Upload Button Icon Add office photos

Descon Engineering

Compare button icon Compare button icon Compare

Filter interviews by

Descon Engineering Assistant Engineer Interview Questions, Process, and Tips

Updated 31 May 2022

Descon Engineering Assistant Engineer Interview Experiences

1 interview found

I applied via Recruitment Consulltant and was interviewed before May 2021. There was 1 interview round.

Round 1 - Technical 

(4 Questions)

  • Q1. What is blinding? Different types of blinds used in o&g?
  • Ans. 

    Blinding is the process of isolating a section of a pipeline or equipment to prevent flow or contamination.

    • Temporary or permanent blinds can be used depending on the situation

    • Common types of blinds include spectacle blinds, paddle blinds, and bleed rings

    • Blinding is often used during maintenance or repair work to ensure safety

    • Blinding can also be used to prevent contamination during storage or transportation

    • Blinding can...

  • Answered by AI
  • Q2. Procedures before starting a work in a refinery equipment,
  • Ans. 

    Before starting work in a refinery equipment, certain procedures must be followed.

    • Obtain a work permit

    • Perform a safety check of the equipment

    • Ensure proper personal protective equipment is worn

    • Verify that all valves are in the correct position

    • Confirm that the equipment is properly grounded

    • Check for any leaks or abnormal conditions

    • Communicate with other workers in the area

    • Follow all established procedures and protocols

  • Answered by AI
  • Q3. What will you do if there's an H2S leak and there's no wind movement,
  • Ans. 

    I will follow the emergency response plan and evacuate the area immediately.

    • Activate the alarm system to alert others in the area

    • Put on personal protective equipment (PPE) including a respirator

    • Evacuate the area immediately and move to a safe location

    • Notify emergency services and follow the emergency response plan

    • Monitor the situation and wait for the all-clear signal before returning to the area

  • Answered by AI
  • Q4. From where you'll advice your workers to start unbloting a heat exchanger head?
  • Ans. 

    I would advise my workers to start unbolting the heat exchanger head from the top and work their way down.

    • Start from the top and work your way down

    • Use appropriate tools and safety equipment

    • Follow proper procedures and guidelines

    • Ensure all bolts are properly labeled and accounted for

    • Inspect the gasket and replace if necessary

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Be confident, answer what you know.

Interview questions from similar companies

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. Related to cad and design

Interview Preparation Tips

Interview preparation tips for other job seekers - Need to be flexible in ur approach.
Interview experience
1
Bad
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Walk-in and was interviewed before Feb 2022. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. Steel and shuttering releted questions
Round 3 - HR 

(1 Question)

  • Q1. Expectation releted questions

Interview Preparation Tips

Interview preparation tips for other job seekers - This company is very good but management is very bed management was not know how to deal with client and how to deal out staff
Interview experience
5
Excellent
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Technical 

(2 Questions)

  • Q1. Questions will be asked on previous company roles and responsibilities.
  • Q2. Depends upon previous experience.
Round 2 - Technical 

(2 Questions)

  • Q1. Basics on structure and finishings
  • Q2. Questions on structure and finishings

Interview Preparation Tips

Interview preparation tips for other job seekers - Be prepared for what u wrote in resume.
Interview experience
3
Average
Difficulty level
-
Process Duration
-
Result
No response
Round 1 - Technical 

(5 Questions)

  • Q1. About current projects. And more about seismic/ wind loads
  • Q2. How to perform RSM method ?
  • Ans. 

    Response Surface Methodology (RSM) is a statistical technique used to model and analyze the relationship between a response variable and multiple input variables.

    • Design a set of experiments based on a factorial design

    • Collect data from the experiments

    • Fit a regression model to the data

    • Analyze the model to determine optimal input settings for the response variable

  • Answered by AI
  • Q3. Soil test report
  • Q4. Foundation uplift
  • Q5. Connection design
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(4 Questions)

  • Q1. How to design floating head assembly From pds
  • Ans. 

    Designing a floating head assembly involves considering various factors such as material selection, sealing mechanisms, and thermal expansion.

    • Select appropriate materials for the floating head assembly based on the application requirements.

    • Design effective sealing mechanisms to prevent leakage and ensure proper functioning.

    • Consider thermal expansion and contraction to accommodate temperature variations.

    • Ensure proper al...

  • Answered by AI
  • Q2. H2s service for pressure vessel
  • Ans. 

    H2S service for pressure vessel refers to the use of hydrogen sulfide in a pressure vessel.

    • H2S service involves the handling and containment of hydrogen sulfide gas in a pressure vessel.

