Upload Button Icon Add office photos

Flowserve

Compare button icon Compare button icon Compare

Filter interviews by

Flowserve Drafting Engineer Interview Questions and Answers

Updated 11 Oct 2023

Flowserve Drafting Engineer Interview Experiences

1 interview found

Interview experience
3
Average
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Not Selected

I applied via Job Fair and was interviewed in Sep 2023. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(4 Questions)

  • Q1. Basic of engineering
  • Q2. What is pump and diffrent types
  • Ans. 

    A pump is a mechanical device used to move fluids from one place to another. There are various types of pumps including centrifugal, reciprocating, and rotary pumps.

    • Centrifugal pumps use a rotating impeller to create a flow of fluid.

    • Reciprocating pumps use a piston or diaphragm to displace the fluid.

    • Rotary pumps operate by trapping the fluid between rotating components.

    • Other types of pumps include gear pumps, screw pum

  • Answered by AI
  • Q3. What is your product name
  • Q4. From where do you come

Interview questions from similar companies

Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Recruitment Consulltant and was interviewed in Sep 2024. There was 1 interview round.

Round 1 - Technical 

(2 Questions)

  • Q1. Allowable stress values for tension, compression and shear?
  • Ans. 

    Allowable stress values vary depending on the material and type of loading (tension, compression, shear).

    • Allowable stress values are typically provided by material specifications or codes.

    • For example, for structural steel in tension, the allowable stress might be around 0.6 times the yield strength.

    • In compression, the allowable stress might be lower than in tension due to buckling considerations.

    • For shear, the allowabl...

  • Answered by AI
  • Q2. Which crane standard used for designing?
  • Ans. 

    The crane standard commonly used for designing is ASME B30.2.

    • ASME B30.2 is a widely recognized standard for designing cranes

    • It provides guidelines for the design, inspection, testing, maintenance, and operation of cranes

    • Other standards like ISO 4301 and CMAA also used in crane design

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Basic mechanical engineering questions and related to crane industry questions.
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
No response

I applied via Recruitment Consulltant and was interviewed in Apr 2024. There was 1 interview round.

Round 1 - Technical 

(3 Questions)

  • Q1. Refrigeration related questions
  • Q2. Stress and strain
  • Q3. Free body diagram of beam
  • Ans. 

    A free body diagram of a beam shows all external forces acting on the beam.

    • Identify all external forces acting on the beam such as gravity, applied loads, and reactions at supports.

    • Draw a simple sketch of the beam with arrows representing the direction and magnitude of each force.

    • Label each force with appropriate symbols or letters for clarity.

    • Ensure that the forces are correctly positioned and oriented relative to the

  • Answered by AI
Interview experience
3
Average
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Group Discussion 

About smart phone benifits and looses

Round 2 - Technical 

(2 Questions)

  • Q1. What is your interested subject?
  • Q2. What is your intership about?
Interview experience
3
Average
Difficulty level
Hard
Process Duration
More than 8 weeks
Result
-

I applied via Recruitment Consulltant and was interviewed in Mar 2024. There were 3 interview rounds.

Round 1 - One-on-one 

(1 Question)

  • Q1. Based on canditate experience
Round 2 - Tool test 

(1 Question)

  • Q1. Creo tool test is given
Round 3 - HR 

(1 Question)

  • Q1. Salary discussion, comapny overview

Interview Preparation Tips

Interview preparation tips for other job seekers - I had virtual face to face interview after i cleared, i gave virtual tool test.
After clearing this 2 rounds i had face to face with HR (Asia head), Reporting manager and his boss at office.
Work from office is cumpulsory though i gave virtual interviews.

Basically these company expects skilled canditate for less compensation. 18% will variable pay!! From the compensation you recieve. Which is given at year end based your performance, company performance..
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Not Selected

I applied via Recruitment Consulltant and was interviewed in May 2024. There was 1 interview round.

Round 1 - One-on-one 

(1 Question)

  • Q1. About current experience and special purpose machine design
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
2-4 weeks
Result
Not Selected

I applied via Referral and was interviewed before Sep 2023. There were 2 interview rounds.

Round 1 - Aptitude Test 

Questions on logical and quants

Round 2 - Technical 

(2 Questions)

  • Q1. What is Bernoulli principle?
  • Ans. 

    Bernoulli principle states that an increase in the speed of a fluid occurs simultaneously with a decrease in pressure or a decrease in the fluid's potential energy.

