Upload Button Icon Add office photos

Filter interviews by

ATS Group Senior Civil Engineer Interview Questions, Process, and Tips

Updated 28 Nov 2022

ATS Group Senior Civil Engineer Interview Experiences

1 interview found

I applied via Walk-in and was interviewed before Nov 2021. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(5 Questions)

  • Q1. What is developement lengh
  • Ans. 

    Development length is the minimum length of reinforcement required to transfer stress from reinforcing bar to concrete.

    • It is the length of the bar that is embedded in concrete

    • It is required to ensure that the reinforcing bar develops its full strength

    • It depends on the diameter of the bar, the strength of the concrete, and the bond between the bar and the concrete

    • It is important to calculate the development length accur...

  • Answered by AI
  • Q2. What is soundness test of cement
  • Ans. 

    Soundness test of cement checks the ability of cement to retain its volume after setting.

    • Soundness test determines the presence of uncombined lime in cement.

    • It is done by mixing cement with water and gauging it with a standard consistency.

    • The mixture is then made into a pat and kept in water for 24 hours.

    • After 24 hours, the pat is removed and observed for any cracks or distortion.

    • If the pat remains sound, the cement is

  • Answered by AI
  • Q3. Zones in beam &column
  • Ans. 

    Zones in beam & column refer to different regions with varying behavior and load distribution.

    • Zones in a beam include compression zone, tension zone, and neutral axis.

    • Compression zone experiences compressive stresses, while tension zone experiences tensile stresses.

    • Neutral axis is the region where there are no stresses.

    • In a column, zones include the core and the flange.

    • The core carries most of the axial load, while the

  • Answered by AI
  • Q4. What is high strength concrete
  • Ans. 

    High strength concrete is a type of concrete with a compressive strength greater than 6,000 psi.

    • High strength concrete is typically used in high-rise buildings, bridges, and other structures that require high load-bearing capacity.

    • It is made by using a lower water-to-cement ratio, high-quality aggregates, and special admixtures.

    • The compressive strength of high strength concrete can range from 6,000 to 20,000 psi.

    • It is ...

  • Answered by AI
  • Q5. Sequence of mivan formwork
  • Ans. 

    Mivan formwork sequence involves setting up the wall panels, fixing the corner pieces, placing the slab panels, and then removing the wall panels.

    • Start by setting up the wall panels in the desired configuration

    • Fix the corner pieces to ensure proper alignment and stability

    • Place the slab panels on top of the wall panels

    • Remove the wall panels once the concrete has set

    • Repeat the process for the next level

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - ATS Rhapsody is very good project in great noida west
I learn new skills in this organisation
Good environment in this project

Interview questions from similar companies

Interview experience
5
Excellent
Difficulty level
Easy
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Walk-in and was interviewed in Jul 2023. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - HR 

(3 Questions)

  • Q1. How to execution of ms line , DI line ,HDPE line etc
  • Ans. 

    Execution of MS line, DI line, HDPE line involves proper planning, material selection, installation, and testing.

    • Plan the layout and route of the lines based on project requirements and specifications.

    • Select appropriate materials such as MS, DI, or HDPE based on factors like pressure rating, corrosion resistance, and cost.

    • Ensure proper installation of the lines including welding, jointing, and fittings.

    • Conduct pressure...

  • Answered by AI
  • Q2. Which types of your good skills
  • Q3. Your will work in all location in India
  • Ans. My answer in only mp in india
  • Answered Anonymously

Interview Preparation Tips

Interview preparation tips for other job seekers - We are advice given that only add cv that points,you do work in job .
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I appeared for an interview in Aug 2024.

Round 1 - HR 

(3 Questions)

  • Q1. Current working organization?
  • Ans. 

    I am currently working at XYZ Engineering Firm as a Senior Civil Engineer.

    • XYZ Engineering Firm

    • Senior Civil Engineer position

    • Responsibilities include project management and design work

    • Collaborating with team members and clients

  • Answered by AI
  • Q2. Current ctc?
  • Ans. 

