20+ Jeeves Consumer Services Interview Questions and Answers

Interview questions for Structural Engineer

• For irregular shape, find volume and multiply by unit weight to get weight. Divide moment of each part by total weight to get COG.

• To calculate force required for COG shift, use moment equation. Sum of moments about any point should be equal to zero.

• For SFD and BMD, use equations of equilibrium and moment. Draw free body diagram to show all forces acting on the portal.

• Understand basic concepts of structural engineering such as moment,...read more

Barge and lifting analysis involves determining the support conditions and lifting factors for equipment on a barge.

• Barge and lifting analysis is used to ensure that equipment on a barge is properly supported and can be safely lifted.

• The procedure involves analyzing the support conditions of the barge and the equipment, as well as determining the lifting factors required to safely lift the equipment.

• Various factors must be considered, such as the weight and dimensions of the ...read more

Dynamic and static analysis of structures and foundations is essential for ensuring their stability and safety.

• Dynamic analysis involves studying the behavior of structures under dynamic loads such as earthquakes or wind.

• Static analysis focuses on the response of structures to static loads like gravity or applied forces.

• Both analyses help in determining the structural integrity, performance, and design optimization.

• Dynamic analysis techniques include modal analysis, response ...read more

Lighting levels for indoor and outdoor areas are determined based on the purpose of the space and the activities that take place.

• Indoor lighting levels are typically measured in foot-candles or lux

• Outdoor lighting levels are typically measured in lumens per square meter

• Calculation procedures involve determining the required illuminance level for the space and selecting appropriate light fixtures and bulbs

• Factors such as color rendering index, color temperature, and glare cont...read more

The type of weld used for connecting a column to a base plate is typically a fillet weld.

• Fillet welds are commonly used for connecting structural steel components.

• The size of the fillet weld is determined based on the forces and stresses the connection will experience.

• Proper welding procedures and inspections are essential to ensure the weld's quality and strength.

The top moment column to beam top side is typically welded on the compression side of the beam.

• Weld the top moment connection on the compression side of the beam for maximum strength.

• Ensure proper welding techniques and inspections are followed to maintain structural integrity.

• Consider using fillet welds or groove welds depending on the design requirements.

• Consult structural engineering codes and standards for specific welding requirements.

• Example: Weld the top moment connect...read more

Yes, I have experience using software such as ETABS, SAP2000, and SAFE. I have also worked with SACS.

• I have used ETABS for the design of high-rise buildings

• I have used SAP2000 for the analysis of complex structures

• I have used SAFE for the design of foundation systems

• I have experience working with SACS for offshore structures

The bolt to bolt distance depends on the specific design requirements and standards for the structural connection.

• The bolt to bolt distance is typically specified in the design drawings or calculations provided by the engineer.

• It is important to follow the recommended bolt to bolt distance to ensure the structural integrity of the connection.

• The bolt to bolt distance may vary depending on factors such as the size and type of bolts, the material being connected, and the load r...read more

Edge distance of 75mm is required to cover vertical reinforcement in all types of foundations.

• Edge distance is important to ensure proper anchorage and structural integrity of the reinforcement.

• In this case, a minimum edge distance of 75mm is specified for covering vertical reinforcement in all types of foundations.

• Examples of foundations where this requirement applies include spread footings, pile caps, and mat foundations.

Process loop type refers to the type of control loop used in a process control system.

• There are two main types of process loops: open loop and closed loop.

• Open loop systems do not have feedback control and rely on predetermined inputs.

• Closed loop systems use feedback control to adjust the process based on measured outputs.

• Examples of closed loop systems include PID control loops and cascade control loops.

A control valve is a device used to regulate the flow of fluid or gas in a system.

• Control valves are used in various industries such as oil and gas, chemical, and power generation.

• They can be operated manually or automatically through an actuator.

• Control valves can be classified based on their function, such as on/off valves or proportional valves.

• Examples of control valves include globe valves, ball valves, and butterfly valves.

Eccentric reducers are used in suction lines with flat side up to prevent air pockets and improve flow efficiency.

• Eccentric reducers help in preventing air pockets from forming in the suction line

• Having the flat side up ensures that any trapped air can easily escape

• Improves flow efficiency by reducing turbulence and pressure drop

• Commonly used in applications where smooth flow is critical, such as pump suction lines

Column to beam joints are typically connected using various methods such as welding, bolting, or using mechanical connectors.

