Filter interviews by
Control points & TBM are located at specific coordinates on the site.
Control points are established to provide a reference for surveying measurements.
TBM (Temporary Bench Mark) is a point of known elevation used as a reference for leveling.
The location of control points and TBM are determined based on the project requirements and site conditions.
They are typically marked with a stake or monument and recorded in a surve
Yes, I am familiar with columns and core-wall offset marking.
Columns and core-walls are marked with a specific offset to ensure proper alignment and placement.
This marking is usually done using a chalk line or laser level.
The offset distance is determined by the project specifications and can vary depending on the size and location of the columns and core-walls.
Proper offset marking is crucial for the structural integr...
Level shifting is the process of converting a signal from one voltage level to another.
Level shifting can be done using voltage dividers, operational amplifiers, or digital logic circuits.
Voltage dividers are used to reduce the voltage level of a signal.
Operational amplifiers can be used to amplify or attenuate a signal to the desired level.
Digital logic circuits can be used to convert a signal from one logic level to ...
Control points are shifted vertically using plumb bobs and laser levels.
Control points are established on the ground floor using surveying instruments.
Plumb bobs and laser levels are used to transfer the control points vertically to the next floor.
The control points are re-established on the next floor using the transferred points as reference.
This process is repeated for each floor of the building.
The accuracy of the ...
Yes, Resection is a surveying technique used to determine the location of an unknown point by sighting in on known points.
Resection involves using at least two known points and measuring the angles between them and the unknown point.
The intersection of these angles gives the location of the unknown point.
Resection is commonly used in land surveying and mapping.
It can also be used in navigation and military applications
Yes, travees are used in surveying to mark points on the ground.
Travees are wooden or metal stakes used to mark points on the ground during surveying.
They are often used to mark the corners of a property or the location of a proposed structure.
Travees can also be used to mark the location of underground utilities or other features.
Surveyors use a variety of tools and techniques to accurately measure and mark points on ...
Yes, I am proficient in AutoCAD.
I have experience using AutoCAD for creating and editing engineering drawings.
I am familiar with various AutoCAD commands and tools.
I have used AutoCAD to create 2D and 3D models for surveying projects.
I am able to import and export data from AutoCAD to other software programs.
I am comfortable working with different file formats in AutoCAD.
Top trending discussions
I applied via Walk-in and was interviewed before Feb 2022. There were 3 interview rounds.
I applied via Referral and was interviewed in Dec 2023. There was 1 interview round.
Hydration is the process of providing adequate fluids to the body to maintain proper function.
Hydration is essential for overall health and well-being
It helps regulate body temperature, transport nutrients, and remove waste
Drinking water, consuming fruits and vegetables, and electrolyte-rich beverages are ways to stay hydrated
I applied via Naukri.com and was interviewed before Apr 2023. There were 3 interview rounds.
posted on 22 Feb 2022
Bus bar schemes are different ways of connecting bus bars in power systems.
Single bus bar scheme
Double bus bar scheme
Main and transfer bus bar scheme
Ring bus bar scheme
Breaker and a half scheme
Mesh bus bar scheme
The equipment sequence for any line bay starts with the circuit breaker and ends with the transformer.
The circuit breaker is the first equipment in the sequence.
Next comes the isolator switch.
After that, the earth switch is operated.
Then the line disconnector is opened.
Finally, the transformer is disconnected from the line.
The sequence is reversed when the line bay is put back into service.
I applied via Company Website and was interviewed before Jan 2022. There were 3 interview rounds.
Designing a floating head assembly involves considering various factors such as material selection, sealing mechanisms, and thermal expansion.
Select appropriate materials for the floating head assembly based on the application requirements.
Design effective sealing mechanisms to prevent leakage and ensure proper functioning.
Consider thermal expansion and contraction to accommodate temperature variations.
Ensure proper al...
H2S service for pressure vessel refers to the use of hydrogen sulfide in a pressure vessel.
H2S service involves the handling and containment of hydrogen sulfide gas in a pressure vessel.
Pressure vessels used in H2S service must be designed and constructed to withstand the corrosive effects of hydrogen sulfide.
Special materials and coatings may be required to prevent hydrogen sulfide from corroding the pressure vessel.
R...
Gaskets are mechanical seals used to prevent leakage between two surfaces. There are various types of gaskets available.
Sheet gaskets
Spiral wound gaskets
Ring gaskets
Metallic gaskets
Rubber gaskets
Cork gaskets
Non-asbestos gaskets
Assistant Engineer
58
salaries
| ₹2.3 L/yr - ₹4.6 L/yr |
Senior Engineer
57
salaries
| ₹5 L/yr - ₹9.5 L/yr |
Assistant Manager
42
salaries
| ₹6.1 L/yr - ₹16 L/yr |
Engineer
38
salaries
| ₹3 L/yr - ₹8 L/yr |
HSE Engineer
30
salaries
| ₹2.4 L/yr - ₹8 L/yr |
Alstom Transportation
Saint-Gobain
AECOM
AtkinsRealis