Filter interviews by
I applied via Referral and was interviewed before Nov 2020. There were 5 interview rounds.
WAH stands for Working at Heights. It refers to the practice of working in elevated areas and the safety standards associated with it.
WAH is an acronym for Working at Heights.
It involves working in elevated areas such as rooftops, scaffolding, or ladders.
The WAH standard includes guidelines and regulations to ensure the safety of workers.
It emphasizes the use of fall protection equipment like harnesses, guardrails, and...
Scaffolding is a temporary structure used to support workers and materials during construction or maintenance of buildings or structures.
Scaffolding is typically made of metal or wood and consists of platforms, braces, and supports.
It is used to provide a safe working platform for workers at heights.
Scaffolding is commonly used in construction, maintenance, and repair of buildings, bridges, and other structures.
Example...
MSDS stands for Material Safety Data Sheet. It is a document that provides information about the potential hazards and safe handling of a chemical substance.
MSDS is a comprehensive document that contains detailed information about a chemical substance, including its physical and chemical properties, potential hazards, and safety precautions.
It is typically provided by the manufacturer or supplier of the chemical and is...
Method of statement is a written document that outlines the steps and procedures to be followed for a specific task or project.
Method of statement is used in industries such as construction, engineering, and manufacturing.
It includes details such as the scope of work, materials required, equipment needed, and safety precautions.
The method of statement is usually prepared by the contractor or project manager and submitt...
The construction field in India follows various rules and regulations to ensure safety and compliance.
The Building and Other Construction Workers Act, 1996
The Construction and Demolition Waste Management Rules, 2016
The National Building Code of India, 2016
The Occupational Safety, Health and Working Conditions Code, 2020
The Environment Protection Act, 1986
The Water (Prevention and Control of Pollution) Act, 1974
The Air
A lifeline is a safety line used to prevent falls and injuries in high-risk work environments.
Lifelines are typically made of rope or cable and are attached to a secure anchor point.
Workers wear a harness that is connected to the lifeline, allowing them to move freely while still being protected from falls.
Lifelines should be inspected regularly and replaced if any damage is found.
OSHA has specific regulations regardin...
TPI stands for Third Party Inspection. It is conducted by an independent party to ensure compliance with standards and regulations.
TPI is a process where an external party assesses the quality and safety of a product or service
It is commonly used in industries such as manufacturing, construction, and oil and gas
TPI helps to verify that the product or service meets the required specifications and standards
The frequency ...
Lifting gears are equipment used to lift heavy loads. They require regular maintenance and checking to ensure safety.
Lifting gears include cranes, hoists, slings, and shackles.
Maintenance should be done regularly to ensure proper functioning and safety.
Checking standards include load testing, visual inspections, and non-destructive testing.
Proper training and certification is required for operators and inspectors.
Any d...
Color coding is a system of assigning colors to objects or areas to indicate their purpose or level of hazard.
Color coding is commonly used in workplaces to improve safety and organization.
Different colors can be used to indicate different types of hazards, such as red for fire hazards or yellow for caution.
Color coding can also be used to designate specific areas for certain activities, such as green for first aid sta...
HIRA and JSEA are risk assessment tools used in occupational health and safety.
HIRA stands for Hazard Identification and Risk Assessment. It is a systematic process of identifying potential hazards and evaluating the associated risks.
JSEA stands for Job Safety and Environmental Analysis. It is a tool used to identify potential hazards and assess the risks associated with a specific job or task.
Both HIRA and JSEA are im...
PTW stands for Permit to Work. It is a formal written system used to control high-risk activities.
PTW is used to ensure that all necessary safety measures are taken before starting a high-risk activity.
It involves a written permit that must be obtained before starting the work.
The permit outlines the hazards associated with the work and the precautions that must be taken to mitigate those hazards.
PTW is commonly used i...
Top trending discussions
posted on 29 Dec 2020
Dominant frequencies of 1×, 2×, and 3× RPM in the spectrum indicate faults in rotating equipment.
1× RPM indicates misalignment or unbalance
2× RPM indicates gear or bearing faults
3× RPM indicates resonance or coupling issues
Diagnosing abnormal sound from mill motor without vibration analyzer
Check for any visible signs of damage or wear on the motor and surrounding components
Listen for any changes in the sound when the motor is turned off and on again
Check the lubrication system and oil levels
Inspect the belts and pulleys for any signs of wear or damage
Consult with experts or manufacturers for further guidance
Centrifugal pump performance characteristics refer to the relationship between flow rate, head, power, and efficiency.
