Upload Button Icon Add office photos

Vaaman Engineers

Compare button icon Compare button icon Compare

Filter interviews by

Vaaman Engineers Maintenance Engineer Interview Questions and Answers

Updated 25 Jun 2024

Vaaman Engineers Maintenance Engineer Interview Experiences

2 interviews found

Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Walk-in and was interviewed in Aug 2022. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. Explain the work you are doing in current company.
  • Q2. Any major modification done by you in the current company.

Interview Preparation Tips

Interview preparation tips for other job seekers - Be cool take your time & explain your experience confidently.

Maintenance Engineer Interview Questions & Answers

user image Akash kumar patel

posted on 25 Jun 2024

Interview experience
4
Good
Difficulty level
Hard
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Walk-in and was interviewed before Jun 2023. There were 2 interview rounds.

Round 1 - Technical 

(2 Questions)

  • Q1. Gear box changing process
  • Ans. 

    The gear box changing process involves removing the old gear box, installing a new one, and testing for proper functionality.

    • Ensure the equipment is turned off and disconnected from power source before starting the process

    • Remove any covers or guards protecting the gear box

    • Disconnect any electrical or mechanical connections to the gear box

    • Use appropriate tools to unbolt and remove the old gear box

    • Carefully install the n...

  • Answered by AI
  • Q2. Conveyor belt changing procedure
  • Ans. 

    Conveyor belt changing procedure involves shutting down the system, removing the old belt, installing the new belt, and testing the system.

    • Shut down the conveyor system and lock out/tag out the power source to prevent accidental start-up.

    • Remove any debris or material from the conveyor belt and surrounding area.

    • Loosen the tension on the belt by adjusting the take-up pulley or tensioning device.

    • Remove the old belt by unf...

  • Answered by AI
Round 2 - HR 

(2 Questions)

  • Q1. About family members
  • Q2. Relocation and job satisfaction

Maintenance Engineer Interview Questions Asked at Other Companies

Q1. 1)which refrigeration cycle used in chilling plant?
asked in MRF Tyres
Q2. How much bar using in hydraulic, and what is meaning of NAC.
Q3. What are the processes involved in Heat Treatment of metals and w ... read more
asked in Ceat Tyres
Q4. How many types of Valve in Instrumentation..?
Q5. What was the most difficult electrical installation or repair you ... read more

Interview questions from similar companies

Interview Questionnaire 

4 Questions

  • Q1. What is work of Pressure part in Boiler Shutdown.
  • Ans. 

    Pressure parts in boiler shutdown are inspected and maintained to ensure safe and efficient operation.

    • Pressure parts include boiler tubes, headers, and drums.

    • During shutdown, pressure parts are inspected for signs of wear, corrosion, and damage.

    • Maintenance tasks may include cleaning, repairing, or replacing pressure parts as needed.

    • Proper maintenance of pressure parts is crucial for preventing accidents and ensuring ef

  • Answered by AI
  • Q2. Tell me your self and about your previous job.
  • Q3. Asking about boiler tube material.
  • Q4. Work safely procedure.

I applied via Company Website

Interview Questionnaire 

1 Question

  • Q1. Vogele paver screed function & Temper / pressure bar applications, difference between Diesel Engine BS iv & BS VI.
  • Ans. 

    Answering questions on Vogele paver screed function and diesel engine BS iv & BS VI

    • Vogele paver screed function involves leveling and compacting asphalt or concrete surfaces

    • Temper/pressure bar applications involve adjusting the temperature and pressure of the screed to achieve desired results

    • BS IV and BS VI are emission standards for diesel engines, with BS VI being more stringent and requiring advanced technology to r...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - While sitting on interview prepare for the Basic knowledge about Machineries. Engine (Make & Model) , Hydraulic functions, Hydraulic Circuit, Power ( in Hp) etc which can build confidence to get sucess.

I applied via Campus Placement and was interviewed before Nov 2020. There were 3 interview rounds.

Interview Questionnaire 

6 Questions

  • Q1. What is gear and its types?
  • Ans. 

