Filter interviews by
I applied via Referral and was interviewed in May 2022. There were 2 interview rounds.
The minimum thickness of a slab depends on various factors such as the load it will bear and the type of material used.
The minimum thickness of a slab is typically determined by structural engineers based on the expected load it will bear.
For residential buildings, the minimum slab thickness is usually around 4 inches (10 cm).
For commercial or industrial buildings, the minimum slab thickness can range from 6 to 8 inche...
The minimum angle of a staircase depends on the building codes and regulations of the specific jurisdiction.
The minimum angle of a staircase is typically determined by building codes and regulations.
In general, a minimum angle of 30 degrees is often required for residential staircases.
For commercial or public buildings, the minimum angle may be higher, such as 35 or 40 degrees.
The purpose of specifying a minimum angle ...
The minimum cover in footing refers to the minimum depth of soil or concrete above the reinforcement in a foundation.
The minimum cover is determined based on factors such as the type of soil, load-bearing capacity, and environmental conditions.
It is important to provide sufficient cover to protect the reinforcement from corrosion and ensure the structural integrity of the footing.
The minimum cover requirements may vary...
The height of a crank bar varies depending on its specific application and design.
The height of a crank bar can be determined by referring to the engineering drawings or specifications of the particular project or equipment.
In general, the height of a crank bar is measured from the base to the highest point of the bar.
The height may also depend on the intended use of the crank bar, such as in machinery or construction.
...
The steel density is the measure of how much mass is contained in a given volume of steel.
Steel density is typically measured in kilograms per cubic meter (kg/m^3).
The density of steel can vary depending on the specific type and composition of the steel.
For example, the density of carbon steel is around 7850 kg/m^3.
Stainless steel, on the other hand, has a density of about 8000 kg/m^3.
The density of steel is an importa...
The ratio of M20 concrete is 1:1.5:3.
The ratio of M20 concrete refers to the proportion of cement, sand, and aggregate used in the mix.
For M20 concrete, the ratio is 1 part cement, 1.5 parts sand, and 3 parts aggregate.
This ratio is commonly used for general construction purposes.
The standard height of a ceiling varies depending on the type of building and its purpose.
The standard height for residential ceilings is typically around 8 to 9 feet.
Commercial buildings often have higher ceilings, ranging from 10 to 12 feet or more.
In industrial settings, ceilings can be even higher to accommodate large machinery or equipment.
Certain specialized buildings like theaters or auditoriums may have much hi...
The minimum bar in a square column refers to the minimum amount of reinforcement required for the column.
The minimum bar in a square column is determined by the size and design of the column.
It is typically specified in terms of the diameter and spacing of the reinforcement bars.
The purpose of the minimum bar is to provide adequate strength and stability to the column.
The minimum bar requirements may vary depending on ...
Development length is the minimum length of reinforcement required to transfer the stress between the steel and concrete.
Development length is determined based on the type of reinforcement and the bond strength between steel and concrete.
It is necessary to ensure that the reinforcement bars are properly embedded in the concrete to provide the required strength.
Development length is influenced by factors such as bar dia...
I applied via Walk-in and was interviewed in Apr 2024. There was 1 interview round.
Shuttering in expansion joint columns is done by providing proper gaps to accommodate movement. M30 mix ratio is 1:1:2. How to calculate cutting length with deductions. Concrete strength after 14 days.
Shuttering in expansion joint columns involves providing gaps to allow for movement
M30 design mix ratio is 1:1:2 (1 part cement, 1 part sand, 2 parts aggregate)
To calculate cutting length, deduct the cover, half of the di...
I applied via Naukri.com and was interviewed in Aug 2023. There were 2 interview rounds.
posted on 3 Jul 2022
I applied via Company Website and was interviewed in Jun 2022. There were 4 interview rounds.
I have Good comunication ,all contracts & management team,
I applied via LinkedIn and was interviewed in Mar 2022. There were 2 interview rounds.
Civil engineers play a crucial role in the construction field and management.
Designing and planning construction projects
Ensuring compliance with building codes and regulations
Managing budgets and resources
Overseeing construction progress and quality
Collaborating with architects, contractors, and other professionals
Ensuring safety and environmental standards are met
Providing technical advice and solutions to problems
Ma
The initial process of works execution involves planning, designing, and obtaining necessary permits and approvals.
Conduct site investigation and survey
Develop project plan and design
Obtain necessary permits and approvals
Mobilize resources and equipment
Establish project schedule and budget
The least count of an Auto level is the smallest measurement that can be read. Auto levels are used for leveling and measuring heights.
The least count of an Auto level is usually 0.5 mm
Auto levels are used for leveling and measuring heights of different points on a site
They are used to determine the difference in height between two points
Auto levels are also used to establish a horizontal line of sight
They are commonly
BBS & Abstract measurements sheet can be prepared by following a systematic approach.
Understand the project requirements and specifications
Identify the elements and quantities to be measured
Prepare a detailed drawing or plan of the structure
Calculate the total quantities of materials required
Prepare a Bill of Quantities (BOQ) and Abstract measurements sheet
Ensure accuracy and consistency in measurements
Update the BBS a
Pore cut test is a method to determine the permeability of soil.
It involves cutting a small cylindrical sample of soil and measuring the time it takes for water to flow through it.
The test helps in determining the suitability of soil for construction purposes.
It is commonly used in civil engineering and geotechnical investigations.
The test results can also be used to estimate the rate of settlement of soil.
Pore cut tes...
I applied via Referral and was interviewed in Nov 2020. There were 3 interview rounds.
We implemented Lean Construction methodologies to improve quality and reduce project duration and costs.
Implemented Lean Construction methodologies
Used value engineering to optimize project costs
Implemented quality control measures at every stage of the project
Utilized project management software for efficient scheduling and resource allocation
Implemented continuous improvement processes to identify and address bottlen...
I applied via Naukri.com and was interviewed before Dec 2021. There were 2 interview rounds.
I applied via Recruitment Consultant and was interviewed in Nov 2020. There were 3 interview rounds.
Store Manager
4
salaries
| ₹7.3 L/yr - ₹9.3 L/yr |
Commercial Assistant
4
salaries
| ₹1.4 L/yr - ₹2.2 L/yr |
Shift Production Officer
4
salaries
| ₹3 L/yr - ₹4.3 L/yr |
Assistant Manager
3
salaries
| ₹5.5 L/yr - ₹5.5 L/yr |
Junior Production Officer
3
salaries
| ₹2.7 L/yr - ₹2.7 L/yr |
Asian Paints
Berger Paints
Aarti Industries
Grasim Industries