Filter interviews by
I appeared for an interview in Dec 2024.
An attitude test is a tool that measures a person's beliefs, values, and feelings about different aspects of life. It can also be used to assess a person's motivations and emotional intelligence.
Test to find out if someone has a natural ability for a particular type of work: I had to take an aptitude test before I began training as a nurse. SMART Vocabulary: related words and phrases.
Top trending discussions
posted on 1 Aug 2021
I applied via Campus Placement and was interviewed before May 2022. There were 2 interview rounds.
The number of parts in sfc panels varies depending on the specific panel and its design.
The number of parts can range from a few to several hundred.
Some common parts include solar cells, wiring, and protective coatings.
The number of parts can also depend on the size and power output of the panel.
Manufacturers may use different materials and designs, affecting the number of parts.
It is important to consider the number a...
Slip-ring motor speed can be controlled by varying the resistance in the rotor circuit.
Slip-ring motors have a wound rotor with external resistors.
By changing the resistance in the rotor circuit, the speed can be controlled.
This is done by adding or removing resistors from the rotor circuit.
The speed can also be controlled by changing the voltage applied to the stator.
This method is commonly used in industries where va...
Adding external resistance increases the total resistance in a circuit.
External resistance can be added in series or parallel to the existing circuit.
This can be useful in controlling the current flow and voltage drop in the circuit.
For example, adding a resistor in series with an LED can limit the current flowing through it and prevent it from burning out.
Similarly, adding a resistor in parallel with a component can r...
Main parts of eot cranes include bridge, trolley, hoist, end trucks, runway beams, and electrical components.
Bridge: main structure that spans the width of the bay
Trolley: carries the hoist and moves horizontally along the bridge
Hoist: lifts and lowers the load
End trucks: located on either side of the bridge and house the wheels for movement
Runway beams: support the crane and provide a path for the crane to travel alon...
Slip-ring motors are used in EOT cranes for their ability to provide high starting torque and smooth acceleration.
Slip-ring motors offer high starting torque, making them suitable for heavy loads in EOT cranes.
They provide smooth acceleration, reducing wear and tear on the crane components.
Slip-ring motors allow for speed control and reversing capabilities, important in crane operations.
These motors are also able to ha...
I applied via Approached by Company and was interviewed in Oct 2023. There was 1 interview round.
A starter control circuit is used to control the starting and stopping of an electric motor.
The starter control circuit typically includes a start button, stop button, overload relay, and contactor.
When the start button is pressed, it energizes the contactor which allows power to flow to the motor.
The overload relay protects the motor from overheating by sensing the current drawn by the motor.
The stop button breaks the...
To perform an id run test on a VFD, you need to follow specific steps to ensure the variable frequency drive is functioning correctly.
Connect the VFD to a motor and power supply
Set the VFD parameters according to the motor specifications
Run the motor at different speeds to test the VFD's ability to control the motor
Monitor the motor's performance and check for any abnormalities
Record the test results for analysis and t
I applied via Campus Placement
A transformer is a device that transfers electrical energy between two or more circuits through electromagnetic induction.
Transformers consist of two coils of wire, known as the primary and secondary coils.
When an alternating current flows through the primary coil, it creates a changing magnetic field which induces a voltage in the secondary coil.
Transformers are used to step up or step down voltage levels in electrica...
I applied via Campus Placement and was interviewed before Jan 2021. There was 1 interview round.
posted on 17 Feb 2024
I applied via Recruitment Consulltant and was interviewed in Sep 2023. There were 2 interview rounds.
I applied via Walk-in and was interviewed in May 2024. There was 1 interview round.
Rolling is a metal forming process in which a metal stock is passed through one or more pairs of rolls to reduce thickness and to make the thickness uniform.
Rolling is a metal forming process used to shape and reduce the thickness of metal stock.
It involves passing the metal through pairs of rolls that exert pressure to deform the metal.
Rolling can be hot rolling (done above the recrystallization temperature of the met...
Tensile test procedure involves applying a controlled tension force to a material sample to determine its mechanical properties.
Prepare the test specimen according to standards such as ASTM or ISO.
Secure the specimen in the testing machine grips.
Apply a gradually increasing tensile force until the specimen fractures.
Measure and record the force applied and the corresponding elongation of the specimen.
Calculate the tens...
Some of the top questions asked at the Neel Metal Products Electrical Technician interview -
based on 2 interviews
Interview experience
based on 3 reviews
Rating in categories
Senior Executive
186
salaries
| ₹3.2 L/yr - ₹7.2 L/yr |
Assistant Manager
182
salaries
| ₹4.2 L/yr - ₹12 L/yr |
Executive
172
salaries
| ₹1.9 L/yr - ₹6 L/yr |
Deputy Manager
99
salaries
| ₹6 L/yr - ₹12.5 L/yr |
Junior Executive
64
salaries
| ₹2 L/yr - ₹4.5 L/yr |
Super Smelters
Ashapura Group Of Industries
TRL Krosaki Refractories
MN Dastur & Company