Upload Button Icon Add office photos

Filter interviews by

Clear (1)

Sheltera Consultants Junior Engineer Civil Interview Questions, Process, and Tips

Updated 12 Jul 2021

Sheltera Consultants Junior Engineer Civil Interview Experiences

1 interview found

I applied via Campus Placement and was interviewed in Jun 2021. There were 4 interview rounds.

Interview Questionnaire 

4 Questions

  • Q1. What is the Nominal mix and design mix ?
  • Ans. 

    Nominal mix is a mix of fixed proportions of cement, sand and aggregate. Design mix is a mix of desired proportions of cement, sand and aggregate.

    • Nominal mix is used for small construction works and where quality control is not a major concern.

    • Design mix is used for large construction works and where quality control is a major concern.

    • Nominal mix has fixed proportions of materials, usually 1:2:4 for M15 grade concrete.

    • ...

  • Answered by AI
  • Q2. What is NDT test?
  • Ans. 

    NDT stands for Non-Destructive Testing. It is a type of testing that does not damage the material being tested.

    • NDT is used to detect defects or irregularities in materials without causing damage.

    • It is commonly used in industries such as aerospace, construction, and manufacturing.

    • Some common NDT methods include ultrasonic testing, radiography, and magnetic particle testing.

    • NDT is important for ensuring the safety and re...

  • Answered by AI
  • Q3. How to calculate material of M20 grade concrete? And ratio
  • Ans. 

    To calculate material of M20 grade concrete, we need to know the ratio of cement, sand, and aggregate.

    • M20 grade concrete has a mix proportion of 1:1.5:3 of cement, sand, and aggregate respectively.

    • To calculate the quantity of each material, we need to know the volume of concrete required.

    • Assuming the volume of concrete required is 1 cubic meter, the quantity of cement required would be 0.28 cubic meters.

    • The quantity of...

  • Answered by AI
  • Q4. How to perform cement finesse test and final setting time and initial setting time
  • Ans. 

    Cement finesse test measures the particle size of cement. Initial and final setting time tests measure the time taken for cement to set.

    • For cement finesse test, a sample of cement is sieved through a standard sieve and the residue is weighed.

    • The residue is then sieved through a finer sieve and the weight of the residue is again measured.

    • The difference between the two weights gives the fineness of cement.

    • For initial and...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - You have basic civil test information like as cube test, seive analysis, NDT test, design mix concrete

Interview questions from similar companies

Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I was interviewed in Jul 2023.

Round 1 - Technical 

(5 Questions)

  • Q1. Types of bricks. Types of concrete.
  • Ans. 

    Bricks can be classified as clay bricks, concrete bricks, and fly ash bricks. Concrete can be classified as normal concrete, high-strength concrete, and lightweight concrete.

    • Types of bricks: clay bricks, concrete bricks, fly ash bricks

    • Types of concrete: normal concrete, high-strength concrete, lightweight concrete

  • Answered by AI
  • Q2. 2 Types of bricks.3 Types of concrete.
  • Ans. 

    Bricks: Burnt clay bricks, Fly ash bricks. Concrete: Plain concrete, Reinforced concrete, Prestressed concrete.

    • Bricks: Burnt clay bricks are made by burning clay in a kiln. Fly ash bricks are made from fly ash, lime, and gypsum.

    • Concrete: Plain concrete is a mixture of cement, sand, and aggregate. Reinforced concrete has steel bars embedded in it for added strength. Prestressed concrete is pre-compressed to reduce crack...

  • Answered by AI
  • Q3. Types of foundation andit's used
  • Ans. 

    Types of foundations include shallow, deep, and special foundations, each used based on soil conditions and structural requirements.

    • Shallow foundations: spread footings, mat foundations, strip footings

    • Deep foundations: piles, drilled piers, caissons

    • Special foundations: raft foundations, pile caps, underpinning

    • Used based on soil conditions, building loads, and site constraints

  • Answered by AI
  • Q4. Types of collum and it's used
  • Ans. 

