Filter interviews by
I applied via Recruitment Consulltant and was interviewed in Jul 2023. There were 2 interview rounds.
The bolt to bolt distance depends on the specific design requirements and standards for the structural connection.
The bolt to bolt distance is typically specified in the design drawings or calculations provided by the engineer.
It is important to follow the recommended bolt to bolt distance to ensure the structural integrity of the connection.
The bolt to bolt distance may vary depending on factors such as the size and t...
Edge distance refers to the distance between the edge of a structural member and the center of a hole or fastener.
Edge distance is typically specified in design codes and standards.
It is important to maintain adequate edge distance to prevent failure of the connection.
The required edge distance can vary depending on the type of connection and the loading conditions.
For example, in steel connections, the minimum edge di...
The type of weld used for connecting a column to a base plate is typically a fillet weld.
Fillet welds are commonly used for connecting structural steel components.
The size of the fillet weld is determined based on the forces and stresses the connection will experience.
Proper welding procedures and inspections are essential to ensure the weld's quality and strength.
Column to beam joints are typically connected using various methods such as welding, bolting, or using mechanical connectors.
Common methods for connecting column to beam include welding, bolting, or using mechanical connectors
Welding is a common method where the column and beam are fused together using heat
Bolting involves using bolts to secure the column and beam together
Mechanical connectors such as shear connectors ...
The top moment column to beam top side is typically welded on the compression side of the beam.
Weld the top moment connection on the compression side of the beam for maximum strength.
Ensure proper welding techniques and inspections are followed to maintain structural integrity.
Consider using fillet welds or groove welds depending on the design requirements.
Consult structural engineering codes and standards for specific...
Edge distance of 75mm is required to cover vertical reinforcement in all types of foundations.
Edge distance is important to ensure proper anchorage and structural integrity of the reinforcement.
In this case, a minimum edge distance of 75mm is specified for covering vertical reinforcement in all types of foundations.
Examples of foundations where this requirement applies include spread footings, pile caps, and mat founda
I applied via Campus Placement and was interviewed in Sep 2024. There were 3 interview rounds.
General knowlegde, Basic Aptitude, Domain Technical MCQ
Genx vs Genz, Altitude and comparsion
Components of a transformer include core, windings, and insulation.
Core: Provides a path for magnetic flux
Windings: Primary and secondary coils for inducing voltage
Insulation: Prevents short circuits and ensures safety
I applied via Indeed and was interviewed in Mar 2024. There was 1 interview round.
Playing video after coming knowledge test
McDermott International interview questions for popular designations
General topics will be asked
Get interview-ready with Top McDermott International Interview Questions
I applied via Campus Placement and was interviewed in Oct 2024. There was 1 interview round.
I joined the company because of its innovative projects and collaborative work environment.
Opportunity to work on cutting-edge projects
Collaborative work environment
Company's reputation in the industry
Career growth opportunities
I applied via Recruitment Consulltant and was interviewed in Sep 2024. There were 2 interview rounds.
Timing punctuality,displain .
Suction piping of a pump is the piping system that brings fluid into the pump from the source.
Suction piping is designed to ensure a smooth flow of fluid into the pump without any air pockets or cavitation.
The piping should be sized appropriately to prevent excessive pressure drop and maintain efficient pump operation.
Proper alignment and support of the piping is crucial to prevent stress on the pump and ensure longevi...
Eccentric reducers are used in suction lines with flat side up to prevent air pockets and improve flow efficiency.
Eccentric reducers help in preventing air pockets from forming in the suction line
Having the flat side up ensures that any trapped air can easily escape
Improves flow efficiency by reducing turbulence and pressure drop
Commonly used in applications where smooth flow is critical, such as pump suction lines
Figure 8 is a type of knot commonly used in piping design to secure two ropes or cables together.
Figure 8 knot is also known as a stopper knot due to its ability to prevent ropes from slipping through holes or other openings.
It is easy to tie and untie, making it a popular choice for various applications in piping design.
The figure 8 knot is often used in rock climbing, sailing, and rescue operations for its reliabilit
Control station piping is essential for regulating and monitoring the flow of fluids in a system.
Control station piping connects various components such as valves, instruments, and equipment to control the flow of fluids.
Proper design of control station piping ensures efficient operation and safety of the system.
Consider factors like pressure, temperature, and material compatibility when designing control station pipin...
Suction piping of pump is crucial for efficient operation and performance.
Suction piping should be designed to minimize friction losses and ensure proper flow to the pump.
Proper sizing and layout of suction piping is essential to prevent cavitation and maintain pump efficiency.
Consider factors such as pipe diameter, length, bends, and fittings when designing suction piping.
Use smooth bore pipes, avoid sharp bends, and ...
Basic electronics and electrical questions
Topic is About GenC and GenX
I applied via Campus Placement and was interviewed in Dec 2023. There were 2 interview rounds.
Renewable resources speak atleast 20 minutes
Top trending discussions
Some of the top questions asked at the McDermott International interview -
The duration of McDermott International interview process can vary, but typically it takes about less than 2 weeks to complete.
based on 53 interviews
Interview experience
based on 637 reviews
Rating in categories
Piping Engineer
159
salaries
| â‚ą0 L/yr - â‚ą0 L/yr |
Electrical Designer
95
salaries
| â‚ą0 L/yr - â‚ą0 L/yr |
Piping Designer
89
salaries
| â‚ą0 L/yr - â‚ą0 L/yr |
Process Engineer
82
salaries
| â‚ą0 L/yr - â‚ą0 L/yr |
Structural Designer
79
salaries
| â‚ą0 L/yr - â‚ą0 L/yr |
TechnipFMC
Saipem
Subsea 7
Petrofac