Filter interviews by
Clear (1)
I applied via Recruitment Consulltant and was interviewed before May 2022. There were 2 interview rounds.
I have handled testing of various electrical equipment including transformers, switchgears, motors, generators, and control panels.
Testing of transformers for insulation resistance, winding resistance, turns ratio, and polarity
Testing of switchgears for insulation resistance, contact resistance, and operation
Testing of motors for insulation resistance, winding resistance, and no-load and load testing
Testing of generato...
I was interviewed before Aug 2016.
Switchgear is a combination of electrical disconnect switches, fuses, or circuit breakers used to control, protect, and isolate electrical equipment.
Switchgear is a general term for a collection of devices used to control, protect, and isolate electrical equipment.
Circuit breakers are a type of switchgear that automatically interrupts the flow of electric current when a fault is detected.
Switchgear can include disconne...
The interface between transformer and switch gears is the electrical connection and communication between the two components.
The transformer and switch gears are connected through electrical cables or busbars.
The switch gears control the flow of electrical power to and from the transformer.
The switch gears may include circuit breakers, relays, and protective devices.
The interface ensures proper coordination and protect...
The value of IBL of Transformer oil is the Insulating Breakdown Level.
IBL is a measure of the dielectric strength of transformer oil.
It indicates the maximum voltage that the oil can withstand before it breaks down and loses its insulating properties.
The IBL value is important for ensuring the safe and reliable operation of transformers.
Regular testing of transformer oil is necessary to monitor the IBL and detect any p...
I am currently earning $80,000 and I am looking for a salary in the range of $90,000 to $100,000.
My current salary is $80,000.
I am expecting a salary in the range of $90,000 to $100,000.
I am open to negotiation based on the overall compensation package.
Yes, I am ready for re-location.
I am open to moving to a new location for the right opportunity.
I have experience working in different cities and adapting to new environments.
I am willing to relocate to further my career and gain new experiences.
I understand the challenges that come with re-location and I am prepared to face them.
I have a flexible mindset and can easily adjust to new surroundings.
Negotiation is typically done before arrival to finalize terms and conditions.
Negotiations are usually conducted before the candidate arrives to ensure all terms are agreed upon in advance.
It is important to have a clear understanding of the offer and terms before accepting the job.
Discussing and finalizing details beforehand can help avoid misunderstandings or conflicts later on.
Top trending discussions
I applied via Recruitment Consulltant and was interviewed before May 2022. There were 3 interview rounds.
IS codes are Indian Standards codes used for standardization of products, processes, and services.
IS 456:2000 - Code of practice for plain and reinforced concrete
IS 2062:2011 - Specification of steel for general structural purposes
IS 800:2007 - Code of practice for general construction in steel
IS 1343:2012 - Code of practice for prestressed concrete
IS 1200:Part 1:1992 - Method of measurement of building and civil engin...
Load cases in STAAD are used for qualification purposes to ensure structural safety.
Load cases are combinations of loads that a structure may experience during its lifetime.
Qualification load cases are used to ensure that the structure can withstand the maximum expected loads.
Examples of load cases include dead load, live load, wind load, seismic load, and temperature load.
Each load case is analyzed separately to deter...
Stiffness value refers to the resistance of an object to deformation under an applied force.
Stiffness is a measure of how much force is required to deform an object.
It is often used in engineering to describe the rigidity of a material or structure.
Stiffness can be calculated using Hooke's Law, which states that the force required to deform an object is proportional to the displacement.
For example, a steel beam is stif...
I applied via Approached by Company
I applied via Walk-in and was interviewed in Nov 2023. There were 3 interview rounds.
Surging is a phenomenon in which a system experiences rapid and temporary increases in pressure or flow rate.
Surging can occur in various systems such as pipelines, compressors, pumps, and turbines.
It is often caused by sudden changes in demand, equipment malfunctions, or improper system design.
Surging can lead to damage to equipment, reduced efficiency, and safety hazards.
Examples include water hammer in pipelines and
Froude number is a dimensionless number used to quantify the influence of gravity on fluid flow.
Froude number is defined as the ratio of inertia force to gravitational force in a fluid flow.
It is used to determine the type of flow (subcritical, critical, or supercritical) in open channel flow.
Froude number is calculated as Fr = V / sqrt(g * d), where V is velocity, g is acceleration due to gravity, and d is depth of fl
Weeping is the process of fluid leaking out of a solid material, often due to damage or excess moisture.
Weeping can occur in materials such as wood, concrete, and metal.
It is often a sign of structural damage or deterioration.
Examples include water weeping from a crack in a wall or oil weeping from a car engine.
Weeping can also refer to the shedding of tears in humans and animals.
A basic PFD of a WTP plant including feed quality and sensors.
Include feed quality parameters such as turbidity, pH, temperature, and flow rate
Include sensors for monitoring parameters like chlorine levels, pressure, and conductivity
Show the flow of water through various treatment processes like coagulation, flocculation, sedimentation, filtration, and disinfection
Process checks in line testing of a 6inch dia pigging line and associated calculations
Pressure testing to ensure integrity of the line
Flow testing to check for blockages or restrictions
Calibration of pigging equipment for accurate results
Calculations involve pressure drop, flow rate, and pigging efficiency
Recording and analyzing data for future reference
I applied via Company Website and was interviewed in Oct 2021. There were 3 interview rounds.
I applied via Approached by Company and was interviewed before Feb 2021. There were 2 interview rounds.
posted on 5 May 2024
based on 1 interview
Interview experience
based on 6 reviews
Rating in categories
Architect
9
salaries
| ₹0 L/yr - ₹0 L/yr |
Electrical Engineer
8
salaries
| ₹0 L/yr - ₹0 L/yr |
BIM Modeller
7
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Architect
6
salaries
| ₹0 L/yr - ₹0 L/yr |
Electrical Project Engineer
5
salaries
| ₹0 L/yr - ₹0 L/yr |
TCE
Mecon
L&T Technology Services
AECOM