i
RSPL Group
Proud winner of ABECA 2024 - AmbitionBox Employee Choice Awards
Filter interviews by
Vibration can be checked using vibration sensors and analyzers to measure frequency, amplitude, and intensity.
Use vibration sensors to detect and measure vibrations
Analyze the data collected by the sensors to determine frequency, amplitude, and intensity of the vibrations
Compare the measured values to acceptable limits or standards to assess the severity of the vibration
Take corrective actions if necessary to reduce or...
Questions related to SLD, transformer, DG, interlocking, PM, reports, and SAP knowledge for Electrical Engineer position.
SLD of power flow in current company
Ratings of transformer and DG
Interlocking for a Circuit breaker with SLD
Checklist of DG i.e types of checks used for DG
Preventive maintenance of DG
PM of a motor
Types of reports/logbook made
SAP knowledge
The protection system of a power transformer ensures its safe operation by detecting and mitigating faults.
Protection systems monitor various parameters of the transformer such as temperature, oil level, and winding currents.
Differential protection is commonly used to detect internal faults by comparing the currents entering and leaving the transformer.
Buchholz relay is used to detect and isolate faults in the oil-fill...
Commissioning of HT motor involves testing and verifying its performance before putting it into operation.
Visual inspection of motor and its components
Checking electrical connections and insulation resistance
Testing of motor windings and bearings
Verification of motor performance under load conditions
Adjustment of motor parameters as per requirements
Documentation of commissioning process and results
RSPL Group interview questions for designations
Top trending discussions
I was interviewed in Dec 2024.
I am a dedicated Electrical Engineer with a strong background in designing and implementing electrical systems.
Graduated with a degree in Electrical Engineering from XYZ University
Experienced in designing and testing electrical systems for commercial buildings
Proficient in using CAD software for schematic design
Strong problem-solving skills and attention to detail
Completed internships at ABC Engineering firm
The procedure for checking an induction motor involves visual inspection, insulation resistance testing, and running tests.
Perform a visual inspection to check for any physical damage or loose connections.
Conduct insulation resistance testing to ensure the motor windings are not shorted to ground.
Run no-load and full-load tests to check the motor's performance and efficiency.
Check the motor's temperature during operati...
I am a dedicated Electrical Engineer with a strong background in designing and implementing electrical systems.
Graduated with a degree in Electrical Engineering from XYZ University
Experienced in designing and testing electrical systems for commercial buildings
Proficient in using CAD software for schematic design
Strong problem-solving skills and attention to detail
Completed internships at ABC Company and gained hands-on
Procedure to check industrial earthing involves visual inspection, resistance measurement, and continuity testing.
Visually inspect the earthing system for any signs of damage or corrosion.
Measure the resistance of the earthing system using a earth tester to ensure it is within acceptable limits.
Perform continuity testing to ensure all components of the earthing system are properly connected.
Check for proper bonding bet...
posted on 4 May 2019
I applied via Approached by Company and was interviewed in Oct 2018. There were 5 interview rounds.
posted on 30 Apr 2023
I applied via Recruitment Consulltant and was interviewed in Oct 2022. There were 2 interview rounds.
DC current is the flow of electric charge in a constant direction.
DC stands for Direct Current.
It is the type of electric current that flows in a single direction.
DC current is produced by sources such as batteries, fuel cells, and solar cells.
It is commonly used in electronic devices and power transmission systems.
Unlike AC (Alternating Current), DC current does not change its direction over time.
DC current is the flow of electric charge in a single direction.
DC stands for Direct Current
It is produced by sources such as batteries, fuel cells, and solar cells
DC current is used in electronic devices such as computers, televisions, and radios
DC current is measured in amperes (A)
I applied via Approached by Company and was interviewed in Oct 2022. There were 3 interview rounds.
In the company how to work and how part is made in the company and which part is made by company.
The test giving normally and honestly.I also give test honestly and carefully as well as brainly
I applied via TATASTEEL and was interviewed in Aug 2022. There were 2 interview rounds.
Logistics is the process of planning, implementing, and controlling the efficient flow and storage of goods, services, and information.
Logistics involves activities such as transportation, warehousing, inventory management, and order fulfillment.
It ensures that the right products are delivered to the right place, at the right time, and in the right quantity.
Logistics plays a crucial role in supply chain management and ...
based on 5 interviews
Interview experience
based on 20 reviews
Rating in categories
Territory Sales Incharge
457
salaries
| ₹0 L/yr - ₹0 L/yr |
Assistant Manager
274
salaries
| ₹0 L/yr - ₹0 L/yr |
Sales Officer
182
salaries
| ₹0 L/yr - ₹0 L/yr |
Area Sales Manager
179
salaries
| ₹0 L/yr - ₹0 L/yr |
Executive
176
salaries
| ₹0 L/yr - ₹0 L/yr |
Hindustan Unilever
ITC
Godrej Industries Group
Marico