Filter interviews by
I applied via Walk-in and was interviewed in Oct 2021. There was 1 interview round.
Types of lubrication include hydrodynamic, boundary, and mixed lubrication.
Hydrodynamic lubrication occurs when a fluid film separates the moving surfaces, such as in engines.
Boundary lubrication involves a thin layer of lubricant that prevents direct contact between surfaces, like in metal cutting.
Mixed lubrication combines elements of both hydrodynamic and boundary lubrication, commonly found in many mechanical syste
Lubrication grades of grease and gear oil
Grease lubrication grades are NLGI 000, 00, 0, 1, 2, 3
Gear oil lubrication grades are classified by the American Petroleum Institute (API) as GL-1, GL-2, GL-3, GL-4, GL-5, and GL-6
The higher the number, the more viscous the lubricant
The support roller bearing number depends on the specific application and load requirements.
The bearing number should be selected based on the load capacity and speed requirements of the support roller.
Factors such as temperature, lubrication, and alignment should also be considered when selecting a bearing.
Examples of support roller bearings include cylindrical roller bearings, spherical roller bearings, and needle ro
The support roller bore diameter is the size of the hole in the center of the support roller.
The bore diameter is important for selecting the appropriate bearing size.
It is also important for ensuring proper alignment and fit with the shaft.
The bore diameter can vary depending on the size and type of support roller.
For example, a small support roller may have a bore diameter of 1 inch, while a larger one may have a bor
Types of vibration include free, forced, damped, and self-excited.
Free vibration occurs when a system oscillates on its own without any external force.
Forced vibration occurs when a system is subjected to an external force.
Damped vibration is when the amplitude of vibration decreases over time due to energy dissipation.
Self-excited vibration occurs when a system vibrates due to its own internal forces, such as in a gui
Viscosity is the measure of a fluid's resistance to flow.
Viscosity is affected by temperature and pressure.
It is measured in units of poise or centipoise.
High viscosity fluids are thick and flow slowly, while low viscosity fluids are thin and flow quickly.
Examples of high viscosity fluids include honey and molasses, while water and alcohol are low viscosity fluids.
Viscosity is measured in units of poise or centipoise.
Viscosity is a measure of a fluid's resistance to flow.
The unit of viscosity is poise or centipoise.
Water has a viscosity of 1 centipoise at room temperature.
Honey has a viscosity of around 2000 centipoise.
Viscosity can be affected by temperature and pressure.
Density unit is the measure of mass per unit volume of a substance.
Density unit is expressed in kg/m³ or g/cm³.
It is used to compare the mass of different substances with the same volume.
Commonly used in industries like construction, oil and gas, and pharmaceuticals.
Example: The density of water is 1000 kg/m³ or 1 g/cm³.
Various types of breakdown can occur in a crusher.
Mechanical breakdown due to wear and tear of components
Electrical breakdown due to faulty wiring or components
Hydraulic breakdown due to leaks or malfunctioning of hydraulic system
Material breakdown due to foreign objects or excessive feed size
Operational breakdown due to improper use or maintenance
Examples include bearing failure, motor burnout, hydraulic cylinder fail
The gear ratio of the main drive oil gearbox is typically specified by the manufacturer.
The gear ratio determines the speed and torque of the output shaft relative to the input shaft.
It is important to select the appropriate gear ratio for the application to ensure optimal performance.
The gear ratio can be calculated by dividing the number of teeth on the output gear by the number of teeth on the input gear.
For example...
A pneumatic cylinder is a mechanical device that uses compressed air to produce force in a reciprocating linear motion.
Pneumatic cylinders are commonly used in industrial automation and robotics.
They are often used to move and position objects, as well as to apply force.
Pneumatic cylinders come in various sizes and shapes, including single-acting and double-acting cylinders.
They can be made from materials such as alumi...
Impactor capacity refers to the maximum amount of material that can be processed by an impactor machine.
Impactor capacity is typically measured in tons per hour.