    Current CTC is confidential and can be discussed during negotiation.

    • Current CTC is subject to company policies and confidentiality agreements.

    • It is common practice to discuss salary expectations during the interview process.

    • Candidates should be prepared to provide their current CTC if requested by the employer.

  • Answered by AI
  • Q3. Expected CTC?
Round 2 - Technical 

(3 Questions)

  • Q1. What is plastering thickness and specifications?
  • Ans. 

    Plastering thickness and specifications refer to the recommended thickness and quality standards for applying plaster on walls or ceilings.

    • Plastering thickness is typically around 12-15mm for internal walls and 15-20mm for external walls.

    • Specifications include using the right mix of plaster, ensuring a smooth finish, and allowing for proper curing time.

    • Plastering should be done in multiple layers to achieve the desired...

  • Answered by AI
  • Q2. Current work location building Footings, and column sizes?
  • Ans. 

    Currently working on building footings and column sizes at various construction sites.

    • Designing footings based on soil conditions and structural requirements

    • Calculating column sizes based on load-bearing capacity and architectural design

    • Coordinating with structural engineers and architects to ensure proper sizing and placement

    • Inspecting construction sites to verify footing and column dimensions

    • Utilizing software such a

  • Answered by AI
  • Q3. Tiles specifications?
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Walk-in and was interviewed in May 2023. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Group Discussion 

Question & Discussion about previous project, working methods,hindreces, management and other policies of previous companies.

Round 3 - HR 

(2 Questions)

  • Q1. Last & least salary released discussion.
  • Q2. Last company package.
  • Ans. 

    The last company package was competitive and included various benefits.

    • Competitive salary

    • Health insurance

    • Retirement plan

    • Paid time off

    • Performance bonuses

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Don't lose confidence at the time of interview.
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Walk-in and was interviewed in Jun 2022. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Don’t add your photo or details such as gender, age, and address in your resume. These details do not add any value.
View all tips
Round 2 - Technical 

(4 Questions)

  • Q1. What is the basics concept used for construction of Substation from start to Finish
  • Ans. 

    The basic concept for construction of a substation involves site selection, design, equipment installation, and commissioning.

    • Site selection involves identifying a suitable location for the substation based on factors such as proximity to power sources and load centers.

    • Design involves creating a plan for the substation layout, including the placement of equipment such as transformers, switchgear, and control systems.

    • Eq...

  • Answered by AI
  • Q2. What is Single Line Diagram of Substation
  • Ans. 

    Single Line Diagram of Substation is a graphical representation of electrical distribution system in a substation.

    • It shows the electrical components and their connections in a simplified manner

    • It helps in understanding the flow of power and voltage levels in the system

    • It is used for planning, designing, and maintenance of the substation

    • It includes information about transformers, circuit breakers, busbars, and other equ...

  • Answered by AI
  • Q3. What is your strength
  • Q4. If the company not provide the payment timely to the contractor, then you will conveyance the contractor for the work

Interview Preparation Tips

Interview preparation tips for other job seekers - Just keep the confidence & positive attitude. Mostly technically & management questions are asked

I applied via Naukri.com and was interviewed before May 2017. There was 1 interview round.

Interview Questionnaire 

1 Question

  • Q1. What is the density of soil in embankment layer.
  • Ans. 

    The density of soil in the embankment layer varies depending on the type of soil and compaction methods used.

    • The density of soil in the embankment layer is typically measured in terms of dry density or wet density.

    • Dry density refers to the mass of solid soil particles per unit volume of soil, while wet density includes the mass of water as well.

    • The density of soil in the embankment layer is influenced by factors such a...

  • Answered by AI

Interview Preparation Tips

General Tips: This interview was a technical one.The interview eanted to test both my knowledge and communications skills.Most of questions are related with Transportation.
Skills: Technical Knowledge(ML, Technical Knowledge(ML
Duration: <1 week

I appeared for an interview before Jul 2016.

