Filter interviews by
I appeared for an interview in Jan 2025.
I applied via Approached by Company and was interviewed in Oct 2024. There was 1 interview round.
Tool test in respected discipline involves evaluating the proficiency of a candidate in using relevant software tools.
Demonstrate proficiency in using BIM software such as Revit, Navisworks, or AutoCAD.
Show ability to create 3D models, clash detection, and generate construction drawings.
Experience in using BIM collaboration tools like BIM 360 for project coordination.
Knowledge of industry standards and best practices i...
Petrocon Engineers & Consultants interview questions for popular designations
Steam traps are used to remove condensate and non-condensable gases from steam systems to prevent damage and improve efficiency.
Steam traps prevent condensate from accumulating in steam systems, which can cause damage and reduce efficiency.
They also remove non-condensable gases, such as air, from the system to ensure proper heat transfer.
There are different types of steam traps, including mechanical, thermostatic, and ...
The Sp3d designing tool test evaluates a candidate's proficiency in using the Sp3d software for 3D design.
Demonstrate knowledge of Sp3d interface and tools
Show ability to create 3D models and structures accurately
Explain how to generate reports and drawings using Sp3d
Discuss experience with clash detection and resolution in Sp3d
I applied via Walk-in and was interviewed before Aug 2022. There were 2 interview rounds.
Base shear can be calculated using the seismic coefficient method or the equivalent lateral force method.
Base shear can be calculated using the formula: V = Cs * W, where Cs is the seismic coefficient and W is the total weight of the structure.
Seismic coefficient can be determined based on the seismic zone and the type of structure.
Equivalent lateral force method involves calculating the total lateral force acting on t...
The CF value for a pipe rack is typically determined based on the specific design requirements and load conditions.
CF value stands for Capacity Factor, which is used to determine the load capacity of a pipe rack structure.
The CF value can vary depending on factors such as material type, design codes, and safety factors.
Calculating the CF value involves considering the maximum load the pipe rack will need to support and...
The question is asking about the load factor for pipe rack and pipes.
cf is 2 for pipe rack and 0.7 for pipes
cf stands for load factor
The load factor for pipe rack is higher than for pipes
I applied via Approached by Company and was interviewed before Apr 2023. There was 1 interview round.
Top trending discussions
I appeared for an interview before Mar 2024, where I was asked the following questions.
I have extensive experience in structural engineering, focusing on design, analysis, and project management across various sectors.
Worked on the design of a 20-story commercial building, ensuring compliance with local codes and safety standards.
Conducted structural analysis using software like SAP2000 and ETABS for various projects, improving efficiency by 30%.
Collaborated with architects and contractors to optimize de...
posted on 18 Dec 2021
I appeared for an interview in Jun 2021.
The loads considered in telecom towers design include wind loads, dead loads, ice loads, and equipment loads.
Wind loads: Towers are designed to withstand the force of wind at different speeds and directions.
Dead loads: These include the weight of the tower structure itself and any permanent fixtures.
Ice loads: Towers in cold climates need to be designed to support the weight of ice accumulation.
Equipment loads: The wei...
Wind load calculation as per IS875 involves determining the wind pressure acting on the structure and calculating the resultant force.
Wind pressure is calculated based on the wind speed and the terrain category of the site
The pressure coefficients for different parts of the structure are determined based on the shape and orientation of the surface
The wind load acting on the structure is calculated by multiplying the pr...
based on 11 interviews
Interview experience
based on 160 reviews
Rating in categories
Piping Designer
126
salaries
| ₹1.8 L/yr - ₹7.5 L/yr |
Piping Design Engineer
89
salaries
| ₹1.3 L/yr - ₹6 L/yr |
Design Engineer
22
salaries
| ₹1.2 L/yr - ₹7.2 L/yr |
Process Engineer
18
salaries
| ₹2.4 L/yr - ₹9 L/yr |
Electrical Designer
18
salaries
| ₹2.5 L/yr - ₹6.5 L/yr |
Lea Associates South Asia
McNally Bharat Engineering
R.V.R. PROJECTS
ABCI Infrastructures