Filter interviews by
Rate your
company
🤫 100% anonymous
How was your last interview experience?
I applied via Naukri.com and was interviewed in Mar 2023. There were 3 interview rounds.
Pressure is the force applied per unit area, while stress is the force applied per unit area of a material.
Pressure is a scalar quantity, while stress is a tensor quantity.
Pressure is measured in units of force per unit area, while stress is measured in units of force per unit area of a material.
Pressure is a measure of the external force applied to an object, while stress is a measure of the internal force within a ma...
Allied Engineers interview questions for popular designations
I applied via campus placement at University of Petroleum and Energy Studies (UPES), Dehradun and was interviewed before Nov 2023. There were 2 interview rounds.
Pythagoras theorem states that in a right-angled triangle, the square of the hypotenuse is equal to the sum of the squares of the other two sides.
In a right-angled triangle, the side opposite the right angle is called the hypotenuse.
The theorem can be written as a^2 + b^2 = c^2, where a and b are the other two sides and c is the hypotenuse.
This theorem is commonly used in engineering and physics to calculate distances
I applied via Recruitment Consulltant and was interviewed before May 2023. There were 5 interview rounds.
Various types of plastics are used in design engineering, each with unique properties and applications.
Common types include ABS, polycarbonate, polypropylene, and PVC
Each type has different strengths, flexibility, and heat resistance
Plastics are chosen based on factors like cost, durability, and desired properties
I applied via Referral and was interviewed before Jul 2022. There were 4 interview rounds.
General appitude related to department
I applied via Walk-in and was interviewed in Mar 2021. There was 1 interview round.
Types of cement include Portland cement, white cement, rapid hardening cement, and low heat cement.
Portland cement is the most commonly used type of cement and is used in general construction.
White cement is used for decorative purposes and has a high degree of whiteness.
Rapid hardening cement is used in projects where quick setting is required.
Low heat cement is used in large concrete projects to prevent cracking due
Cube size refers to the dimensions of a cube-shaped object.
Cube size is typically measured in length, width, and height.
It is commonly used in construction and engineering for materials such as concrete blocks.
For example, a standard concrete block may have a cube size of 8 inches by 8 inches by 8 inches.
Grade of cement refers to the strength of cement. It is classified into different grades based on its compressive strength.
Grade of cement is denoted by a number followed by Mpa (megapascal)
The higher the grade, the higher the compressive strength of cement
For example, grade 53 cement has a compressive strength of 53 Mpa
Different grades of cement are used for different construction purposes
There is no formula for steel, but its properties can be calculated using various equations.
Steel is an alloy of iron and carbon, with other elements added for specific properties.
The properties of steel can be calculated using equations such as Young's modulus, Poisson's ratio, and thermal expansion coefficient.
The strength of steel can be calculated using the ultimate tensile strength formula.
Steel's corrosion rate c...
Top trending discussions
posted on 9 Oct 2024
I applied via Referral and was interviewed in Sep 2024. There was 1 interview round.
The main reason for belt joint failure is usually due to improper installation or maintenance.
Improper installation of the belt joint, such as incorrect alignment or tensioning
Lack of proper maintenance, leading to wear and tear of the joint
Use of low-quality materials for the joint
Excessive load or stress on the belt joint
Environmental factors like temperature or humidity affecting the joint
The alignment maximum tolerance refers to the maximum allowable deviation from the specified alignment.
Alignment maximum tolerance is the maximum allowable deviation from the specified alignment.
It is typically expressed in terms of a percentage or a specific measurement unit.
For example, a machine part may have an alignment maximum tolerance of +/- 0.005 inches.
Exceeding the alignment maximum tolerance can lead to per
To replace the bucket wheel reclaimer luffing cylinder, follow these steps.
1. Shut down the machine and ensure all power sources are disconnected.
2. Remove any surrounding components that may obstruct access to the luffing cylinder.
3. Use appropriate tools to disconnect the hydraulic hoses and fittings from the cylinder.
4. Support the weight of the cylinder as it is removed to prevent damage to surrounding components.
5...
JSA stands for Job Safety Analysis, focusing on specific job tasks, while HIRA stands for Hazard Identification and Risk Assessment, focusing on overall workplace hazards.
JSA is task-specific, focusing on individual job tasks and potential hazards
HIRA is broader, looking at overall workplace hazards and assessing risks
JSA involves breaking down a job into steps and identifying potential hazards for each step
HIRA involv...
To create a PR in SAP, you can use transaction code ME51N or ME21N.
Use transaction code ME51N to create a purchase requisition in SAP.
Enter the necessary details such as material, quantity, delivery date, etc.
Save the purchase requisition and it will be created in the system.
Alternatively, you can also use transaction code ME21N to create a purchase order directly.
The procedure of pulley replacement involves identifying the faulty pulley, removing the old pulley, installing the new pulley, and testing the system.
Identify the faulty pulley by checking for any signs of wear or damage.
Use appropriate tools to remove the old pulley, such as a pulley puller or wrench.
Install the new pulley by aligning it properly and securing it in place.
Test the system to ensure the new pulley is fu...
PTW stands for Permit to Work, a procedure used to ensure that work is carried out safely in potentially hazardous environments.
PTW is a formal written system used to control certain types of work that are identified as potentially hazardous.
Before starting work, a permit must be obtained from a designated authority.
The permit outlines the work to be done, the hazards involved, and the necessary precautions to be taken...
I applied via Job Portal and was interviewed in Dec 2024. There was 1 interview round.
based on 13 interviews
Interview experience
Anonymously discuss salaries, work culture, and many more
Get Ambitionbox App
based on 74 reviews
Rating in categories
Project Engineer
20
salaries
| â‚ą3 L/yr - â‚ą5.5 L/yr |
Quality Engineer
10
salaries
| â‚ą2.4 L/yr - â‚ą5 L/yr |
Production Engineer
8
salaries
| â‚ą2.1 L/yr - â‚ą4 L/yr |
Biomedical Engineer
7
salaries
| â‚ą2.1 L/yr - â‚ą4.5 L/yr |
Senior Sales Executive
7
salaries
| â‚ą3.2 L/yr - â‚ą4.8 L/yr |
Larsen & Toubro Limited
Thermax Limited
BHEL
TCS