Filter interviews by
Clear (1)
I applied via Campus Placement and was interviewed before Feb 2020. There were 5 interview rounds.
The interview covered topics such as differences between petrol and diesel engines, laws of thermodynamics, types of fluids, and DC motor working.
Petrol engines use spark plugs to ignite fuel, while diesel engines use compression to ignite fuel
The first law of thermodynamics states that energy cannot be created or destroyed, only transferred or converted
Fluids can be classified as liquids, gases, or plasmas
My hobbies i...
Rate your
company
🤫 100% anonymous
How was your last interview experience?
Top trending discussions
I applied via Company Website and was interviewed in Feb 2024. There were 2 interview rounds.
TELL ME ABOUT YOUR SELF /..' ;;; AND WHT IS PAINT PIGMENT /PH VALUE
Technical and general knowledge
I applied via Walk-in and was interviewed before Nov 2020. There was 1 interview round.
A circuit breaker is an electrical switch that automatically interrupts the flow of current when it exceeds a certain limit.
It is used to protect electrical circuits from damage caused by overloading or short circuits.
It works by detecting the excess current and tripping the switch to break the circuit.
It can be reset manually or automatically depending on the type of circuit breaker.
Examples include thermal circuit br...
A contactor is an electrical switch used for switching an electrical circuit on or off.
It is used to control electric motors, lighting, heating, and other electrical loads.
It consists of a coil, contacts, and an enclosure.
The coil generates a magnetic field that pulls the contacts together to close the circuit.
Examples include HVAC systems, elevators, and industrial machinery.
Contactor ratings are based on the amount o...
MCB stands for Miniature Circuit Breaker. It is an electrical switch that automatically shuts off the electrical circuit during an overload or short circuit.
MCB is a type of circuit breaker that is commonly used in residential and commercial buildings.
It is designed to protect electrical circuits from damage caused by overloading or short circuits.
MCBs are available in different current ratings and can be easily replac...
A motor is a device that converts electrical energy into mechanical energy to produce motion.
Motors are used in various applications such as electric vehicles, industrial machinery, and household appliances.
There are different types of motors such as DC motors, AC motors, stepper motors, and servo motors.
The basic principle of a motor is the interaction between a magnetic field and an electric current.
Examples of motor...
A current transformer is a device that measures the current flowing in a circuit by producing a proportional current in its secondary winding.
Consists of a primary winding and a secondary winding
Primary winding is connected in series with the circuit carrying the current to be measured
Secondary winding is connected to a measuring instrument or protective relay
Produces a current in the secondary winding that is proporti...
I was interviewed in Dec 2016.
A two-stroke engine completes a power cycle in two strokes of the piston, while a four-stroke engine completes it in four strokes.
Two-stroke engines have a simpler design and are lighter than four-stroke engines.
Two-stroke engines have a higher power-to-weight ratio but lower fuel efficiency compared to four-stroke engines.
Four-stroke engines have separate intake, compression, power, and exhaust strokes, while two-stro...
A pictorial representation of a SI engine with valve opening, TDC, and BDC.
SI engine stands for Spark Ignition engine, which is commonly used in gasoline-powered vehicles.
Valve opening refers to the movement of the intake and exhaust valves to allow fuel-air mixture in and exhaust gases out of the combustion chamber.
TDC (Top Dead Center) is the position of the piston at the extreme top of its stroke.
BDC (Bottom Dead Ce...
I would improve the fuel efficiency of TVS motorcycles by implementing advanced engine technology.
Implementing electronic fuel injection system for better fuel management
Introducing hybrid technology for improved mileage
Optimizing aerodynamics of the motorcycle for reduced drag
Using lightweight materials for better fuel economy
I am a dedicated production engineer with a strong background in manufacturing processes and quality control.
Graduated with a degree in Mechanical Engineering
Experience working in a manufacturing plant for 3 years
Proficient in CAD software for designing production layouts
Implemented lean manufacturing principles to improve efficiency
Led a team in reducing production downtime by 20%
I applied via Campus Placement and was interviewed before Aug 2021. There were 4 interview rounds.
20 marks objective questions for aptitude test
I applied via Campus Placement and was interviewed before May 2020. There was 1 interview round.
I applied via Referral and was interviewed before Jan 2020. There were 3 interview rounds.
I applied via Naukri.com and was interviewed in Jan 2023. There were 2 interview rounds.
Junior Manager
80
salaries
| ₹0 L/yr - ₹0 L/yr |
Area Service Manager
73
salaries
| ₹0 L/yr - ₹0 L/yr |
Area Sales Manager
69
salaries
| ₹0 L/yr - ₹0 L/yr |
Assistant Manager
62
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Executive
61
salaries
| ₹0 L/yr - ₹0 L/yr |
Honda
Yamaha Motor
India Kawasaki Motors Pvt. Ltd.
TVS Motor