Bedmutha Group Interview Questions and Answers

Piles are used in construction to transfer loads from a structure to a stronger layer of soil or rock below the surface.

• Types of piles include driven piles, bored piles, and screw piles.

• Piles are provided to support structures on weak or compressible soil, to resist uplift forces, or to provide lateral support.

• The diameter of a pile is determined based on the load it needs to support and the soil conditions.

• LVUP (Large...read more

I don't have the available data to answer this question.

• Sorry, I don't have access to the current data on the number of PTR engaged at BT laying.

• I suggest checking with the relevant department or team for the latest information.

The crusher make model and process of crushing depend on the type of material being crushed.

• The make and model of the crusher will vary depending on the application and material being crushed.

• The process of crushing also varies depending on the material and desired output size.

• For example, a jaw crusher may be used for primary crushing of hard rock, while a cone crusher is more suitable for secondary or tertiary crushi...read more

Cutting 150 hill in 60 degree slope requires careful planning and execution.

• Conduct a thorough survey of the area to determine the best approach

• Use heavy machinery such as excavators and bulldozers to remove the hill

• Ensure safety measures are in place to prevent accidents

• Consider environmental impact and take necessary precautions

• Consult with experts in the field for advice and guidance

Protection in 150m height can be achieved through various means.

• Use of safety harness and fall protection equipment

• Installation of guardrails and safety nets

• Implementation of a comprehensive safety plan

• Regular inspection and maintenance of equipment

• Training and education of workers on safety procedures

The grade of bitumen used in hill areas depends on the temperature and altitude of the region.

• The higher the altitude, the harder the bitumen used.

• The temperature also plays a crucial role in determining the grade of bitumen.

• For example, in colder regions, a harder grade of bitumen is used to prevent cracking and deformation.

• In contrast, in warmer regions, a softer grade of bitumen is used to prevent rutting and deform

Concrete in minimum temperature requires proper mix design, curing, and protection from freezing.

• Use a mix design with low water-cement ratio and proper amount of cement and admixtures.

• Ensure proper curing by covering the concrete with blankets or insulating materials.

• Protect the concrete from freezing by using heaters or insulating blankets.

• Monitor the temperature of the concrete and the environment during and after p...read more

Cavity in tunnels can be protected by using various methods.

• Waterproofing the tunnel lining

• Using grouting techniques to fill the cavity

• Installing drainage systems to prevent water accumulation

• Regular inspections and maintenance

• Using shotcrete to reinforce the tunnel lining

• Applying rock bolts to stabilize the surrounding rock

• Using steel ribs to support the tunnel lining

Cycle time in tunnel refers to the time taken to complete one cycle of a process or operation within the tunnel.

• Cycle time can vary depending on the type of tunnel and the process being carried out.

• For example, in a transportation tunnel, cycle time may refer to the time taken for a vehicle to enter and exit the tunnel.

• In a manufacturing tunnel, cycle time may refer to the time taken to complete one production cycle.

• Ef...read more

NATM stands for New Austrian Tunneling Method, a technique used in underground construction.

• NATM is a tunneling method that involves excavating the tunnel while providing support to the surrounding rock mass.

• It was developed in Austria in the 1950s and has since been used in various tunneling projects worldwide.

• NATM involves the use of shotcrete, rock bolts, and steel ribs to support the tunnel walls and roof.

• Examples ...read more

The frequency of drilling holes in the face depends on the specific project requirements and geological conditions.

• The number of holes drilled in the face will vary depending on the project's needs and the geological conditions of the site.

• Factors such as the type of rock, the size of the excavation, and the equipment being used will all influence the frequency of drilling.

• It is important to carefully plan and execute ...read more

Proholes is not a known term in engineering. No data available.

Drain holes are necessary to prevent water accumulation and damage to structures or equipment.

• Drain holes allow water to escape from areas where it can cause damage or corrosion.

• They are commonly used in outdoor furniture, boats, and buildings to prevent water accumulation.

• Drain holes can also be used in machinery to prevent damage from water or other liquids.

• Proper placement and size of drain holes is important to ens

The amount of accelerator used in shotcrete depends on various factors.

• The type of accelerator used affects the amount required.

• The desired strength and setting time also play a role.

• The ambient temperature and humidity can affect the amount needed.

• Typically, 1-5% of the cement weight is used as accelerator.

• The manufacturer's recommendations should be followed for best results.