Kuttalam Gas Turbine Power Station Interview Questions and Answers

The percentage of steel in a pile varies depending on the type and design of the pile.

• The percentage of steel in a pile can range from 0% to over 90%.

• The type of pile (e.g. steel, concrete, timber) and its design (e.g. diameter, length, wall thickness) determine the percentage of steel.

• Steel piles typically have a higher percentage of steel than other types of piles.

• The percentage of steel in a pile can also affect its

Pile built-up above cut off level as per IS code

• IS code specifies the maximum allowable pile length above cut off level

• Pile length above cut off level should not exceed 3 times the pile diameter

• Built-up pile above cut off level can cause structural instability and failure

Vertical tolerance for piles as per IS code

• As per IS 2911-1:2010, the vertical tolerance for piles is +/- 25mm

• This tolerance is applicable for both driven and cast-in-situ piles

• The tolerance is measured at the top of the pile and at intervals of 3m along the length

• If the deviation exceeds the tolerance limit, the pile may need to be rejected or remedial measures taken

Pile concrete consumption tolerance depends on various factors.

• Pile diameter and length

• Concrete mix design

• Placement method

• Quality control measures

• Environmental conditions

• Tolerance typically ranges from 5-10% of estimated consumption

• Regular monitoring and adjustment of concrete consumption is necessary

Unit weight of steel is 7850 kg/m³

• The unit weight of steel is the weight of a specific volume of steel

• It is measured in kilograms per cubic meter (kg/m³)

• The unit weight of steel is 7850 kg/m³

• This value may vary slightly depending on the composition and manufacturing process of the steel

To start new dealer scouting, research the market, identify potential dealers, and reach out to them with a compelling pitch.

• Research the market to identify potential dealers

• Create a list of potential dealers and prioritize them based on their fit with your product

• Reach out to potential dealers with a compelling pitch that highlights the benefits of partnering with your company

• Follow up with potential dealers to build ...read more

To increase MS, focus on building strong relationships with customers, providing excellent customer service, and offering competitive pricing.

• Develop a deep understanding of the market and customer needs

• Offer personalized solutions and recommendations

• Provide ongoing support and follow-up to ensure customer satisfaction

• Regularly analyze and adjust pricing to remain competitive

• Invest in marketing and advertising to incre...read more

1st Angle projection symbol is a square with a dot inside while 3rd angle projection symbol is a square with three dots outside.

• 1st Angle projection is commonly used in Europe and Asia while 3rd angle projection is commonly used in North America.

• The symbol is used to indicate the orientation of the object being projected in relation to the viewing plane.

• In 1st Angle projection, the object is placed between the viewer a...read more

2D drawings are flat representations of a part or assembly, while 3D drawings show the part or assembly in three dimensions.

• 2D drawings are typically used for simpler parts or assemblies

• 3D drawings are more complex and allow for better visualization of the part or assembly

• 2D drawings show only two views, while 3D drawings can show multiple views and angles

• 3D drawings can be used for simulations and testing

• 2D drawings a...read more

2 stroke engines have a power stroke in every revolution, while 4 stroke engines have a power stroke in every other revolution.

• 2 stroke engines have a simpler design and are lighter than 4 stroke engines.

• 4 stroke engines are more fuel efficient and emit less pollution than 2 stroke engines.

• 2 stroke engines are commonly used in small power tools and some motorcycles, while 4 stroke engines are used in cars, trucks, and ...read more

Two stroke and four stroke engines differ in their working cycles and efficiency.

• Two stroke engines complete a power cycle in two strokes of the piston, while four stroke engines complete it in four strokes.

• Two stroke engines have a simpler design and are lighter, but are less fuel efficient and produce more emissions.

• Four stroke engines have separate intake, compression, power, and exhaust strokes, resulting in better...read more

Diesel engines and petrol engines differ in fuel type, ignition process, compression ratio, and efficiency.

• Fuel type: Diesel engines use diesel fuel, while petrol engines use gasoline.

• Ignition process: Diesel engines use compression ignition, while petrol engines use spark ignition.

• Compression ratio: Diesel engines have higher compression ratios than petrol engines.

• Efficiency: Diesel engines are generally more fuel-eff...read more

A turbocharger is a device that increases the efficiency and power output of an internal combustion engine.

• A turbocharger uses exhaust gases to drive a turbine, which in turn drives a compressor to force more air into the engine.

• By increasing the amount of air entering the engine, a turbocharger allows more fuel to be burned, resulting in increased power.

• Turbochargers are commonly used in diesel engines and high-perfor...read more

Collective bargaining is a process of negotiation between employers and employees, usually through their respective representatives, to determine the terms and conditions of employment.

• It involves a group of employees bargaining with their employer for better wages, benefits, and working conditions

• The process is usually facilitated by a union or other employee representative

• The goal is to reach a mutually beneficial ag...read more