Logisch Technologies Interview Questions and Answers

Q1. I am krishna murthy p
Add your answer
Q2. I am Instrested bmm ispat company one of the best company
Add your answer
Q3. One opportunity given sir
Add your answer
Q4. Electrical engineering
Add your answer
Q5. I am name krishna murthy p i am stady diploma electrical engineering I am experience totally 8 years
Add your answer

Q1. Brief about your education, career, previous projects handled, and role & responsibility in past organisations?
Add your answer
Q2. Current roles & responsibilities and value addition done by you and your team?
Add your answer
Q3. Process flow for planning throughout project life-cycle?
Add your answer
Q4. Critical/concerning areas to be monitored?
Add your answer
Q5. Productivity and permissible material wastage, process to prepare material reconciliation?
Add your answer
Q6. Understanding about claim and type of claim raised/supported to raise in past experience?
Add your answer
Q7. Experience of technical aspects and planning assessment required at tendering stage, capabilities to prepare tender submittals and proving insights to management on same?
Add your answer
Q8. Necessity of providing PMO support to management?
Add your answer
Q9. Understanding about role & responsibility of regional planning manager?
Add your answer
Q10. MIS and type of reports prepared in past and their significance for Top managemennt?
Add your answer

Q1. What is your achievement?
Add your answer
Q2. What problem your faced and how you resolved?
Add your answer
Q3. Any rejection by you in previous years and you resolved the rejection issue.
Add your answer
Q4. Tell me about your current job profile.
Add your answer

It was a technicaL + aptitude test with 60 minutes duration.

Q1. Basic questions regarding the projects that i have done.
Add your answer
Q2. They asked me about my favourite subjects and then they asked some basic questions regarding those subjects.
Add your answer

Q1. HR round in TCE is not an interview round rather it is a video assessment wherein we were given with two HR questions and we have to record a video answering the questions. maximum duration of the video sh...read more
Add your answer

Q1. Highway related Questions
Add your answer
Q2. Highway related
Add your answer

Q1. Highway related Questions
Add your answer
Q2. Highway related Questions
Add your answer

Q1. Highway related Questions
Add your answer

Q1. To be described the previous project and experience
Add your answer
Q2. Project requirement and arrengements
Add your answer
Q3. How to deal with the client
Add your answer
Q4. How to deal with the subcontractor
Add your answer

Q1. What are the mechanical thermal cycles involved in gas turbines?
Add your answer
Q2. What is your work experience with Siemens Teamcenter?
Add your answer

Q1. What are your salary expectations?
Add your answer
Q2. Are you open to relocating for this position?
Add your answer

Q1. What is main reason for belt joint failure?
Ans. 
The main reason for belt joint failure is usually due to improper installation or maintenance.
• Improper installation of the belt joint, such as incorrect alignment or tensioning

• Lack of proper maintenance, leading to wear and tear of the joint

• Use of low-quality materials for the joint

• Excessive load or stress on the belt joint

• Environmental factors like temperature or humidity affecting the joint
Answered by AI
Add your answer
Q2. What was the alignment maximum tolerance?
Ans. 
The alignment maximum tolerance refers to the maximum allowable deviation from the specified alignment.
• Alignment maximum tolerance is the maximum allowable deviation from the specified alignment.

• It is typically expressed in terms of a percentage or a specific measurement unit.

• For example, a machine part may have an alignment maximum tolerance of +/- 0.005 inches.

• Exceeding the alignment maximum tolerance can lead to per
Answered by AI
Add your answer
Q3. How to replace the bucket wheel reclaimer luffing cylinder?
Ans. 
To replace the bucket wheel reclaimer luffing cylinder, follow these steps.
• 1. Shut down the machine and ensure all power sources are disconnected.

• 2. Remove any surrounding components that may obstruct access to the luffing cylinder.

• 3. Use appropriate tools to disconnect the hydraulic hoses and fittings from the cylinder.

• 4. Support the weight of the cylinder as it is removed to prevent damage to surrounding components.

• 5...read more
Answered by AI
Add your answer
Q4. What is different between JSA and HIRA?
Ans. 
JSA stands for Job Safety Analysis, focusing on specific job tasks, while HIRA stands for Hazard Identification and Risk Assessment, focusing on overall workplace hazards.
• JSA is task-specific, focusing on individual job tasks and potential hazards

• HIRA is broader, looking at overall workplace hazards and assessing risks

• JSA involves breaking down a job into steps and identifying potential hazards for each step

• HIRA involv...read more
Answered by AI
Add your answer
Q5. How create a PR in SAP?
Ans. 
To create a PR in SAP, you can use transaction code ME51N or ME21N.
• Use transaction code ME51N to create a purchase requisition in SAP.

• Enter the necessary details such as material, quantity, delivery date, etc.

• Save the purchase requisition and it will be created in the system.

• Alternatively, you can also use transaction code ME21N to create a purchase order directly.
Answered by AI
Add your answer
Q6. What is procedure of pulley replacement?
Ans. 
The procedure of pulley replacement involves identifying the faulty pulley, removing the old pulley, installing the new pulley, and testing the system.
• Identify the faulty pulley by checking for any signs of wear or damage.

• Use appropriate tools to remove the old pulley, such as a pulley puller or wrench.

• Install the new pulley by aligning it properly and securing it in place.

• Test the system to ensure the new pulley is fu...read more
Answered by AI
Add your answer
Q7. Explain the procedure of PTW?
Ans. 
PTW stands for Permit to Work, a procedure used to ensure that work is carried out safely in potentially hazardous environments.
• PTW is a formal written system used to control certain types of work that are identified as potentially hazardous.

• Before starting work, a permit must be obtained from a designated authority.

• The permit outlines the work to be done, the hazards involved, and the necessary precautions to be taken...read more
Answered by AI
Add your answer