    Types of columns include reinforced concrete columns, steel columns, composite columns, and wooden columns.

    • Reinforced concrete columns are commonly used in building construction for their strength and durability.

    • Steel columns are often used in industrial structures due to their high load-bearing capacity.

    • Composite columns combine materials like steel and concrete for optimal performance.

    • Wooden columns are used in tradi...

  • Answered by AI
  • Q5. Types of slab and it's used
  • Ans. 

    Types of slabs include one-way slab, two-way slab, flat slab, and ribbed slab, each used for different purposes.

    • One-way slab: used for small spans and supported on two opposite sides.

    • Two-way slab: used for larger spans and supported on all four sides.

    • Flat slab: used for heavy loads and provides more flexibility in design.

    • Ribbed slab: used for longer spans and reduces the weight of the slab.

  • Answered by AI
Interview experience
5
Excellent
Difficulty level
Easy
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Approached by Company and was interviewed in Mar 2023. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all Resume tips
Round 2 - Technical 

(8 Questions)

  • Q1. What is the Full form of TMT
  • Ans. 

    TMT stands for Thermo-Mechanically Treated reinforcement bars used in construction.

    • TMT bars are made by subjecting mild steel bars to a combination of heat treatment and mechanical deformation.

    • This process imparts greater strength and ductility to the bars, making them ideal for use in construction.

    • TMT bars are widely used in reinforced concrete structures such as buildings, bridges, and dams.

    • They offer superior corros...

  • Answered by AI
  • Q2. What is the 500DMeans at TMT bars?
  • Ans. 

    500D means the yield strength of TMT bars is 500 MPa.

    • 500D is a grade of TMT bars used in construction.

    • The 'D' stands for ductility, which is the ability of the material to deform without breaking.

    • The yield strength of 500D TMT bars is 500 MPa.

    • These bars are commonly used in high-rise buildings, bridges, and other structures that require high strength and durability.

  • Answered by AI
  • Q3. What is the required steel at the percentage concrete?
  • Ans. 

    The required steel at the percentage concrete depends on the design and specifications of the structure.

    • The amount of steel reinforcement needed in concrete is determined by the design and specifications of the structure.

    • Factors such as the size and shape of the structure, the loads it will bear, and the desired strength and durability of the concrete will all affect the required steel percentage.

    • The steel percentage c...

  • Answered by AI
  • Q4. What is the stress and strain?
  • Ans. 

    Stress is the force applied per unit area, while strain is the deformation caused by stress.

    • Stress is a measure of the internal forces within a material, while strain is the measure of the deformation of the material.

    • Stress is expressed in units of force per unit area, while strain is expressed as a ratio of the change in length or shape to the original length or shape.

    • Stress and strain are related by the material's el...

  • Answered by AI
  • Q5. Which type of stress failure at brick wall?
  • Ans. 

    The stress failure at brick wall can be due to compressive or tensile stress.

    • Compressive stress failure occurs when the brick wall is unable to withstand the weight or load placed on it.

    • Tensile stress failure occurs when the brick wall is unable to withstand the forces that pull it apart.

    • Cracking, bulging, or collapse of the wall can be signs of stress failure.

    • Reinforcing the wall with steel bars or using thicker brick

  • Answered by AI
  • Q6. White marvel is this rock?
  • Ans. 

    White marble is a metamorphic rock composed of recrystallized carbonate minerals, mainly calcite or dolomite.

    • It is commonly used in construction and sculpture.

    • It is formed from limestone or dolomite that has undergone heat and pressure.

    • It is often found in quarries in countries such as Italy, Greece, and India.

  • Answered by AI
  • Q7. What is myka sis ?
  • Q8. Standerd Coarse sand size?
  • Ans. 

    Standard coarse sand size ranges from 2.0mm to 4.75mm.

    • Standard coarse sand is commonly used in construction and civil engineering projects.

    • It is typically graded between 2.0mm to 4.75mm in size.

