i
Intex Technologies
Filter interviews by
I applied via Referral and was interviewed before May 2023. There were 2 interview rounds.
Amplifiers are electronic devices that increase the strength of a signal.
Types of amplifiers include operational amplifiers, power amplifiers, and differential amplifiers.
Operational amplifiers are commonly used in signal processing and audio applications.
Power amplifiers are used to increase the power of a signal, such as in audio systems.
Differential amplifiers amplify the difference between two input signals.
Other t...
Logical gates are fundamental building blocks of digital circuits. They perform basic logic functions such as AND, OR, NOT, etc.
AND gate: output is high only if all inputs are high
OR gate: output is high if any input is high
NOT gate: output is the inverse of the input
NAND gate: combination of AND gate followed by NOT gate
NOR gate: combination of OR gate followed by NOT gate
XOR gate: output is high if inputs are differe
Top trending discussions
I applied via Campus Placement and was interviewed before Oct 2022. There were 3 interview rounds.
Yes, I am familiar with working as a PQC Engineer.
I have experience in performing quality control inspections on products
I am skilled in using various testing equipment and tools
I am knowledgeable about quality standards and procedures in manufacturing
I have worked on identifying and resolving quality issues in production processes
Questions related to Tree and stack
Questions related to Binary search
I applied via Naukri.com and was interviewed in Oct 2024. There were 3 interview rounds.
Any one technical questions from Electrical branch.
Current is the flow of electric charge in a circuit.
Current is measured in Amperes (A)
It is the rate of flow of electric charge through a conductor
There are two types of current - AC (alternating current) and DC (direct current)
Example: A light bulb connected to a battery has current flowing through it
Voltage is the difference in electric potential between two points in a circuit, measured in volts.
Voltage is the driving force that pushes electric current through a circuit
It is measured in volts (V)
Voltage can be positive or negative, depending on the direction of current flow
Higher voltage means more energy available to push current through a circuit
Examples: A battery provides voltage to power a flashlight, a wall...
Resistance is the opposition to the flow of electric current in a circuit.
Resistance is measured in ohms (Ω).
It is caused by the collisions of electrons with atoms in a material.
Higher resistance means lower current flow.
Examples of materials with high resistance include rubber and glass.
Examples of materials with low resistance include copper and silver.
I applied via Approached by Company and was interviewed in Jun 2024. There were 5 interview rounds.
Manager and technical officer
One split AC installation work explain
I applied via Campus Placement
AC is converted to DC using a rectifier circuit.
AC to DC conversion is done using a rectifier circuit, which converts alternating current (AC) to direct current (DC).
Rectifier circuits can be half-wave or full-wave, depending on the type of rectification needed.
Examples of rectifier circuits include diode rectifiers, bridge rectifiers, and voltage multiplier circuits.
Materials commonly used for earthing include copper, galvanized steel, and conductive concrete.
Copper rods
Galvanized steel rods
Conductive concrete
Earthing strips
Earthing plates
MCBA stands for Master of Construction Business Administration.
MCBA is a postgraduate degree program that focuses on the business aspects of the construction industry.
It covers topics such as project management, finance, marketing, and strategic planning.
Example: John completed his MCBA to advance his career in construction management.
The standard earthing voltage is typically 0 volts.
Standard earthing voltage is usually 0 volts to ensure safety in electrical systems
Earthing voltage can vary depending on the specific requirements of the system
Proper earthing helps to prevent electrical shocks and equipment damage
Design calculations for Sheetmetal involve determining material thickness, bend radius, and flat pattern development.
Calculate material thickness based on required strength and application
Determine bend radius to prevent cracking or deformation during bending process
Develop flat pattern layout to ensure accurate cutting and bending of sheetmetal
Consider factors like material type, sheet size, and manufacturing processe
I applied via Campus Placement and was interviewed in May 2024. There were 2 interview rounds.
The first round was an aptitude test, question ranging from medium to difficult .The marking scheme included -1,+1 for each incorrect and correct answer it was quite challenging . Additionally there were multiple-choice questions based on C++ output , which followed same marking scheme. Question were easy and most of the students were filtered out in this orund
I applied via Recruitment Consulltant and was interviewed in May 2024. There were 3 interview rounds.
Types of mortar in 2 phase include dry pack mortar and wet pack mortar.
Dry pack mortar is a stiff mixture of sand, cement, and water used for filling gaps and cracks.
Wet pack mortar is a fluid mixture of sand, cement, and water used for laying bricks and stones.
Other types of mortar include lime mortar, cement mortar, and epoxy mortar.
Language English Hindi
Assistant Manager
84
salaries
| ₹3.4 L/yr - ₹9 L/yr |
Deputy Manager
40
salaries
| ₹6 L/yr - ₹14 L/yr |
Senior Executive
34
salaries
| ₹3.1 L/yr - ₹5.5 L/yr |
Territory Sales Manager
27
salaries
| ₹3.6 L/yr - ₹6.5 L/yr |
Area Sales Manager
27
salaries
| ₹5 L/yr - ₹8.7 L/yr |
Micromax Informatics
Karbonn Mobile
Lava International
DiGiSPICE