    • States that as the speed of a fluid increases, its pressure decreases

    • Used to explain lift in airplane wings

    • Applies to various fluid dynamics situations such as flow through pipes

  • Answered by AI
  • Q2. What is stress and how it can be measured?
  • Ans. 

    Stress is a force acting on a material that causes deformation. It can be measured using techniques like strain gauges and load cells.

    • Stress is a measure of the internal forces within a material resisting deformation.

    • It is typically measured in units of force per unit area, such as Pascals or pounds per square inch.

    • Common methods of measuring stress include strain gauges, load cells, and extensometers.

    • Stress can be cat...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Be strong at your basics
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
No response

I applied via LinkedIn and was interviewed in Oct 2022. There were 4 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Aptitude Test 

Questions from transducer digital electronics

Round 3 - Technical 

(1 Question)

  • Q1. Explain your project
Round 4 - HR 

(1 Question)

  • Q1. I didn't selected for HR round
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I was interviewed before May 2023.

Round 1 - Technical 

(3 Questions)

  • Q1. Som related questions
  • Q2. Sheet metal related questions
  • Q3. Tool test on solid works if you crack then get selected

Interview Preparation Tips

Interview preparation tips for other job seekers - Be geniune to HOD, move sharply

I applied via Recruitment Consultant and was interviewed in Jun 2021. There were 3 interview rounds.

Interview Questionnaire 

2 Questions

  • Q1. What is Packaging ?
  • Ans. 

    Packaging refers to the process of designing and creating the container or wrapping for a product.

    • Packaging protects the product during transportation and storage.

    • It also provides important information about the product, such as ingredients and usage instructions.

    • Packaging can be designed to attract customers and differentiate the product from competitors.

    • Examples of packaging materials include cardboard boxes, plastic

  • Answered by AI
  • Q2. Discuss about lot GD&T standards
  • Ans. 

    GD&T standards are used to define and communicate engineering tolerances and specifications.

    • GD&T stands for Geometric Dimensioning and Tolerancing

    • It is a system of symbols and rules used to specify the size, shape, and orientation of features on a part

    • GD&T standards are used to ensure that parts are manufactured to the correct specifications and can be assembled correctly

    • Examples of GD&T symbols include concentricity, ...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Prepare your best as per Job description

Skills evaluated in this interview

Flowserve Interview FAQs

How many rounds are there in Flowserve Drafting Engineer interview?
Flowserve interview process usually has 2 rounds. The most common rounds in the Flowserve interview process are Resume Shortlist and Technical.
What are the top questions asked in Flowserve Drafting Engineer interview?

Some of the top questions asked at the Flowserve Drafting Engineer interview -

  1. what is pump and diffrent ty...read more
  2. basic of engineer...read more

Tell us how to improve this page.

Flowserve Drafting Engineer Interview Process

based on 1 interview

Interview experience

3
  
Average
View more

Interview Questions from Similar Companies

Thermax Limited Interview Questions
4.1
 • 249 Interviews
Cummins Interview Questions
4.3
 • 231 Interviews
John Deere Interview Questions
4.1
 • 228 Interviews
Caterpillar Inc Interview Questions
4.3
 • 176 Interviews
Atlas Copco Interview Questions
4.2
 • 78 Interviews
TechnipFMC Interview Questions
4.0
 • 69 Interviews
TÜV SÜD Interview Questions
3.9
 • 60 Interviews
Hilti Interview Questions
3.5
 • 60 Interviews
View all

Flowserve Drafting Engineer Reviews and Ratings

based on 1 review

4.0/5

Rating in categories

3.0

Skill development

4.0

Work-life balance

3.0

Salary

4.0

Job security

3.0

Company culture

3.0

Promotions

3.0

Work satisfaction

Explore 1 Review and Rating
Design Engineer
457 salaries
unlock blur

₹2.6 L/yr - ₹11.1 L/yr

Associate Engineer
116 salaries
unlock blur

₹4.9 L/yr - ₹12 L/yr

Applications Engineer
99 salaries
unlock blur

₹4 L/yr - ₹13 L/yr

Junior Engineer
93 salaries
unlock blur

₹2.4 L/yr - ₹6 L/yr

Engineer
87 salaries
unlock blur

₹3.3 L/yr - ₹14 L/yr

Explore more salaries
Compare Flowserve with

Ksb Pumps

3.9
Compare

Forbes Marshall

4.1
Compare

Kirloskar Brothers

3.8
Compare

Grundfos Pumps

4.2
Compare
Did you find this page helpful?
Yes No
write
Share an Interview