    • This type of sand is often used as a base material for concrete and asphalt.

    • It can also be used for drainage systems and as a bedding material for pipes.

    • The size and shape of the sand particles can affect the strength and durabi

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Up above these questions are very good. Very much challenge when you have few time period of project, vast priority of project,and contractors are unidentified what is doing the job first to last .
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
4-6 weeks
Result
Selected Selected

I applied via Naukri.com and was interviewed before Jan 2023. There was 1 interview round.

Round 1 - Technical 

(5 Questions)

  • Q1. Size of slump cone
  • Ans. 

    The size of a slump cone is a tool used in concrete testing to measure the consistency of fresh concrete.

    • The size of a slump cone is typically 12 inches in height.

    • The base diameter of a slump cone is usually 8 inches.

    • The top diameter of a slump cone is typically 4 inches.

    • The size of a slump cone may vary depending on specific testing requirements or standards.

    • The dimensions of a slump cone are important for accurate me...

  • Answered by AI
  • Q2. Estimation of aggregate quantity for 200sqmt slab
  • Ans. 

    To estimate aggregate quantity for a 200sqmt slab, calculate the volume of concrete required and then determine the aggregate quantity based on the mix ratio.

    • Calculate the volume of concrete required for the slab

    • Determine the mix ratio of concrete (e.g., 1:2:4)

    • Calculate the volume of aggregates needed based on the mix ratio

    • Consider the bulk density of aggregates to convert volume to weight

    • Account for wastage and add a

  • Answered by AI
  • Q3. What are previous quality we need to check before casting
  • Ans. 

    Before casting, civil engineers need to check the quality of various elements.

    • Quality of concrete mix

    • Quality of reinforcement bars

    • Quality of formwork

    • Quality of water used in the mix

    • Quality of curing process

  • Answered by AI
  • Q4. How many cubes we have to take for 250cum concrete
  • Ans. 

    The number of cubes required for 250 cubic meters of concrete depends on the size of the cubes.

    • The size of the cubes needs to be specified to determine the number required.

    • The volume of each cube needs to be calculated.

    • Divide the total volume of concrete (250 cubic meters) by the volume of each cube to get the number of cubes required.

    • For example, if the cubes are 1 cubic meter in size, then 250 cubes would be needed.

  • Answered by AI
  • Q5. Post concrete quality inspection?
  • Ans. 

    Post concrete quality inspection involves evaluating the quality of concrete after it has been placed and hardened.

    • Inspect the concrete for any visible defects such as cracks, honeycombing, or segregation.

    • Check the concrete strength by conducting compressive strength tests on samples taken from the structure.

    • Assess the concrete's durability by examining its resistance to factors like freeze-thaw cycles or chemical expo...

  • Answered by AI

I applied via Referral and was interviewed in Sep 2021. There were 3 interview rounds.

Interview Questionnaire 

5 Questions

  • Q1. What increase do you expect?
  • Ans. 

    I expect a 10% increase in my salary.

    • I have consistently exceeded performance targets in my current role.

    • I have completed additional training and certifications to enhance my skills.

    • I have researched industry standards and determined that a 10% increase is reasonable.

    • I have received positive feedback from colleagues and supervisors on my work.

    • I have been with the company for several years and have taken on additional r

  • Answered by AI
  • Q2. Why are you looking for job change?
  • Q3. How will you ensure EHS pertaining to Civil works in a fast track Industrial Project?
  • Ans. 

    Ensuring EHS in fast track Industrial Project for Civil works requires strict adherence to safety protocols and regular monitoring.

    • Implementing a comprehensive EHS plan specific to Civil works

    • Conducting regular safety training sessions for all workers and contractors

    • Ensuring proper use of personal protective equipment (PPE) at all times

    • Regularly inspecting the work site for potential hazards and taking corrective actio...

  • Answered by AI
  • Q4. What is slip form and tell one critical operational issue related to it?
  • Ans. 

