Filter interviews by
I have 5 years of experience working as a Site Engineer in construction projects.
5 years of experience as a Site Engineer
Managed construction projects from start to finish
Ensured compliance with safety regulations and quality standards
Collaborated with architects, contractors, and other stakeholders
Performed site inspections and resolved technical issues
General aptitude, english
Expectations of necessities for a Site Engineer
Clear project scope and objectives
Adequate budget and resources
Effective communication with stakeholders
Access to necessary equipment and materials
Compliance with safety regulations
Timely resolution of issues and conflicts
I appeared for an interview in Aug 2019.
There are various types of structures, including buildings, bridges, dams, tunnels, and towers.
Structures can be classified based on their purpose, design, and materials used.
Buildings can be further classified into residential, commercial, and industrial structures.
Bridges can be classified into beam, arch, suspension, and cable-stayed bridges.
Dams can be classified into gravity, arch, buttress, and embankment dams.
Tu...
Density is the measure of mass per unit volume of a substance.
It is a physical property of matter.
It is calculated by dividing the mass of a substance by its volume.
Units of density include kg/m³, g/cm³, and lb/ft³.
Density can be used to identify substances and determine their purity.
For example, gold has a density of 19.3 g/cm³, while aluminum has a density of 2.7 g/cm³.
There are two types of density construction: compacted and loose.
Compacted density construction involves compressing the material to increase its density, such as in road construction.
Loose density construction involves leaving the material in its natural state, such as in landscaping.
The type of density construction used depends on the intended use of the material and the desired level of compaction.
Other factors that...
Tests for construction joints include visual inspection, water tightness test, and load transfer test.
Visual inspection to check for proper joint alignment and sealant application
Water tightness test to ensure no water leakage through the joint
Load transfer test to verify the joint can handle the intended load
Other tests may include pull-out test, shear test, and compression test
Testing frequency and methods may vary d...
posted on 20 Dec 2020
posted on 16 Sep 2022
I applied via Company Website and was interviewed in Aug 2022. There was 1 interview round.
Slump test is a measure of the consistency of fresh concrete.
It is used to determine the workability of concrete.
The test involves filling a standard cone-shaped container with concrete and then removing the cone to see how much the concrete slumps or settles.
The amount of slump is measured in millimeters and indicates the wetness or dryness of the concrete.
Curing is the process of maintaining moisture in the concrete ...
posted on 29 Jan 2021
posted on 30 Aug 2021
I applied via Naukri.com and was interviewed in Aug 2021. There were 3 interview rounds.
posted on 1 Oct 2023
I applied via Walk-in and was interviewed in Apr 2023. There were 3 interview rounds.
I applied via Campus Placement and was interviewed before May 2023. There was 1 interview round.
Design mix concrete is a mix of concrete prepared by a designer as per the required strength and durability, while nominal mix concrete is a mix of concrete prepared based on standard ratios without specific design requirements.
Design mix concrete is prepared by a designer based on specific requirements for strength and durability.
Nominal mix concrete is prepared based on standard ratios like 1:2:4 without specific des...
Knee bracing is a structural support used in construction to prevent lateral movement of beams or columns.
Knee bracing is a diagonal member used to connect a vertical member to a horizontal member in a structure.
It helps to resist lateral forces and prevent buckling or swaying of the structure.
Knee bracing is commonly used in steel frame construction to provide stability and support.
Examples include diagonal braces con
based on 2 interviews
Interview experience
based on 28 reviews
Rating in categories
Field Engineer
147
salaries
| ₹1.7 L/yr - ₹7 L/yr |
Civil Engineer
145
salaries
| ₹2.4 L/yr - ₹9.6 L/yr |
Electrical Engineer
81
salaries
| ₹2.4 L/yr - ₹8.4 L/yr |
Site Engineer
71
salaries
| ₹2 L/yr - ₹5.5 L/yr |
Civil Site Engineer
66
salaries
| ₹2.2 L/yr - ₹6 L/yr |
L&T Construction
Simplex Infrastructures
AECOM
L&T Energy Hydrocarbon