    Gears are mechanical components that transmit power and motion between rotating shafts. There are various types of gears.

    • Spur gears are the most common type and have straight teeth.

    • Helical gears have angled teeth and provide smoother operation.

    • Bevel gears transmit power between shafts that are not parallel.

    • Worm gears have a screw-like thread and are used for high reduction ratios.

    • Planetary gears have a central gear tha...

  • Answered by AI
  • Q2. Describe stress and strain with its diagram?
  • Ans. 

    Stress is the force applied per unit area, while strain is the deformation caused by stress.

    • Stress is measured in units of force per unit area, such as pounds per square inch (psi) or newtons per square meter (N/m²).

    • Strain is the ratio of the change in length or shape of an object to its original length or shape.

    • Stress and strain are related by the material's modulus of elasticity, which is a measure of how much the ma...

  • Answered by AI
  • Q3. How Bauxite convert into aluminium?(accordingly my internship during b.tech)
  • Q4. What is centrifugal pump and its types?
  • Ans. 

    A centrifugal pump is a mechanical device that uses centrifugal force to transport fluids. There are two types: radial and axial.

    • Centrifugal pumps are commonly used in industrial and domestic applications.

    • Radial pumps have a volute casing and are used for low flow and high head applications.

    • Axial pumps have a propeller and are used for high flow and low head applications.

    • Centrifugal pumps are easy to install and mainta...

  • Answered by AI
  • Q5. What is SI and CI engine?
  • Ans. 

    SI and CI engines are types of internal combustion engines used in vehicles and machinery.

    • SI engine stands for Spark Ignition engine, also known as gasoline engine.

    • CI engine stands for Compression Ignition engine, also known as diesel engine.

    • SI engines use a spark plug to ignite the fuel-air mixture, while CI engines use compression to ignite the fuel.

    • SI engines are commonly used in cars, motorcycles, and small machine...

  • Answered by AI
  • Q6. What is knocking?
  • Ans. 

    Knocking is a phenomenon where the air-fuel mixture in the engine cylinder ignites spontaneously before the spark plug fires.

    • Knocking is also known as detonation or pinging.

    • It can cause engine damage if not addressed.

    • It occurs when the air-fuel mixture in the cylinder ignites prematurely due to high pressure and temperature.

    • It can be caused by low-quality fuel, incorrect ignition timing, or engine overheating.

    • To preven...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - This interview was technical one and lasted for 25 minutes.The interviewer wanted to test both my knowledge and communication skill.It was my first off-campus interview and i think i did pretty well as a fresher. You need to stay calm and should apply presence of mind. you should very clear about your previous (durring b.tech) project. Ty

I applied via Referral and was interviewed before Jun 2021. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. Most questions were from prior experience. Since my expertise is into Boilers, Fired heaters, Flares, Packages etc., questions were related to my exposure to these packages. Also, I was asked if I was ok t...
Round 3 - HR 

(1 Question)

  • Q1. Only salary negotiation was done along with basic questions like reason for leaving etc.

Interview Preparation Tips

Interview preparation tips for other job seekers - Study from whatever you have worked on.
I recognised that Worley welcomes all kind of experiences pertaining to their field of operation.

I appeared for an interview in Oct 2021.

Interview Questionnaire 

3 Questions

  • Q1. Engine related
  • Q2. Gearbox related
  • Q3. Basic Principle of Working
  • Ans. 

    Basic principle of working refers to the fundamental concept or theory behind the functioning of a mechanical system.

    • It explains how a mechanical system operates and produces the desired output.

    • It is essential to understand the basic principle of working to design, develop, and maintain mechanical systems.

    • For example, the basic principle of working of an internal combustion engine is the conversion of fuel energy into ...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - what ever you learn, learn in deeply with clear concept.

Interview Questionnaire 

4 Questions

  • Q1. About Fan
  • Q2. About Aph
  • Q3. About mill
  • Q4. About esp
Interview experience
4
Good
Difficulty level
Easy
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Walk-in and was interviewed in Sep 2022. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. What is the definition of Lathe?
  • Ans. 

