i
Vihang Group
Filter interviews by
A project is a temporary endeavor undertaken to create a unique product, service, or result.
Projects have defined objectives, scope, and resources.
They have a specific start and end date.
Projects are typically divided into phases or stages.
Examples: building a bridge, developing a software application, organizing an event.
Finishing work in a building should start after the structural work is completed and includes tasks like painting, tiling, and installing fixtures.
Start finishing work after structural work is completed to avoid damage to finishes during construction.
Coordinate with other trades to ensure finishing work can proceed smoothly.
Tasks involved in finishing work include painting, tiling, installing fixtures, and applying fin...
Concrete grade refers to the strength of the concrete mix in terms of the minimum compressive strength it can withstand after 28 days of curing.
Concrete grade is denoted by the M prefix followed by a number, such as M20, M30, etc.
The number in the concrete grade represents the compressive strength of the concrete in megapascals (MPa).
Higher concrete grades indicate higher strength and are typically used for structural ...
The cycle of slab involves various steps in the construction process.
Prepare the site for construction
Place the formwork for the slab
Pour the concrete mixture into the formwork
Allow the concrete to cure and set
Remove the formwork and finish the slab surface
Internal plaster thickness and ratio are important factors in construction projects.
The standard thickness of internal plaster is usually 12mm for walls and 15mm for ceilings.
The ratio of internal plaster is typically 1:6 (1 part cement to 6 parts sand).
The thickness and ratio may vary depending on the specific requirements of the project and the type of surface being plastered.
Slab checking involves verifying the structural integrity and load-bearing capacity of concrete slabs.
Check for proper reinforcement placement and spacing
Verify concrete mix design and curing process
Inspect for any cracks or defects
Ensure slab thickness meets design specifications
Perform load testing if necessary
External plaster thickness and ratio are determined based on the type of surface and desired finish.
External plaster thickness typically ranges from 12mm to 20mm depending on the surface condition.
The ratio of external plaster mix is usually 1:4 (cement:sand) for rough surfaces and 1:6 for smooth finishes.
For better adhesion, a bonding agent may be added to the plaster mix.
Proper curing is essential to ensure the stren
Section and elevation drawings of a bathroom
Include dimensions for all fixtures and fittings
Show the placement of plumbing lines and electrical outlets
Label materials and finishes for walls, floors, and fixtures
A leading engineering company specializing in innovative solutions for various industries.
Provides cutting-edge engineering solutions
Works with a wide range of industries such as automotive, aerospace, and technology
Focuses on research and development to stay ahead of the competition
Received positive feedback on technical skills and leadership abilities.
Received commendation for successfully leading a team in completing a major project ahead of schedule
Recognized for consistently providing innovative solutions to complex technical challenges
Received high ratings for communication skills and ability to collaborate effectively with cross-functional teams
I applied via Walk-in
I applied via Approached by Company and was interviewed in Aug 2024. There was 1 interview round.
Density of common construction materials varies, with cement around 1440 kg/m3, steel around 7850 kg/m3, fine aggregate around 1600-1750 kg/m3, and coarse aggregate around 1200-1750 kg/m3.
Cement density: 1440 kg/m3
Steel density: 7850 kg/m3
Fine aggregate density: 1600-1750 kg/m3
Coarse aggregate density: 1200-1750 kg/m3
The weight of the cube used to check the strength of concrete is typically 15 cm x 15 cm x 15 cm and weighs around 29 kg.
Standard size of cube for testing concrete strength is 15 cm x 15 cm x 15 cm
Weight of the cube is usually around 29 kg
The cube is made of concrete from the same batch being tested
The ratio of cement mortar for outer and inner wall plastering varies depending on the type of wall and desired finish.
The ratio of cement mortar for outer wall plastering is usually 1:4 (1 part cement to 4 parts sand).
The ratio of cement mortar for inner wall plastering is typically 1:6 (1 part cement to 6 parts sand).
However, the ratio can vary based on factors such as the type of wall surface, desired finish, and lo...
My goal is to become a proficient Site Engineer by gaining experience, knowledge, and skills in the field.
Continuously seek opportunities to learn and improve technical skills
Work on various projects to gain practical experience
Seek mentorship from experienced engineers
Stay updated with industry trends and technologies
Obtain relevant certifications to enhance credibility
Set specific career milestones to track progress
I envision myself as a Senior Site Engineer leading projects and mentoring junior engineers.
Leading and managing multiple projects simultaneously
Mentoring and training junior engineers
Implementing innovative technologies and practices
Collaborating with cross-functional teams for successful project delivery
I applied via Recruitment Consulltant and was interviewed in Dec 2023. There were 2 interview rounds.
Hook's law states that the force needed to extend or compress a spring is directly proportional to the distance it is stretched or compressed.
Hook's law is a principle in physics that describes the behavior of springs and elastic materials.
It states that the force exerted by a spring is directly proportional to the displacement or change in length of the spring.
The law can be mathematically represented as F = kx, where...
Homeslaw is a law that states that the rate of cooling of an object is proportional to the temperature difference between the object and its surroundings.
Homeslaw is also known as Newton's law of cooling.
It is commonly used in thermodynamics and heat transfer.
The law can be expressed mathematically as dQ/dt = -hA(T - Ts), where dQ/dt is the rate of heat transfer, h is the heat transfer coefficient, A is the surface are...
based on 1 interview
Interview experience
Sales Manager
10
salaries
| ₹4.8 L/yr - ₹7.5 L/yr |
Assistant Manager
6
salaries
| ₹7 L/yr - ₹9 L/yr |
Sales Executive
5
salaries
| ₹4 L/yr - ₹7 L/yr |
Senior Executive
5
salaries
| ₹4.9 L/yr - ₹7.1 L/yr |
Closing Manager
4
salaries
| ₹3 L/yr - ₹8.3 L/yr |
Realty Assistant
Kunal Structure
Omkar Realtors and Developers Group
HM Group