Filter interviews by
I applied via Referral
Doubly reinforced beam has reinforcement in both tension and compression zones, while singly reinforced beam has reinforcement only in tension zone.
Doubly reinforced beam can withstand higher loads and bending moments.
Singly reinforced beam is simpler and cheaper to construct.
Doubly reinforced beam is used in structures with heavy loads or long spans.
Singly reinforced beam is used in structures with lighter loads or sh...
Shape factor is a measure of the efficiency of a beam's cross-sectional shape in resisting bending. Different types of beams in steel structures include I-beams, H-beams, and C-beams.
Shape factor is calculated by dividing the moment of inertia of the beam's cross-section by the product of the beam's width and the cube of its depth.
I-beams are commonly used in construction due to their high strength-to-weight ratio.
H-be...
Slope and deflections of cantilever and simply supported beams under standard loading system.
Cantilever beams have fixed support at one end and free at the other.
Simply supported beams have support at both ends.
Standard loading system includes point load, uniformly distributed load, and triangular load.
Slope is the angle of deflection at a point on the beam.
Deflection is the displacement of a point on the beam from its
Point of contraflexure is where bending moment changes sign in a beam.
It is the point where bending moment is zero.
It occurs in simply supported beams at the center.
In cantilever beams, it occurs at the fixed end.
In overhanging beams, it occurs at the free end of the overhang.
It is important to consider in beam design to prevent failure.
The maximum and minimum percentage of steel in columns depends on various factors such as the type of column, its height, and the load it needs to bear.
The percentage of steel in columns can range from 0.5% to 6% depending on the type of column.
For short columns, the percentage of steel can be as low as 0.5% while for tall columns, it can go up to 6%.
The load that the column needs to bear also plays a crucial role in d...
Doubly reinforced beams are used when the depth of the beam is limited and the load-bearing capacity needs to be increased.
Doubly reinforced beams are used in construction where the depth of the beam is limited and the load-bearing capacity needs to be increased
They are commonly used in bridges, high-rise buildings, and parking garages
Doubly reinforced beams have steel reinforcement bars in both the compression and ten...
The minimum percentage of steel in a slab depends on various factors such as load, span, and thickness.
The minimum percentage of steel in a slab is generally 0.15% to 0.2% of the cross-sectional area.
The percentage of steel may vary depending on the type of slab, such as one-way or two-way slab.
The thickness of the slab also plays a crucial role in determining the minimum percentage of steel.
The load and span of the sl...
Top trending discussions
posted on 14 May 2022
I applied via Naukri.com and was interviewed before May 2021. There was 1 interview round.
I applied via Walk-in and was interviewed before Apr 2020. There were 5 interview rounds.
I was interviewed before Sep 2020.
Round duration - 140 minutes
Round difficulty - Medium
Test timing was at 2:00 pm , it was conducted in a college and the environment was good for the test. Camera was a primary part of test, so no suspicious activity.
Given two numbers in the form of two arrays where each element of the array represents a digit, calculate the sum of these two numbers and return this sum as an ar...
Given two numbers represented as arrays, calculate their sum and return the result as an array.
Iterate through the arrays from right to left, adding digits and carrying over if necessary
Handle cases where one array is longer than the other by considering the remaining digits
Ensure the final sum array does not have any leading zeros
Round duration - 20 minutes
Round difficulty - Easy
The round was conducted at around 12 p.m. I was called at the college location and then it was conducted. The interviewer was quite polite and frank.
Round duration - 8 minutes
Round difficulty - Easy
This round was conducted right after finishing and clearing the technical round at the same place and on the same day.
Tip 1 : Practice atleast 2-3 Coding problems daily so your logic building becomes stronger.
Tip 2 : Exercise problems based on OOPS concepts and others too.
Tip 3 : If you can have your own project built, then it's the major point and will act as a plus point.
Tip 1 : Your resume should be in standard form, short and simple will be more effective.
Tip 2 : Whatever you have learned, you need to mention it in your resume as that will be your primary source of selection and having project on your resume is important.
I applied via Recruitment Consultant and was interviewed before Sep 2020. There were 3 interview rounds.
I applied via Naukri.com and was interviewed in Jul 2020. There were 4 interview rounds.
I applied via Job Portal and was interviewed before Apr 2021. There was 1 interview round.
Solid principles are a set of design principles for writing maintainable and scalable code in C#.
Single Responsibility Principle (SRP) - a class should have only one reason to change
Open/Closed Principle (OCP) - a class should be open for extension but closed for modification
Liskov Substitution Principle (LSP) - derived classes should be substitutable for their base classes
Interface Segregation Principle (ISP) - client...
I applied via Campus Placement and was interviewed before May 2020. There were 4 interview rounds.
I applied via Naukri.com and was interviewed before Apr 2020. There were 5 interview rounds.
Some of the top questions asked at the UBC Impex interview -
based on 1 interview
Interview experience
TCS
Accenture
Wipro
Cognizant