Add office photos
Filter interviews by
L&T Power Senior Safety Engineer Interview Questions and Answers
L&T Power Senior Safety Engineer Interview Experiences
1 interview found
Selected
I was interviewed before Aug 2022.
2. If any accident happened at site, workers mob collected at site. What your role during the accident.
(1 Question)
- Q1. 3. What is sling angle. How calculate the tension on sling during load lifting.
- Ans.
Sling angle refers to the angle between the sling and the horizontal plane. Tension on a sling during load lifting can be calculated using trigonometry.
Sling angle affects the tension on the sling - the greater the angle, the higher the tension.
To calculate the tension on a sling, you can use the formula Tension = Load / (2 * sin(angle)), where 'Load' is the weight being lifted and 'angle' is the sling angle.
It is impo...
Interview Preparation Tips
Top trending discussions
Interview questions from similar companies
I applied via Walk-in and was interviewed before Nov 2020. There was 1 interview round.
Interview Questionnaire
10 Questions
- Q1. What is the near miss?
- Ans.
A near miss is an unplanned event that has the potential to cause harm, loss, or damage but does not result in any injury or damage.
A near miss is a close call or a narrowly avoided accident.
It is an incident that could have resulted in injury, illness, or damage but did not.
Near misses are valuable opportunities to identify and address potential hazards before they cause harm.
Examples of near misses include a worker s...
- Q2. At what height safety belt are required?
- Ans.
Safety belts are required at heights where there is a risk of falling or injury.
Safety belts are required at heights above a certain threshold where there is a risk of falling or injury.
The specific height at which safety belts are required may vary depending on local regulations and industry standards.
Examples of heights where safety belts are commonly required include construction sites, rooftops, elevated platforms,...
- Q3. What is the colour of DA Cylinder?
- Ans.
The color of a DA Cylinder can vary depending on its contents.
The color of a DA Cylinder can be green, gray, or black.
A green DA Cylinder typically contains oxygen.
A gray or black DA Cylinder typically contains a mixture of gases, such as nitrogen and oxygen.
- Q4. What is the colour of oxygen cylinder?
- Q5. What is the length of safety belt?
- Ans.
The length of a safety belt varies depending on the type of belt and the intended use.
The length of a safety belt for a car typically ranges from 120 to 150 centimeters.
Safety belts for industrial purposes may have different lengths based on the specific requirements of the job.
Some safety belts are adjustable to accommodate different body sizes and shapes.
The length of a safety belt is designed to ensure proper fit an
- Q6. What is the dia of safety belt?
- Ans.
The diameter of a safety belt varies depending on the type and design.
The diameter of a safety belt can range from 1 inch to 2 inches.
Different types of safety belts may have different diameters.
For example, a standard seat belt in a car typically has a diameter of around 1.5 inches.
On the other hand, a safety harness used in construction may have a larger diameter of 2 inches.
The diameter of a safety belt is an import...
- Q7. What is MSDS ?
- Ans.
MSDS stands for Material Safety Data Sheet.
MSDS provides detailed information about the potential hazards, handling, storage, and emergency procedures for a specific chemical or product.
It includes information on physical and chemical properties, toxicity, health effects, first aid measures, and proper disposal methods.
MSDS is essential for ensuring the safe use, storage, and transportation of hazardous substances.
It h...
- Q8. What is the LTI?
- Ans.
LTI stands for Lost Time Injury.
LTI refers to any work-related injury or illness that results in an employee being unable to perform their regular job duties for a certain period of time.
It is a commonly used metric to measure the safety performance of an organization.
LTI is calculated by dividing the number of lost time injuries by the total number of hours worked and multiplying it by one million.
For example, if a co...
- Q9. What is scaffolding?
- Ans.
Scaffolding is a temporary structure used in construction to support workers and materials.
Scaffolding provides a safe working platform at different heights during construction or maintenance work.
It is typically made of metal pipes or tubes and wooden planks.
Scaffolding is erected around buildings, bridges, or other structures to facilitate construction, repair, or maintenance.
It must be designed, installed, and inspe...
- Q10. What is the I S Code of helmet?
- Ans.
The IS code for helmet is IS 4151:2015.
IS 4151:2015 is the Indian Standard code for protective helmets for two-wheeler riders.
It specifies the requirements and test methods for helmets to ensure safety and protection.
The code covers aspects like impact absorption, retention system, field of vision, and more.
Helmets meeting this standard provide assurance of quality and effectiveness in protecting the head.
Interview Preparation Tips
Very proud full moment.
(2 Questions)
- Q1. What is jsa with hazard
- Q2. What is risk
Interview Preparation Tips
I applied via Campus Placement and was interviewed in Aug 2024. There were 3 interview rounds.
Reasoning and numerical
(2 Questions)
- Q1. Tell me about your self
- Ans.
Experienced safety officer with a background in industrial safety protocols and risk management.
Over 5 years of experience in implementing safety procedures in industrial settings
Proficient in conducting safety audits and inspections
Skilled in developing and delivering safety training programs for employees
Strong knowledge of OSHA regulations and compliance standards
- Q2. What is your strength
- Ans.