• Common methods for connecting column to beam include welding, bolting, or using mechanical connectors

• Welding is a common method where the column and beam are fused together using heat

• Bolting involves using bolts to secure the column and beam together

• Mechanical connectors such as shear connectors or moment-resisting connections can also be used for joint...read more

Intool software is a software used for instrument data management and configuration.

• Intool software is used for managing and configuring instruments in various industries.

• It allows for easy data management and configuration of instruments.

• Intool software is commonly used in the oil and gas industry for managing and configuring instruments such as pressure gauges and flow meters.

Cable glands are used to secure and seal cables in various applications based on the area of installation.

• Cable glands are used in hazardous areas to prevent the entry of flammable gases and liquids.

• In outdoor applications, cable glands are used to protect cables from moisture and dust.

• In industrial settings, cable glands are used to secure cables and prevent them from being pulled out.

• Different types of cable glands are used for different types of cables, such as armored or ...read more

Edge distance refers to the distance between the edge of a structural member and the center of a hole or fastener.

• Edge distance is typically specified in design codes and standards.

• It is important to maintain adequate edge distance to prevent failure of the connection.

• The required edge distance can vary depending on the type of connection and the loading conditions.

• For example, in steel connections, the minimum edge distance is often specified as 1.5 times the diameter of the...read more

Site experience can be implemented with workers through effective communication, training, and leading by example.

• Regular toolbox talks to discuss site experience and safety measures

• Providing on-site training and refresher courses

• Encouraging workers to report any safety concerns or incidents

• Leading by example and following all safety protocols

• Incorporating site experience into daily work routines

• Providing incentives for safe work practices

• Conducting regular safety audits and ...read more

Yes, I have ISO9001-2015 Lead Auditor Certificate.

• I have completed the necessary training and passed the exam to obtain the certificate.

• I am familiar with the ISO9001-2015 standard and its requirements.

• I have experience conducting audits and ensuring compliance with the standard.

• Having the certificate demonstrates my commitment to quality management and continuous improvement.

Suction piping of a pump is the piping system that brings fluid into the pump from the source.

• Suction piping is designed to ensure a smooth flow of fluid into the pump without any air pockets or cavitation.

• The piping should be sized appropriately to prevent excessive pressure drop and maintain efficient pump operation.

• Proper alignment and support of the piping is crucial to prevent stress on the pump and ensure longevity.

• Filters or strainers may be installed in the suction pi...read more

During invoice processing, it is important to consider accuracy, completeness, and timeliness.

• Ensure all necessary information is included on the invoice

• Verify the accuracy of the amounts and calculations

• Match the invoice to the corresponding purchase order or contract

• Ensure timely processing to avoid late payment fees or missed discounts

Figure 8 is a type of knot commonly used in piping design to secure two ropes or cables together.

• Figure 8 knot is also known as a stopper knot due to its ability to prevent ropes from slipping through holes or other openings.

• It is easy to tie and untie, making it a popular choice for various applications in piping design.

• The figure 8 knot is often used in rock climbing, sailing, and rescue operations for its reliability and strength.

Quality assurance is the process of ensuring that a product or service meets the desired level of quality.

• It involves creating and implementing processes and procedures to prevent defects and errors.

• It includes testing and evaluating products or services to ensure they meet the required standards.

• It also involves continuous improvement to maintain and enhance the quality of the product or service.

• Examples include software testing, product inspections, and customer feedback an...read more

Components of a transformer include core, windings, and insulation.

• Core: Provides a path for magnetic flux

• Windings: Primary and secondary coils for inducing voltage

• Insulation: Prevents short circuits and ensures safety

Control station piping is essential for regulating and monitoring the flow of fluids in a system.

• Control station piping connects various components such as valves, instruments, and equipment to control the flow of fluids.

• Proper design of control station piping ensures efficient operation and safety of the system.

• Consider factors like pressure, temperature, and material compatibility when designing control station piping.

• Examples of control station piping include piping system...read more

Suction piping of pump is crucial for efficient operation and performance.

• Suction piping should be designed to minimize friction losses and ensure proper flow to the pump.

• Proper sizing and layout of suction piping is essential to prevent cavitation and maintain pump efficiency.

• Consider factors such as pipe diameter, length, bends, and fittings when designing suction piping.

• Use smooth bore pipes, avoid sharp bends, and ensure proper support to prevent vibration and stress on t...read more