Add office photos
Filter interviews by
Power Mech Projects Interview Questions, Process, and Tips
Top Power Mech Projects Interview Questions and Answers
- Q1. All type contractors in use electrical panelasked in Electrical Supervisor interview
- Q2. Why use 4-20 ma why do not 0-20 maasked in Senior Instrumentation Technician interview
- Q3. What type gear angel 90 deeriasked in MW Fitter interview
Power Mech Projects Interview Experiences
92 interviews found
I applied via Walk-in and was interviewed in Sep 2022. There were 2 interview rounds.
(2 Questions)
- Q1. Work related, maintenance, Management
- Q2. REPORTING, TEAM MANAGEMENT
Interview Preparation Tips
Senior Engineer Mechanical Interview Questions asked at other Companies
(1 Question)
- Q1. Generator protection Transformer protection Single line electrical diagram Switchyard single line diagram HT and LT breaker closing coil and tripping coil
(1 Question)
- Q1. Generator protection , transformer protection
- Ans. Generator :- stator short circuit , earth fault ,rotor earth fault, low forword power , reverse power flow, low frequency,over frequency
Interview Preparation Tips
Electrical Engineer Interview Questions asked at other Companies
1st round is conducted with simple aptitude and civil basic queations. By getting above of 25 we can qualify the first round out of 40 marks
(1 Question)
- Q1. They asked me basic civil subject queations.
(1 Question)
- Q1. Will u agree to relocate all over the india.
Interview Preparation Tips
Engineer Trainee Interview Questions asked at other Companies
Ranjith Rithanya
Selected
I applied via Referral and was interviewed before Jun 2023. There was 1 interview round.
(2 Questions)
- Q1. Target mean strength of M-35 Grade concrete
- Ans.
Target mean strength of M-35 Grade concrete is 35 MPa.
The target mean strength of M-35 Grade concrete is 35 MPa.
M-35 Grade concrete is designed for structural applications requiring high strength.
Quality control measures should be in place to ensure the concrete meets the target strength.
- Q2. What is the soil compaction percentage to be achieved in Embankment
- Ans.
Soil compaction percentage in embankment typically ranges from 90% to 95% depending on the type of soil and project specifications.
Soil compaction percentage in embankment is usually between 90% to 95%
The exact percentage may vary based on the type of soil being compacted
Project specifications and requirements will dictate the specific compaction percentage to be achieved
QA QC Engineer Interview Questions asked at other Companies
Power Mech Projects interview questions for popular designations
Prasanta Paul
Selected
I applied via Approached by Company and was interviewed before Jun 2023. There was 1 interview round.
(2 Questions)
- Q1. What is your previous experience
- Q2. What is your salary experience
Chemist Interview Questions asked at other Companies
Get interview-ready with Top Power Mech Projects Interview Questions
Gaurav yadav
I applied via Walk-in and was interviewed in Apr 2022. There were 3 interview rounds.
(2 Questions)
- Q1. In TRANSFORMER PROTECTION
- Ans.
Transformer protection is essential to prevent damage and ensure safe operation.
The protection system should detect and isolate faults quickly.
Common protection methods include overcurrent, differential, and distance protection.
Proper maintenance and testing of protection equipment is crucial.
Examples of transformer protection devices include Buchholz relays, pressure relief devices, and temperature sensors.
- Q2. What is Master trip relay
- Ans.
Master trip relay is a protective relay that trips all the circuit breakers in a power system in case of a fault.
It is used to protect the power system from damage due to faults
It is connected to all the circuit breakers in the system
It operates when a fault is detected and trips all the circuit breakers simultaneously
It is an important component of the protection system in power plants and substations
(3 Questions)
- Q1. Event and DR IN SCADA OPRATION
- Ans.
Event and DR are crucial in SCADA operation for ensuring system reliability and continuity.
Event refers to any occurrence that requires attention or action, such as a fault or alarm.
DR (Disaster Recovery) is a plan for restoring normal system operation in case of a catastrophic event.
SCADA systems rely on event and DR management to ensure uninterrupted operation and prevent downtime.
Examples of events in SCADA operatio...
- Q2. In Line protection which relay use
- Ans.
Line protection relays are used for protecting transmission lines from faults.
Line protection relays are used to detect faults in transmission lines and isolate them from the system.
These relays can be of different types such as distance, differential, and directional relays.
Distance relays measure the impedance of the line and trip when the impedance falls below a certain threshold.
Differential relays compare the curr...