Interview Questionnaire 

1 Question

  • Q1. Temperature of Prime coat, Tack Coat, Penetration Grade, various tests on Bitumen, asphalt works, Rolling pattern, Rolling temperature as well as Asphalt Laying temperature, densities of various compacted ...

Interview Preparation Tips

Skills: Knowledge Of Construction Practices, Construction Technology

I applied via Approached by Company and was interviewed in Apr 2022. There was 1 interview round.

Round 1 - One-on-one 

(1 Question)

  • Q1. How mutch your working experience?

Interview Preparation Tips

Interview preparation tips for other job seekers - Intrust the field architecture and construction field

I applied via LinkedIn and was interviewed in Feb 2022. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - HR 

(1 Question)

  • Q1. Tell me about yourself.
  • Ans. 

    I am a civil engineer with experience in designing and managing construction projects.

    • I have a Bachelor's degree in Civil Engineering from XYZ University.

    • I have worked on various projects including designing bridges, roads, and buildings.

    • I am skilled in using software such as AutoCAD and Revit for designing.

    • I have experience in managing construction projects and ensuring they are completed on time and within budget.

    • I a...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Thanks for the selection in SCC Infrastructure Pvt Ltd
Interview experience
5
Excellent
Difficulty level
Easy
Process Duration
2-4 weeks
Result
Not Selected

I applied via Newspaper Ad and was interviewed in Feb 2023. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. About Carriageways, Service Roads and patchwork i.e pot Holes, slippage cracks i.e alligator crack, horizontal or vertical crack, Undulating surface,rain cut, Metals beam crash barrier,Gaurd Rail or Mild s...
Round 3 - Technical 

(3 Questions)

  • Q1. Checking level of the layer
  • Q2. Testing the field dry density of the bed like Sub Grade ,GSB,WMM, DBM or BC
  • Q3. Checking the road width

Interview Preparation Tips

Interview preparation tips for other job seekers - Sir I m very hardworker employee .
I m very panchtual for my job duty and going to site daily and prepare daily progress report and also prepare monthly progress report.

ATS Group Interview FAQs

How many rounds are there in ATS Group Senior Civil Engineer interview?
ATS Group interview process usually has 2 rounds. The most common rounds in the ATS Group interview process are Resume Shortlist and Technical.
What are the top questions asked in ATS Group Senior Civil Engineer interview?

Some of the top questions asked at the ATS Group Senior Civil Engineer interview -

  1. What is soundness test of cem...read more
  2. What is high strength concr...read more
  3. What is developement le...read more

Tell us how to improve this page.

Interview Questions from Similar Companies

TCS Interview Questions
3.7
 • 10.5k Interviews
Infosys Interview Questions
3.6
 • 7.6k Interviews
Wipro Interview Questions
3.7
 • 5.6k Interviews
Tech Mahindra Interview Questions
3.5
 • 3.8k Interviews
HCLTech Interview Questions
3.5
 • 3.8k Interviews
LTIMindtree Interview Questions
3.8
 • 2.9k Interviews
Mphasis Interview Questions
3.4
 • 797 Interviews
View all
Assistant Manager
36 salaries
unlock blur

₹4.6 L/yr - ₹12.2 L/yr

Electrical Design Engineer
15 salaries
unlock blur

₹3.2 L/yr - ₹5.3 L/yr

Senior Engineer
14 salaries
unlock blur

₹4.5 L/yr - ₹10.5 L/yr

Installation & Commissioning Engineer
12 salaries
unlock blur

₹2.5 L/yr - ₹5.5 L/yr

Design Engineer
11 salaries
unlock blur

₹2.6 L/yr - ₹6.8 L/yr

Explore more salaries
Compare ATS Group with

Lea Associates South Asia

4.3
Compare

R.V.R. PROJECTS

4.0
Compare

ABCI Infrastructures

3.4
Compare

VIKRAN Engineering & Exim

4.0
Compare
Did you find this page helpful?
Yes No
write
Share an Interview