Flow rate is the volume of fluid that passes through the pump per unit time.
Head is the energy added to the fluid by the pump and is proportional to the pressure increase.
Power is the energy required to operate the pump and is proportional to the flow rate and head.
Efficiency is the ratio of the energy ...
HP and KW are units of power measurement, with HP being the imperial unit and KW being the metric unit.
HP stands for horsepower and is commonly used in the United States and other countries that use the imperial system of measurement.
KW stands for kilowatt and is commonly used in countries that use the metric system of measurement.
1 horsepower is equal to 0.7457 kilowatts.
The relationship between HP and KW is important...
I applied via Recruitment Consulltant and was interviewed in Sep 2023. There was 1 interview round.
I applied via Approached by Company and was interviewed before Nov 2022. There were 3 interview rounds.
I have extensive experience in global procurement process, supplier relationship management, end to end procurement, and cross functional collaboration.
Successfully managed global procurement process by identifying cost-saving opportunities and negotiating contracts with suppliers.
Faced challenges in supplier relationship management due to communication barriers, but resolved them by establishing regular meetings and c...
To tackle problems in procurement, it is important to identify root causes, establish clear communication channels, implement efficient processes, and continuously monitor performance.
Identify root causes of procurement problems such as supplier issues, inventory management issues, or process inefficiencies.
Establish clear communication channels with suppliers, stakeholders, and internal teams to ensure transparency an...
Understanding of sourcing goods and services from global markets.
Knowledge of international trade regulations and tariffs
Ability to identify and evaluate global suppliers
Experience in negotiating contracts with overseas vendors
Awareness of currency exchange rates and their impact on procurement costs
We work with a variety of suppliers globally to ensure a diverse and reliable supply chain.
We have partnerships with suppliers in Asia, Europe, and North America.
Our suppliers range from small local businesses to large multinational corporations.
We prioritize suppliers who share our commitment to sustainability and ethical practices.
I applied via Naukri.com and was interviewed in Mar 2022. There were 2 interview rounds.
I applied via Company Website and was interviewed in Sep 2021. There was 1 interview round.
I have extensive expertise in DFIG generators and their applications in various industries.
I have worked on the design and development of DFIG generators for wind turbines.
I have experience in troubleshooting and maintenance of DFIG generators.
I am familiar with the control systems used in DFIG generators.
I have knowledge of the latest advancements in DFIG generator technology.
I have worked on projects involving the in...
I have extensive experience working with various systems and machines in major projects.
Implemented ERP system for streamlining operations
Managed deployment of CRM system for customer relationship management
Led team in upgrading manufacturing machines for increased efficiency
I applied via Company Website and was interviewed before May 2021. There was 1 interview round.
Impedance is the measure of opposition to the flow of electric current in a circuit. DGR fundamental refers to the Dielectric Withstand Voltage test.
Impedance is measured in ohms and is the combination of resistance, capacitance, and inductance in a circuit.
DGR fundamental is a test to determine the maximum voltage a material can withstand without breaking down.
Basics of impedance include understanding the relationship...
I applied via Naukri.com and was interviewed before Jan 2022. There were 2 interview rounds.
Quality tools for analysis include Pareto charts, fishbone diagrams, scatter plots, and control charts.
Pareto charts help identify the most significant factors affecting quality
Fishbone diagrams help identify the root cause of a problem
Scatter plots help identify correlations between variables
Control charts help monitor and control a process over time
based on 10 reviews
Rating in categories
Deputy Manager
222
salaries
| ₹5 L/yr - ₹17.5 L/yr |
Manager
165
salaries
| ₹5.8 L/yr - ₹24.1 L/yr |
Senior Engineer
157
salaries
| ₹4 L/yr - ₹12 L/yr |
Engineer
85
salaries
| ₹3 L/yr - ₹8.4 L/yr |
Senior Manager
63
salaries
| ₹10 L/yr - ₹32 L/yr |
Vestas
Dhoot Transmission
Hitachi Energy
Siemens Energy