i
Quest Global
Filter interviews by
I applied via Naukri.com and was interviewed in Nov 2021. There were 3 interview rounds.
Non-linearity convergence issue can be resolved by adjusting the solver settings and/or modifying the model.
Check the initial conditions and boundary conditions
Try using a different solver or adjusting the solver settings
Modify the model to reduce non-linearity
Check for any errors in the input data or model setup
Increase the number of iterations or decrease the convergence tolerance
Consider using sub-stepping or adapti...
Ansys APDL has various types of elements including structural, thermal, fluid, electromagnetic, and acoustic elements.
Structural elements include beam, shell, and solid elements
Thermal elements include conduction, convection, and radiation elements
Fluid elements include 1D, 2D, and 3D elements for incompressible and compressible flows
Electromagnetic elements include magnetic, electric, and coupled field elements
Acousti...
Solid elements have 3 degrees of freedom (DOF) because they can only deform in 3 directions.
Solid elements are used to model objects that are not easily deformed in all directions
The 3 DOF are translations in x, y, and z directions
Examples include beams, columns, and plates
The number of zero natural frequencies in free-free modal analysis of hex elements.
Free-free modal analysis
Hex elements
Zero natural frequencies
Materials properties required for thermal analysis
Thermal conductivity
Specific heat capacity
Thermal expansion coefficient
Melting point
Boiling point
Heat transfer coefficient
Thermal diffusivity
Quality checks for mesh include element size, aspect ratio, skewness, orthogonality, and boundary conformity.
Element size should be appropriate for the geometry and physics of the problem.
Aspect ratio should be within acceptable limits to avoid distorted elements.
Skewness should be minimized to avoid numerical errors.
Orthogonality should be maintained to ensure accurate results.
Boundary conformity should be checked to ...
I applied via Referral and was interviewed before Jul 2021. There were 3 interview rounds.
I applied via Approached by Company and was interviewed before Apr 2021. There were 3 interview rounds.
Low cycle fatigue occurs at high stress levels and a small number of cycles, while high cycle fatigue occurs at low stress levels and a large number of cycles.
Low cycle fatigue is caused by plastic deformation and occurs at stress levels above the yield strength of the material.
High cycle fatigue is caused by cyclic loading and occurs at stress levels below the yield strength of the material.
Low cycle fatigue is typica...
Quest Global interview questions for designations
I applied via Approached by Company and was interviewed before Apr 2021. There were 2 interview rounds.
Principal stress is the maximum or minimum normal stress acting on a plane at a point in a stressed body.
Principal stress is a type of normal stress.
It occurs on a plane where the shear stress is zero.
The maximum and minimum principal stresses are perpendicular to each other.
The principal stresses are important in determining the failure of a material.
Examples of applications include designing structures and analyzing
Get interview-ready with Top Quest Global Interview Questions
I applied via Recruitment Consultant and was interviewed before Jan 2021. There were 4 interview rounds.
Normal, class 10 apti plus english
3 question on string manipulation
Some of the top questions asked at the Quest Global FEA Engineer interview -
based on 1 interview
2 Interview rounds
based on 13 reviews
Rating in categories
Senior Software Engineer
2.4k
salaries
| ₹4.8 L/yr - ₹20 L/yr |
Senior Engineer
1.8k
salaries
| ₹4.9 L/yr - ₹18 L/yr |
Software Engineer
1.7k
salaries
| ₹2.8 L/yr - ₹9.6 L/yr |
Lead Engineer
1.7k
salaries
| ₹7.6 L/yr - ₹24 L/yr |
Design Engineer
643
salaries
| ₹2 L/yr - ₹8.3 L/yr |
Virtusa Consulting Services
Genpact
Nagarro
Sopra Steria