i
Royal Enfield
Proud winner of ABECA 2024 - AmbitionBox Employee Choice Awards
Filter interviews by
I applied via Naukri.com and was interviewed in Sep 2023. There was 1 interview round.
The number of sensors in a bike varies depending on the make and model, but typically includes sensors for speed, temperature, and fuel levels.
Number of sensors in a bike can range from 5 to 30 depending on the complexity of the bike.
Common sensors in a bike include speed sensors, temperature sensors, fuel level sensors, and tire pressure sensors.
Some high-end bikes may also have sensors for lean angle, suspension trav...
TPS sensor stands for Throttle Position Sensor, which monitors the position of the throttle valve.
TPS sensor is a crucial component in the engine management system.
It helps in determining the amount of air entering the engine.
The sensor sends this information to the engine control unit (ECU) to adjust fuel injection and ignition timing.
A faulty TPS sensor can cause issues like poor acceleration, stalling, or rough idli...
The HT coil, also known as the high tension coil, is an essential component in the ignition system of a vehicle, responsible for generating high voltage to create a spark in the spark plugs.
HT coil is a type of ignition coil used in vehicles to produce high voltage for the spark plugs
It is typically located near the engine and connected to the distributor or ignition module
A faulty HT coil can result in misfiring, roug
An h2 sensor is a hydrogen sensor used to detect the presence of hydrogen gas in a given environment.
H2 sensors are commonly used in industrial settings to monitor for leaks in hydrogen gas pipelines.
They are also used in fuel cell vehicles to ensure safe operation.
The sensor typically works by detecting changes in electrical conductivity when exposed to hydrogen gas.
CDI (Capacitor Discharge Ignition) and RR (Rectifier Regulator) units work together to regulate the electrical system in a motorcycle.
CDI unit stores energy from the stator and releases it to the ignition coil to create a spark for combustion.
RR unit regulates the voltage produced by the stator to prevent overcharging of the battery.
CDI and RR units work in tandem to ensure proper ignition timing and electrical system ...
Top trending discussions
I was interviewed before Jul 2023.
Ohm's law states that the current flowing through a conductor is directly proportional to the voltage across it, and inversely proportional to the resistance of the conductor.
Ohm's law is represented by the formula V = IR, where V is voltage, I is current, and R is resistance.
It is named after the German physicist Georg Simon Ohm.
The law is commonly used in electrical engineering to calculate the relationship between v...
BMW is a German luxury automobile manufacturer known for its high-performance vehicles and innovative technology.
BMW stands for Bayerische Motoren Werke AG
Founded in 1916, BMW is headquartered in Munich, Germany
BMW is known for its luxury vehicles, motorcycles, and engines
The BMW logo represents a rotating airplane propeller, paying homage to the company's aviation history
BMW's M division produces high-performance vers...
I applied via Naukri.com and was interviewed in Oct 2022. There were 3 interview rounds.
Maths(percentage, profit and loss)
Reasoning (average coding deciding blood relation)
I applied via Naukri.com and was interviewed before Apr 2020. There was 1 interview round.
Yes, mechanic work can be physically demanding and requires strength and endurance.
Mechanics often have to lift heavy parts and equipment
They may have to work in uncomfortable positions or tight spaces
Repetitive motions can lead to strain and fatigue
Working with tools and machinery can be dangerous if not done properly
I applied via Indeed and was interviewed in Dec 2024. There were 3 interview rounds.
Good and better , nice
posted on 1 Nov 2024
I applied via Referral and was interviewed in Oct 2024. There were 3 interview rounds.
Bending moment calculation involves determining the internal bending forces in a structure.
Bending moment is the algebraic sum of moments about the neutral axis of a cross section of a beam or other structural element.
It is calculated using the formula: M = F * d, where M is the bending moment, F is the force applied, and d is the perpendicular distance from the force to the neutral axis.
Bending moment diagrams are use...
posted on 8 Sep 2024
I applied via Recruitment Consulltant and was interviewed in Aug 2024. There was 1 interview round.
Diesel has higher energy density than petrol, resulting in better fuel efficiency.
Diesel has a higher energy density than petrol, meaning it can provide more energy per unit volume.
Petrol is more volatile and burns faster than diesel.
The capacity of diesel and petrol tanks in vehicles can vary depending on the size of the vehicle and its fuel efficiency.
For example, a typical car may have a petrol tank capacity of arou...
Petrol engines use spark ignition, while diesel engines use compression ignition.
Petrol engines use a spark plug to ignite the fuel-air mixture, while diesel engines rely on compression to ignite the fuel.
Petrol engines are lighter and more responsive, while diesel engines are more fuel-efficient and have higher torque.
Petrol engines are more common in cars and motorcycles, while diesel engines are often used in trucks
LNTD stands for Logarithmic Mean Temperature Difference.
LNTD is a term used in heat transfer calculations to determine the overall temperature difference between two fluids in a heat exchanger.
It is calculated using the formula LNTD = (ΔT1 - ΔT2) / ln(ΔT1 / ΔT2), where ΔT1 and ΔT2 are the temperature differences at the two ends of the heat exchanger.
LNTD is important in designing efficient heat exchangers to maximize h...
posted on 11 Sep 2024
On-Board Diagnostics
On-Board Diagnostics (OBD) is a system in vehicles that monitors the performance of the engine and emissions systems.
It helps to identify issues and malfunctions by providing codes that can be read with a diagnostic tool.
OBD systems have evolved over the years, with OBD-II being the current standard in most vehicles.
Examples of OBD codes include P0300 for random misfire and P0420 for catalytic conve
posted on 6 Oct 2023
I applied via Company Website and was interviewed in Jul 2023. There were 3 interview rounds.
Yes i want aptitude test plz share on me email
1 more round
Hard working
Embition
Cansantrated
Internal combustion engines are classified into two main types: spark ignition (SI) engines and compression ignition (CI) engines.
Spark ignition (SI) engines use a spark plug to ignite the fuel-air mixture, commonly found in gasoline engines.
Compression ignition (CI) engines rely on the heat generated by compressing the air in the cylinder to ignite the fuel, commonly found in diesel engines.
Each type of engine has its...
Instruments are used in various ways in mechanical engineering, such as for measuring, testing, and analyzing different parameters.
Instruments are used for measuring various parameters like temperature, pressure, flow rate, etc.
Instruments are used for testing the performance of mechanical systems and components.
Instruments are used for analyzing data and making informed decisions based on the results.
Examples include ...
Quality control is essential in ensuring products meet standards and specifications.
Quality control involves monitoring and testing products to ensure they meet specified standards.
It helps identify defects or issues early in the production process.
Quality control can involve inspections, testing, and audits to ensure consistency and reliability.
Examples include checking dimensions of a part, testing the strength of a
based on 1 interview
Interview experience
based on 4 reviews
Rating in categories
Assistant Manager
968
salaries
| ₹5 L/yr - ₹16 L/yr |
Deputy Manager
494
salaries
| ₹8.9 L/yr - ₹23 L/yr |
Store Executive
350
salaries
| ₹1.4 L/yr - ₹3.6 L/yr |
Trainee
333
salaries
| ₹1.5 L/yr - ₹3.5 L/yr |
Senior Engineer
296
salaries
| ₹4.2 L/yr - ₹10.1 L/yr |
Bajaj Auto
Hero MotoCorp
TVS Motor
Yamaha Motor