My strength lies in my attention to detail and ability to identify potential safety hazards before they become a problem.
Strong attention to detail
Proactive in identifying safety hazards
Effective communication skills to address safety concerns
Ability to implement safety protocols and procedures
Experience in conducting safety inspections and audits
(2 Questions)
- Q1. What do you mean by Fire?
- Ans.
Fire is a rapid chemical reaction that releases heat, light, and various gases.
Fire is a result of the combustion process, where a fuel source combines with oxygen in the presence of heat to produce flames.
It requires three elements to sustain: fuel, oxygen, and heat.
Examples of fuel sources include wood, paper, gasoline, and natural gas.
Fire can be classified based on its fuel source, such as Class A (ordinary combust...
- Q2. What do you mean by safety
- Ans.
Safety refers to the measures taken to prevent accidents, injuries, and hazards in the workplace or any environment.
Safety involves identifying and assessing risks to prevent harm to individuals or property
It includes implementing safety protocols, procedures, and training to mitigate risks
Regular inspections and audits are conducted to ensure compliance with safety standards
Emergency preparedness and response plans ar...
Safety Manager Interview Questions & Answers
JSW Energy
R. Elangovan TSP SIIRM
posted on 27 Jul 2024
(2 Questions)
- Q1. Safety management
- Q2. Fire Department management
(2 Questions)
- Q1. Family background
- Q2. Children education
(2 Questions)
- Q1. Safety management
- Q2. Fire Department management
(2 Questions)
- Q1. Legal documents
- Q2. Role and responsibilities
Role and responsibilities
(2 Questions)
- Q1. Tell me about yourself
- Q2. What is the role and responsibilities
Interview Preparation Tips
DHARMENDRA SAHOO
(2 Questions)
- Q1. What is your favorite food
- Q2. Non veg all items
Aptitude test, reasoning test and English test
And technical
(4 Questions)
- Q1. Technical questions
- Q2. What is your role and responsibilities
- Ans.
The role of a Safety Officer is to ensure the safety and well-being of individuals in a workplace or environment.
Develop and implement safety policies and procedures
Conduct regular safety inspections and audits
Identify and assess potential hazards and risks
Train employees on safety protocols and emergency procedures
Investigate accidents and incidents, and provide recommendations for prevention
Maintain safety records an...
- Q3. What is PTW & type ofPTW
- Ans.
PTW stands for Permit to Work. It is a formal written system used to control high-risk activities in the workplace.
PTW is a document that outlines the work to be done, the hazards involved, and the necessary precautions.
It ensures that proper authorization and safety measures are in place before starting any high-risk task.
Different types of PTW include Hot Work Permit, Confined Space Entry Permit, Electrical Work Perm...
- Q4. Isolation and it's process
- Ans.
Isolation is the process of separating hazardous energy sources to protect workers from potential harm.
Isolation involves identifying and controlling energy sources.
The process includes de-energizing equipment, locking and tagging out energy sources, and verifying isolation.
Examples of isolation methods include electrical lockout/tagout, valve lockout/tagout, and confined space isolation.
Isolation procedures should be ...
Interview Preparation Tips
khalid Mehmood
I applied via By whatsapp and was interviewed in Apr 2022. There were 2 interview rounds.
(1 Question)
- Q1. Any type which related with safety
Interview Preparation Tips
L&T Power Interview FAQs
Tell us how to improve this page.
L&T Power Interviews By Designations
- L&T Power Graduate Engineer Trainee (Get) Interview Questions
- L&T Power Junior Engineer Trainee Interview Questions
- L&T Power Site Supervisor Interview Questions
- L&T Power AGM Interview Questions
- L&T Power Civil Foreman (Finishing) Interview Questions
- L&T Power Commissioning Manager Interview Questions
- L&T Power Designer Interview Questions
- L&T Power Diploma Trainee Engineer Interview Questions
- Show more
Interview Questions for Popular Designations
- Safety Engineer Interview Questions
- Safety Manager Interview Questions
- Senior Safety Officer Interview Questions
- Safety Officer Interview Questions
- Fire & Safety Officer Interview Questions
- Safety Supervisor Interview Questions
- Fire & Safety Supervisor Interview Questions
- Senior Safety Supervisor Interview Questions
- Show more
Interview Questions from Similar Companies
Fast track your campus placements
L&T Power Senior Safety Engineer Reviews and Ratings
based on 1 review
Rating in categories
|
Assistant Manager
210
salaries
|  ₹6.5 L/yr - ₹20 L/yr |
|
Senior Engineer
161
salaries
| ₹4.8 L/yr - ₹14 L/yr |
|
Manager
122
salaries
| ₹10 L/yr - ₹25 L/yr |
|
Assistant General Manager
72
salaries
| ₹19.5 L/yr - ₹30 L/yr |
|
Engineer
68
salaries
| ₹2.2 L/yr - ₹8.2 L/yr |
BHEL
Thermax Limited
Siemens
Tata Power
Calculate your in-hand salary
- Home >
- Interviews >
- L&T Power Interview Questions >
- L&T Power Senior Safety Engineer Interview Questions
