Filter interviews by
I applied via Approached by Company and was interviewed in Jun 2024. There were 2 interview rounds.
Top trending discussions
posted on 24 Dec 2024
I applied via Newspaper Ad
posted on 1 Aug 2021
posted on 17 Feb 2024
I applied via Campus Placement and was interviewed before May 2022. There were 2 interview rounds.
The number of parts in sfc panels varies depending on the specific panel and its design.
The number of parts can range from a few to several hundred.
Some common parts include solar cells, wiring, and protective coatings.
The number of parts can also depend on the size and power output of the panel.
Manufacturers may use different materials and designs, affecting the number of parts.
It is important to consider the number a...
Slip-ring motor speed can be controlled by varying the resistance in the rotor circuit.
Slip-ring motors have a wound rotor with external resistors.
By changing the resistance in the rotor circuit, the speed can be controlled.
This is done by adding or removing resistors from the rotor circuit.
The speed can also be controlled by changing the voltage applied to the stator.
This method is commonly used in industries where va...
Adding external resistance increases the total resistance in a circuit.
External resistance can be added in series or parallel to the existing circuit.
This can be useful in controlling the current flow and voltage drop in the circuit.
For example, adding a resistor in series with an LED can limit the current flowing through it and prevent it from burning out.
Similarly, adding a resistor in parallel with a component can r...
Main parts of eot cranes include bridge, trolley, hoist, end trucks, runway beams, and electrical components.
Bridge: main structure that spans the width of the bay
Trolley: carries the hoist and moves horizontally along the bridge
Hoist: lifts and lowers the load
End trucks: located on either side of the bridge and house the wheels for movement
Runway beams: support the crane and provide a path for the crane to travel alon...
Slip-ring motors are used in EOT cranes for their ability to provide high starting torque and smooth acceleration.
Slip-ring motors offer high starting torque, making them suitable for heavy loads in EOT cranes.
They provide smooth acceleration, reducing wear and tear on the crane components.
Slip-ring motors allow for speed control and reversing capabilities, important in crane operations.
These motors are also able to ha...
I applied via Approached by Company and was interviewed in Oct 2023. There was 1 interview round.
A starter control circuit is used to control the starting and stopping of an electric motor.
The starter control circuit typically includes a start button, stop button, overload relay, and contactor.
When the start button is pressed, it energizes the contactor which allows power to flow to the motor.
The overload relay protects the motor from overheating by sensing the current drawn by the motor.
The stop button breaks the...
To perform an id run test on a VFD, you need to follow specific steps to ensure the variable frequency drive is functioning correctly.
Connect the VFD to a motor and power supply
Set the VFD parameters according to the motor specifications
Run the motor at different speeds to test the VFD's ability to control the motor
Monitor the motor's performance and check for any abnormalities
Record the test results for analysis and t
I applied via Recruitment Consulltant
Logistic Analysis & previous projects
I applied via Company Website and was interviewed before Jun 2023. There were 3 interview rounds.
Quality Checking process
I applied via Walk-in and was interviewed in Dec 2023. There was 1 interview round.
I applied via Naukri.com and was interviewed before Apr 2023. There was 1 interview round.
The 7 QC Tools are a set of basic tools used for quality control and problem-solving in manufacturing and other industries.
Check sheet: Used to collect and analyze data in a systematic manner.
Histogram: A visual representation of data distribution.
Pareto chart: Helps identify the most significant factors contributing to a problem.
Cause-and-effect diagram (Fishbone diagram): Used to identify and analyze potential causes...
Handle customer complaints by listening, empathizing, investigating, resolving, and following up.
Listen to the customer's complaint without interrupting
Empathize with the customer's situation and show understanding
Investigate the root cause of the complaint to prevent future occurrences
Resolve the issue promptly and effectively
Follow up with the customer to ensure satisfaction and prevent recurrence
GD&T stands for Geometric Dimensioning and Tolerancing, a system for defining and communicating engineering tolerances.
GD&T is a symbolic language used on engineering drawings to specify the allowable variations in form, size, and orientation of features.
It helps ensure that parts fit together properly and function as intended.
GD&T includes symbols, such as concentricity, flatness, perpendicularity, and position, to co...
The 5 core tools of Quality are essential techniques used in quality management to ensure products and processes meet standards.
1. Process Flowcharts: Used to visually represent the steps in a process.
2. Cause and Effect Diagrams (Fishbone Diagrams): Used to identify and analyze potential causes of a problem.
3. Control Charts: Used to monitor process variation over time.
4. Check Sheets: Used to collect and analyze data...
based on 1 interview
Interview experience
Senior Executive
185
salaries
| ₹3.2 L/yr - ₹7.2 L/yr |
Executive
166
salaries
| ₹2 L/yr - ₹6 L/yr |
Assistant Manager
151
salaries
| ₹4.2 L/yr - ₹12 L/yr |
Deputy Manager
101
salaries
| ₹6 L/yr - ₹12.2 L/yr |
Junior Executive
60
salaries
| ₹2.2 L/yr - ₹4.5 L/yr |
Super Smelters
Ashapura Group Of Industries
TRL Krosaki Refractories
MN Dastur & Company