    A lathe is a machine tool that rotates a workpiece about an axis of rotation to perform various operations such as cutting, sanding, drilling, knurling, or deformation.

    • Lathe is used to shape and cut materials such as wood, metal, and plastic.

    • It rotates the workpiece on its axis and a cutting tool is applied to the workpiece to remove material.

    • Lathe can perform various operations such as turning, facing, drilling, borin...

  • Answered by AI
  • Q2. What is the Boiler Drum? & how it's work
  • Ans. 

    Boiler drum is a cylindrical container which is used to store water and steam produced in a boiler.

    • It is a vital component of a boiler system.

    • It is usually made of steel and is located at the top of the boiler.

    • It acts as a reservoir of water/steam and helps to separate steam from water.

    • It also helps to regulate the pressure and temperature of the steam.

    • The level of water in the drum is maintained by a feedwater control...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - For entry level, they ask simple questions.. Which means overall thermal power plant related in a layout..
Interview experience
5
Excellent
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Technical 

(2 Questions)

  • Q1. Specifiacation of machinery
  • Ans. 

    Specification of machinery refers to the detailed requirements and characteristics of a machine or equipment.

    • Includes dimensions, materials, performance criteria, and safety features

    • Should be clearly defined to ensure proper design and functionality

    • Examples: maximum load capacity, operating temperature range, power consumption

  • Answered by AI
  • Q2. Schedule maintenance interval

Interview Preparation Tips

Interview preparation tips for other job seekers - Full knowledge of schedule maintenance time interval , & root causes of machinery failure

Vaaman Engineers Interview FAQs

How many rounds are there in Vaaman Engineers Maintenance Engineer interview?
Vaaman Engineers interview process usually has 2 rounds. The most common rounds in the Vaaman Engineers interview process are Technical, Resume Shortlist and HR.
What are the top questions asked in Vaaman Engineers Maintenance Engineer interview?

Some of the top questions asked at the Vaaman Engineers Maintenance Engineer interview -

  1. Conveyor belt changing proced...read more
  2. Gear box changing proc...read more

Tell us how to improve this page.

Vaaman Engineers Maintenance Engineer Interview Process

based on 3 interviews

Interview experience

4
  
Good
View more

Interview Questions from Similar Companies

Tata Technologies Interview Questions
3.6
 • 263 Interviews
TCE Interview Questions
3.8
 • 251 Interviews
Saint-Gobain Interview Questions
4.0
 • 173 Interviews
Dilip Buildcon Interview Questions
4.0
 • 146 Interviews
G R Infraprojects Interview Questions
4.1
 • 134 Interviews
Worley Interview Questions
4.1
 • 113 Interviews
View all
Vaaman Engineers Maintenance Engineer Salary
based on 26 salaries
₹2.1 L/yr - ₹7 L/yr
6% more than the average Maintenance Engineer Salary in India
View more details

Vaaman Engineers Maintenance Engineer Reviews and Ratings

based on 10 reviews

4.7/5

Rating in categories

4.7

Skill development

4.4

Work-life balance

4.2

Salary

4.5

Job security

4.5

Company culture

4.1

Promotions

4.5

Work satisfaction

Explore 10 Reviews and Ratings
Mechanical Engineer
124 salaries
unlock blur

₹1.6 L/yr - ₹5.6 L/yr

Shift Incharge
77 salaries
unlock blur

₹2.5 L/yr - ₹6.5 L/yr

Safety Officer
56 salaries
unlock blur

₹2.2 L/yr - ₹5.3 L/yr

Mechanical Maintenance Engineer
51 salaries
unlock blur

₹2.3 L/yr - ₹7.2 L/yr

Shift Engineer
44 salaries
unlock blur

₹2.5 L/yr - ₹5 L/yr

Explore more salaries
Compare Vaaman Engineers with

Megha Engineering & Infrastructures

3.9
Compare

Shapoorji Pallonji Group

4.1
Compare

Alstom Transportation

3.7
Compare

Tata Technologies

3.6
Compare
Did you find this page helpful?
Yes No
write
Share an Interview