It is important to match the impactor capacity to the desired output of the operation.
Factors that can affect impactor capacity include the size and type of material being processed, the speed of the machine, and the size of the feed opening.
For example, a hori...
EP2 and OG1 are two different types of grease grades with different properties.
EP2 is a high-performance grease with extreme pressure additives that provide excellent protection against wear and tear.
OG1 is a general-purpose grease that is suitable for a wide range of applications.
EP2 is typically used in heavy-duty applications such as mining equipment, construction machinery, and industrial gearboxes.
OG1 is commonly ...
The grade used in girth gear, bearing, and seal depends on the specific application and load requirements.
The grade of girth gear depends on the size and load capacity of the gear.
The grade of bearing depends on the speed and load capacity of the application.
The grade of seal depends on the type of fluid being sealed and the operating temperature and pressure.
Common grades for girth gears include ASTM A105, ASTM A350 L...
Screw compressors use screws to compress air while lobe compressors use lobes or rotors.
Screw compressors have two interlocking screws that rotate in opposite directions to compress air.
Lobe compressors have two or three lobes or rotors that rotate in opposite directions to compress air.
Screw compressors are more efficient and have a higher compression ratio than lobe compressors.
Lobe compressors are more suitable for ...
The type of bearing used in RALF and pump is usually a ball bearing or roller bearing.
Ball bearings are commonly used in RALF and pump applications due to their ability to handle radial and axial loads.
Roller bearings are also used in some applications where higher load capacity is required.
The specific type of bearing used will depend on the size and speed of the equipment.
Proper lubrication is important for the longe...
A basic aptitude test and assessment of reasoning abilities.
The laws of thermodynamics are fundamental principles that govern energy and its transformations in a system.
The first law of thermodynamics states that energy cannot be created or destroyed, only transferred or converted.
The second law of thermodynamics states that the total entropy of an isolated system can never decrease over time.
The third law of thermodynamics states that as a system approaches absolute zero, the ...
Shyam Sel & Power interview questions for popular designations
Get interview-ready with Top Shyam Sel & Power Interview Questions
I was interviewed in Dec 2024.
Logical reasoning
Numerical ability
Situational based Mcqs
Domain specific Technical Mcqs
Prepare well for this one.
Topic : Recent Trending Topics
I was interviewed in Dec 2024.
I am looking for growth opportunities, a challenging work environment, and the chance to develop my skills.
Seeking opportunities for career advancement
Interested in a challenging work environment
Looking to develop and enhance my skills
Open to learning new things and taking on new responsibilities
I applied via Referral and was interviewed in Apr 2024. There was 1 interview round.
The least count of a micrometer is the smallest measurement that can be read on the scale of the micrometer.
The least count of a micrometer is typically 0.01 mm or 0.001 mm, depending on the type of micrometer.
It is important to understand the least count in order to accurately measure dimensions using a micrometer.
For example, a micrometer with a least count of 0.01 mm can measure up to two decimal places, while a mic...
The standard mill speed varies depending on the diameter of the mill.
The standard mill speed for a specific diameter can be calculated using the formula: Speed = (Diameter x π x RPM) / 1000
Different mills may have different standard speeds based on their size and purpose
It is important to refer to the manufacturer's guidelines for the recommended mill speed for each diameter
Top trending discussions
The duration of Shyam Sel & Power interview process can vary, but typically it takes about less than 2 weeks to complete.
based on 59 interviews
Interview experience
based on 308 reviews
Rating in categories
Engineer
55
salaries
| ₹0 L/yr - ₹0 L/yr |
Assistant Engineer
51
salaries
| ₹0 L/yr - ₹0 L/yr |
Assistant Manager
50
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Engineer
50
salaries
| ₹0 L/yr - ₹0 L/yr |
Electrical Engineer
29
salaries
| ₹0 L/yr - ₹0 L/yr |
Tata Power
Adani Power
NTPC
Reliance Power