Madhav Infra Projects Project Manager Interview Questions and Answers for Experienced

Bridges can be classified as major, minor or normal based on their importance and traffic volume.

• Major bridges are those that connect important cities or regions and have high traffic volume.

• Minor bridges are those that connect smaller towns or villages and have lower traffic volume.

• Normal bridges are those that fall in between major and minor bridges in terms of importance and traffic volume.

• Factors such as length, wi...read more

Pier is a vertical structure that supports the weight of a bridge, while abutment is a horizontal structure that supports the ends of a bridge.

• Pier is a vertical structure that supports the weight of a bridge, while abutment is a horizontal structure that supports the ends of a bridge.

• Piers are usually located in the middle of a bridge, while abutments are located at the ends of a bridge.

• Piers are typically made of con...read more

CA of river, nalla, local nalla can be found by studying the catchment area and rainfall data.

• Study the catchment area of the river, nalla, or local nalla

• Collect rainfall data of the area

• Calculate the runoff coefficient using the catchment area and rainfall data

• Multiply the runoff coefficient with the total rainfall to get the CA

• CA = Runoff Coefficient x Total Rainfall

• CA is important for designing drainage systems and

The density of cement is around 1440 kg/m³.

• Density of cement is the mass per unit volume of cement.

• It is measured in kg/m³ or g/cm³.

• The density of cement varies depending on the type of cement used.

• For example, the density of Portland cement is around 1440 kg/m³.

• The density of lightweight cement is around 1000 kg/m³.

The required compaction for dry lean concrete is specified by MORTH.

• MORTH specifies the minimum dry density and optimum moisture content for dry lean concrete.

• The compaction factor for dry lean concrete should be between 0.78 to 0.82.

• The compaction should be done using a plate vibrator or a needle vibrator.

• The required compaction can vary depending on the type of dry lean concrete being used.

• Proper compaction is import...read more

The design of Rigid Pavement is dependable on the type of traffic and the subgrade soil conditions.

• Traffic load and volume

• Subgrade soil conditions

• Climate and weather conditions

• Concrete mix design

• Joint spacing and layout

The percentage of slope in shoulder varies depending on the location and purpose of the shoulder.

• The slope of the shoulder can range from 0-45 degrees depending on the design of the road or pathway.

• The slope of the shoulder should be designed to allow for proper drainage and prevent water from pooling on the road.

• The slope of the shoulder should also be designed to provide a safe and stable surface for pedestrians and ...read more

The slope in normal camber varies depending on the design and purpose of the structure.

• Normal camber is the slight arching or upward curve given to a beam or truss to counteract deflection due to loads.

• The slope in normal camber can range from 1/8 inch to 1/2 inch per foot, depending on the span and load requirements.

• For example, a bridge beam may have a normal camber slope of 1/4 inch per foot to support heavy traffic...read more

The quantity of prime coat spread over WMM per sq. mt. depends on the type of bitumen extractor machine used.

• The quantity of prime coat depends on the type of bitumen extractor machine used

• It is important to follow the manufacturer's instructions for the specific machine being used

• Factors such as temperature, humidity, and surface condition can also affect the quantity of prime coat needed

• Typically, the quantity of pri...read more

The quantity of tack coat used over GSB per sq.mt. depends on various factors such as the type of bitumen extractor machine, the thickness of the GSB layer, and the weather conditions.

• The quantity of tack coat used can range from 0.2 to 0.5 liters per sq.mt.

• The type of bitumen extractor machine used can affect the quantity of tack coat used.

• The thickness of the GSB layer can also impact the quantity of tack coat used.

• W...read more