- Q3. GIS SUBSTATION SWITCHGEAR OPRATION PROCESS
Interview Preparation Tips
Skills evaluated in this interview
JN Engineer Interview Questions asked at other Companies
Jobs at Power Mech Projects
Selected
(1 Question)
- Q1. Good support for
Not conducted the aptitude test
(2 Questions)
- Q1. Work experience
- Q2. Present working
(1 Question)
- Q1. Land acquisition
(1 Question)
- Q1. Back ground verification
(1 Question)
- Q1. How much expected
(2 Questions)
- Q1. Tell me something about your self.
- Q2. Tell me about your qualification
Interview Preparation Tips
Admin Executive Interview Questions asked at other Companies
Junior Electrical Maintenance Engineer Interview Questions & Answers
Anonymous
posted on 28 Oct 2022
I applied via Referral and was interviewed in Sep 2022. There were 2 interview rounds.
(2 Questions)
- Q1. Lt motor and HT motors and all electrical safety device
- Q2. What is your current job and what are you doing
Interview Preparation Tips
Junior Electrical Maintenance Engineer Interview Questions asked at other Companies
I applied via Walk-in and was interviewed in Mar 2022. There were 2 interview rounds.
(3 Questions)
- Q1. Belt utilisation formula
- Ans.
Belt utilisation formula calculates the percentage of time a conveyor belt is in use.
Belt utilisation formula = (total operating time / total time) x 100%
Total operating time includes the time the belt is running and the time it is loaded but not running
Total time includes the operating time plus any downtime for maintenance or repairs
Example: If a conveyor belt runs for 8 hours a day and is loaded for 6 hours, the bel...
- Q2. What is Belt Sefty divice
- Ans.
A Belt Safety Device is a safety mechanism that prevents a conveyor belt from running when it's not supposed to.
It is used in conveyor systems to prevent accidents and injuries.
It can detect if the belt is misaligned, torn, or broken.
It can also detect if there is an object on the belt that shouldn't be there.
Examples of Belt Safety Devices include emergency stop switches, pull cords, and belt sway switches.
- Q3. What is Belt capacity
- Ans.
Belt capacity refers to the maximum amount of material that a conveyor belt can handle.
Belt capacity is measured in tons per hour or cubic meters per hour.
It depends on the width and speed of the belt, as well as the characteristics of the material being transported.
For example, a belt with a width of 1 meter and a speed of 2 meters per second may have a capacity of 1000 tons per hour for coal, but only 500 tons per ho
Interview Preparation Tips
skills and continue to the team effort to achieve group goals and at the same time endeavour to acquire new
and sophisticated skills as they come.
DCS Operations Engineer Interview Questions asked at other Companies
Top trending discussions
Power Mech Projects Interview FAQs
The duration of Power Mech Projects interview process can vary, but typically it takes about less than 2 weeks to complete.
Tell us how to improve this page.
Power Mech Projects Interviews By Designations
- Power Mech Projects Electrical Engineer Interview Questions
- Power Mech Projects Engineer Interview Questions
- Power Mech Projects Mechanical Engineer Interview Questions
- Power Mech Projects Senior Engineer Interview Questions
- Power Mech Projects Safety Officer Interview Questions
- Power Mech Projects Assistant Manager Interview Questions
- Power Mech Projects Deputy Manager Interview Questions
- Power Mech Projects Engineer Trainee Interview Questions
- Show more
Interview Questions for Popular Designations
- Mechanical Engineer Interview Questions
- Engineer Interview Questions
- Electrical Engineer Interview Questions
- Senior Engineer Interview Questions
- Senior Executive Interview Questions
- Software Developer Interview Questions
- Intern Interview Questions
- Associate Software Engineer Interview Questions
- Show more
Power Mech Projects Interview Process
based on 92 interviews
Interview experience
Interview Questions from Similar Companies
Fast track your campus placements
Power Mech Projects Reviews and Ratings
based on 1.6k reviews
Rating in categories
|
Senior Engineer
411
salaries
|  ₹3 L/yr - ₹8.4 L/yr |
|
Assistant Manager
334
salaries
| ₹4.1 L/yr - ₹10 L/yr |
|
Engineer
273
salaries
| ₹2 L/yr - ₹6.9 L/yr |
|
Mechanical Engineer
242
salaries
| ₹2 L/yr - ₹6.7 L/yr |
|
Electrical Engineer
218
salaries
| ₹2 L/yr - ₹7.5 L/yr |
Thermax Limited
BGR Energy Systems
Larsen & Toubro Limited
Kalpataru Projects International
- Home >
- Interviews >
- Power Mech Projects Interview Questions
