Tata Steel Junior its Engineer Interview Questions and Answers

Q1. How to check the motor
Ans. 
To check the motor, you can perform various tests and inspections to ensure it is functioning properly.
• Check for any physical damage or wear on the motor casing

• Inspect the wiring connections for any loose or damaged wires

• Measure the voltage and current going into the motor to ensure it is within the specified range

• Test the motor's insulation resistance to check for any faults

• Run the motor under load to see if it operat
Answered by AI
Add your answer
Q2. How to do power analysis
Ans. 
Power analysis involves measuring and analyzing the electrical power consumption of a system or device.
• Identify the components of the system or device that consume power.

• Measure the current and voltage across these components using appropriate instruments.

• Calculate the power consumption using the formula P = VI, where P is power, V is voltage, and I is current.

• Analyze the power consumption data to identify any ineffici...read more
Answered by AI
Add your answer
Q3. What is tranfamer
Ans. 
A transformer is a device that transfers electrical energy between two or more circuits through electromagnetic induction.
• Transformers are used to increase or decrease voltage levels in electrical circuits.

• They consist of two coils of wire, known as the primary and secondary coils.

• Examples of transformers include power transformers used in electrical substations and voltage transformers in electronic devices.
Answered by AI
Add your answer

Q1. Types of welding
Ans. 
Types of welding include MIG, TIG, stick, and flux-cored welding.
• MIG welding uses a wire electrode and shielding gas.

• TIG welding uses a tungsten electrode and inert gas.

• Stick welding uses a consumable electrode coated in flux.

• Flux-cored welding uses a tubular wire filled with flux.

• Other types include spot welding, laser welding, and resistance welding.
Answered by AI
Add your answer
Q2. Engeneering Material also read
Add your answer

Q1. What is Dynamic Viscosity?
Ans. 
Dynamic viscosity is a measure of a fluid's resistance to flow under applied force.
• Dynamic viscosity is also known as absolute viscosity.

• It is a measure of how thick or thin a fluid is.

• Units of dynamic viscosity are Pascal-seconds (Pa·s) or Poise (P).

• Water has a dynamic viscosity of about 0.001 Pa·s at room temperature.
Answered by AI
Add your answer
Q2. Draw the stress strain diagram.
Ans. 
The stress-strain diagram shows the relationship between stress and strain in a material.
• The stress-strain diagram typically consists of a linear elastic region, a yield point, and a plastic deformation region.

• The slope of the linear elastic region represents the material's Young's Modulus.

• The yield point indicates the stress at which the material begins to deform plastically.

• The ultimate tensile strength is the maximu...read more
Answered by AI
Add your answer

Q1. Ask me about types of bearings? They also like do you have any idea about sap?
Add your answer
Q2. Ask me about types of bearing? What is the types of welding? About sap?
Add your answer

Q1. Blust furnace, Quantitative analysis of Fe, molecular wt of Fe, iron ores, basic knowledge about chemicals and chemical glassware.
Add your answer

Q1. Your aim, strength and weakness, hobby etc.
Add your answer
Q2. Expectation salary, are you able to relocate
Add your answer

Be confident in your answer and no more confusing. Think twice, answer Little bit similar but u have to choose one it has a more accurate. Time management is main. What time you did taken to answer for each question.

Talk short with important matter. Your voice should to audible for all.

Q1. This is related to your study. Befor going to interview first you should know the which type of company that is and what they produce. Go to the deep through it on this basis you have to prepare.
Add your answer
Q2. Sketch the Lathe diagram Stress strain diagram About Boiler About hydraulic system About pneumatic system About engines About machanical properties Project principles About manpower handling
Add your answer