indicates the range of particle sizes that can pass through the sieve mesh.
Particles smaller than 4.75 will pass through, while particles larger than 10 will be retained on the sieve.
This range is commonly used in particle size analysis in industries like construction and mining.
Sinking fund method is a way for a company to set aside money over time to repay a debt or replace an asset.
Sinking fund method involves regular contributions to a fund specifically designated for repaying debt or replacing assets.
The purpose of the sinking fund is to ensure that enough money is available when the debt matures or the asset needs to be replaced.
By using the sinking fund method, a company can avoid havin...
An annuity is a financial product that provides a series of payments at regular intervals.
Annuities are typically used for retirement income or to provide a steady income stream.
There are different types of annuities such as fixed annuities, variable annuities, and indexed annuities.
Annuities can be purchased with a lump sum payment or through a series of payments over time.
The payments from an annuity can be guarantee...
After the shortlisting of CVs, list was sent for those who were eligible for the OT. The online test included aptitude + technical. There were pretty easy to moderate questions but time was less.
I applied via Approached by Company and was interviewed in Oct 2023. There were 3 interview rounds.
based on 2 interviews
3 Interview rounds
based on 47 reviews
Rating in categories
Deputy Manager
614
salaries
| ₹6 L/yr - ₹16.6 L/yr |
Senior Engineer
428
salaries
| ₹4 L/yr - ₹12 L/yr |
Construction Engineer
301
salaries
| ₹3 L/yr - ₹9 L/yr |
Civil Site Engineer
228
salaries
| ₹1.5 L/yr - ₹9 L/yr |
Civil Supervisor
223
salaries
| ₹1.5 L/yr - ₹5.6 L/yr |
Tata Group
Reliance Industries
Adani Group
Mahindra & Mahindra