i
Tata Power
Proud winner of ABECA 2024 - AmbitionBox Employee Choice Awards
Filter interviews by
Top trending discussions
I applied via Referral and was interviewed in Mar 2024. There were 2 interview rounds.
Possible reasons for cube failure despite good materials
Improper mixing of materials
Incorrect curing process
Inadequate compaction of concrete
Presence of air voids or impurities
Poor quality control during manufacturing
Compression test is conducted after cube test to determine the compressive strength of concrete.
Compression test is conducted to determine the compressive strength of concrete.
It involves applying a gradually increasing load to the concrete specimen until failure.
The results of the compression test help in assessing the quality of the concrete mix and its ability to withstand compressive forces.
Compression test is an i...
The quantity of cement used in M35 grade concrete varies depending on the mix design and specifications.
The quantity of cement in M35 grade concrete typically ranges from 360 to 420 kg/m3.
The exact amount of cement needed can be calculated using the mix design provided for the project.
Factors such as water-cement ratio, aggregate size, and admixtures also influence the quantity of cement required.
I applied via Approached by Company and was interviewed in Feb 2023. There were 3 interview rounds.
Any one question in my sinner??
I applied via Naukri.com and was interviewed in Nov 2023. There was 1 interview round.
A 1 gigawatt required pallet is a pallet that can handle the weight and power requirements of a 1 gigawatt load.
A 1 gigawatt required pallet needs to be able to support the weight of a 1 gigawatt load.
It should have a strong and sturdy construction to prevent any damage or collapse.
The pallet should be designed to handle the power requirements of a 1 gigawatt load, ensuring proper electrical connections and insulation.
...
Blocking diodes are used in junction boxes to prevent reverse current flow and protect electrical components.
Blocking diodes are used to prevent reverse current flow in electrical circuits.
They protect electrical components from damage caused by reverse voltage.
Blocking diodes are commonly used in junction boxes to ensure proper current flow.
They are also used in solar panels to prevent power loss due to reverse curren...
If module temperature increases, it can lead to reduced efficiency, increased stress on components, and potential failure.
Increased temperature can cause a decrease in the efficiency of the module.
Higher temperatures can lead to increased stress on components, potentially reducing their lifespan.
Excessive heat can cause thermal expansion and contraction, which may result in mechanical failure.
Increased temperature can ...
My life goal is to make a positive impact on society by ensuring quality in engineering processes.
To continuously improve and optimize engineering processes
To ensure products meet high quality standards
To contribute to the development of innovative and reliable solutions
To collaborate with cross-functional teams to drive quality improvements
To mentor and inspire others in the field of quality engineering
I applied via Walk-in and was interviewed in Feb 2024. There was 1 interview round.
I applied via Company Website and was interviewed in Apr 2023. There were 3 interview rounds.
A sinusoidal wave is a type of wave that has a smooth, repetitive oscillation resembling a sine curve.
Sinusoidal waves are characterized by their amplitude, frequency, and phase.
They are commonly seen in AC electrical circuits, sound waves, and light waves.
The equation for a sinusoidal wave is typically represented as y = A*sin(2*pi*f*t + phi), where A is the amplitude, f is the frequency, t is time, and phi is the pha...
Peak factor is the ratio of peak value to the RMS value of a waveform.
Peak factor is used to quantify the peakiness of a waveform.
It is calculated by dividing the peak value of the waveform by its RMS value.
A higher peak factor indicates a more peaky waveform with larger peaks relative to the average value.
Peak factor is important in signal processing and power systems analysis.
The stator and rotor are key components of an electric motor. The stator is the stationary part that generates a magnetic field, while the rotor is the rotating part that interacts with the magnetic field to produce motion.
Stator is the stationary part of an electric motor
Stator generates a magnetic field
Rotor is the rotating part of an electric motor
Rotor interacts with the magnetic field generated by the stator to pr
I applied via Naukri.com and was interviewed in Nov 2020. There were 3 interview rounds.
To analyse total diesel consumption in equipment, I would gather data on usage and calculate fuel efficiency.
Collect data on equipment usage and fuel consumption
Calculate fuel efficiency by dividing fuel consumption by equipment usage
Compare fuel efficiency across different equipment to identify outliers
Identify factors that may affect fuel efficiency, such as maintenance or operator behavior
Excel , data specialist
I moved from a government company to gain more diverse experience and opportunities for growth.
Seeking new challenges and opportunities for career advancement
Desire for a more dynamic work environment
Wanted to work on a wider range of projects
Government company may have limitations in terms of innovation and flexibility
based on 3 interviews
Interview experience
based on 10 reviews
Rating in categories
Lead Engineer
745
salaries
| ₹0 L/yr - ₹0 L/yr |
Team Lead
222
salaries
| ₹0 L/yr - ₹0 L/yr |
Assistant Manager
182
salaries
| ₹0 L/yr - ₹0 L/yr |
Manager
179
salaries
| ₹0 L/yr - ₹0 L/yr |
Graduate Engineer Trainee (Get)
130
salaries
| ₹0 L/yr - ₹0 L/yr |
Adani Power
NTPC
Reliance Power
JSW Energy