    • Pressure vessels used in H2S service must be designed and constructed to withstand the corrosive effects of hydrogen sulfide.

    • Special materials and coatings may be required to prevent hydrogen sulfide from corroding the pressure vessel.

    • R...

  • Answered by AI
  • Q3. Different types of gasket
  • Ans. 

    Gaskets are mechanical seals used to prevent leakage between two surfaces. There are various types of gaskets available.

    • Sheet gaskets

    • Spiral wound gaskets

    • Ring gaskets

    • Metallic gaskets

    • Rubber gaskets

    • Cork gaskets

    • Non-asbestos gaskets

  • Answered by AI
  • Q4. Kamprofile and SpWd as per Asme

Interview Preparation Tips

Interview preparation tips for other job seekers - 4 people taking interview in worley Parsons including Hod and department manager

Skills evaluated in this interview

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. Only design related queries
Round 3 - HR 

(1 Question)

  • Q1. Only salary package discussed

Interview Preparation Tips

Interview preparation tips for other job seekers - Just stick to basic and you can crack the interview
Interview experience
4
Good
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(3 Questions)

  • Q1. Tell me about yourself
  • Q2. What you do daily
  • Q3. What is your package
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
2-4 weeks
Result
Selected Selected

I applied via Approached by Company and was interviewed in Jul 2024. There was 1 interview round.

Round 1 - Technical 

(2 Questions)

  • Q1. Major difference between Hrg and Lrg?
  • Ans. 

    HRG stands for Human Resource Group while LRG stands for Large Retail Group.

    • HRG focuses on managing human resources within an organization

    • LRG focuses on managing a large retail business

    • HRG deals with employee relations, recruitment, training, and development

    • LRG deals with sales, inventory management, customer service, and marketing

  • Answered by AI
  • Q2. How to perform transformer sizing
  • Ans. 

    Transformer sizing involves calculating the appropriate size of a transformer based on load requirements.

    • Determine the total load requirements in kVA

    • Consider the load factor and diversity factor

    • Calculate the transformer size based on the total load requirements

    • Ensure the transformer is rated for the appropriate voltage and frequency

    • Consult with a professional engineer if needed

  • Answered by AI
Interview experience
3
Average
Difficulty level
Moderate
Process Duration
2-4 weeks
Result
No response

I applied via Referral and was interviewed in Dec 2023. There was 1 interview round.

Round 1 - Technical 

(1 Question)

  • Q1. Explain hydration
  • Ans. 

    Hydration is the process of providing adequate fluids to the body to maintain proper function.

    • Hydration is essential for overall health and well-being

    • It helps regulate body temperature, transport nutrients, and remove waste

    • Drinking water, consuming fruits and vegetables, and electrolyte-rich beverages are ways to stay hydrated

  • Answered by AI

Descon Engineering Interview FAQs

How many rounds are there in Descon Engineering Assistant Engineer interview?
Descon Engineering interview process usually has 1 rounds. The most common rounds in the Descon Engineering interview process are Technical.
What are the top questions asked in Descon Engineering Assistant Engineer interview?

Some of the top questions asked at the Descon Engineering Assistant Engineer interview -

  1. What will you do if there's an H2S leak and there's no wind moveme...read more
  2. What is blinding? Different types of blinds used in o...read more
  3. From where you'll advice your workers to start unbloting a heat exchanger he...read more

Tell us how to improve this page.

Descon Engineering Assistant Engineer Reviews and Ratings

based on 3 reviews

3.6/5

Rating in categories

2.9

Skill development

3.6

Work-life balance

3.6

Salary

4.2

Job security

3.3

Company culture

2.9

Promotions

3.6

Work satisfaction

Explore 3 Reviews and Ratings
Safety Officer
37 salaries
unlock blur

₹3 L/yr - ₹9.6 L/yr

Mechanical Supervisor
27 salaries
unlock blur

₹4.5 L/yr - ₹16 L/yr

HSE Supervisor
17 salaries
unlock blur

₹5.6 L/yr - ₹20 L/yr

HSE Officer
16 salaries
unlock blur

₹3 L/yr - ₹12.8 L/yr

Planning Engineer
12 salaries
unlock blur

₹10 L/yr - ₹38.2 L/yr

Explore more salaries
Compare Descon Engineering with

Alstom Transportation

3.7
Compare

Saint-Gobain

4.0
Compare

AECOM

4.2
Compare

AtkinsRealis

3.9
Compare
Did you find this page helpful?
Yes No
write
Share an Interview