    Slip form is a method of continuous concrete placement using a moving formwork system.

    • Slip form is commonly used in the construction of tall structures such as towers and bridges.

    • One critical operational issue related to slip form is maintaining the proper concrete consistency to ensure smooth and uniform pouring.

    • If the concrete consistency is not properly maintained, it can lead to issues such as segregation, which ca...

  • Answered by AI
  • Q5. What is fullform of HIRA?
  • Ans. 

    HIRA stands for Hazard Identification and Risk Assessment.

    • HIRA is a systematic process for identifying potential hazards in the workplace and assessing the associated risks.

    • It helps in determining appropriate control measures to eliminate or reduce the risks to an acceptable level.

    • Examples of hazards that may be identified through HIRA include chemical exposure, fire hazards, and ergonomic risks.

  • Answered by AI

I applied via Recruitment Consulltant and was interviewed in Jun 2022. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Don’t add your photo or details such as gender, age, and address in your resume. These details do not add any value.
View all Resume tips
Round 2 - Aptitude Test 

My stady releted aal questions

Interview Preparation Tips

Topics to prepare for Creative Hands HR Consultancy Civil Engineer interview:
  • Civil Construction
  • Business Development
Interview preparation tips for other job seekers - Mehnat krte rhni chahiye saphalta jarur milegaa

I applied via Naukri.com and was interviewed in Feb 2022. There was 1 interview round.

Round 1 - HR 

(4 Questions)

  • Q1. What are your salary expectations?
  • Q2. Why should we hire you?
  • Q3. What are your strengths and weaknesses?
  • Q4. Tell me about yourself.

Interview Preparation Tips

Topics to prepare for Creative Hands HR Consultancy Civil Engineer interview:
  • Civil Engineering
Interview preparation tips for other job seekers - Market yourself. ...
Apply even if you're not fully qualified. ...
Job search like it's your job. ...
Use informational interviews to network. ...
Set yourself apart with letters of recommendation. ...
Know yourself and what you want. ...
Pump yourself up and stay positive.
Contribute & help others!
anonymous
You can choose to be anonymous

Sheltera Consultants Interview FAQs

What are the top questions asked in Sheltera Consultants Junior Engineer Civil interview?

Some of the top questions asked at the Sheltera Consultants Junior Engineer Civil interview -

  1. How to calculate material of M20 grade concrete? And ra...read more
  2. How to perform cement finesse test and final setting time and initial setting t...read more
  3. What is the Nominal mix and design mi...read more

Recently Viewed

SALARIES

HSBC Software Development

SALARIES

Hospaccx India

SALARIES

Multitech Engineers

LIST OF COMPANIES

Flamingo Pharmaceuticals

Locations

REVIEWS

Tata Elxsi

No Reviews

SALARIES

National Plastic Industries

INTERVIEWS

Vanan Online Services

No Interviews

SALARIES

4th Quarter Technologies

SALARIES

Romsons Group Of Industries

LIST OF COMPANIES

Sir Ganga Ram Hospital

Locations

Tell us how to improve this page.

Interview Questions from Similar Companies

Deloitte Interview Questions
3.8
 • 2.9k Interviews
PwC Interview Questions
3.4
 • 1.4k Interviews
Ernst & Young Interview Questions
3.4
 • 1.1k Interviews
KPMG India Interview Questions
3.5
 • 805 Interviews
Randstad Interview Questions
3.8
 • 259 Interviews
ABC Consultants Interview Questions
3.9
 • 186 Interviews
Grant Thornton Interview Questions
3.7
 • 100 Interviews
Protiviti Interview Questions
3.2
 • 56 Interviews
RSM India Interview Questions
3.4
 • 54 Interviews
View all

Sheltera Consultants Junior Engineer Civil Reviews and Ratings

based on 1 review

3.0/5

Rating in categories

3.0

Skill development

2.0

Work-life balance

2.0

Salary

1.0

Job security

1.0

Company culture

1.0

Promotions

1.0

Work satisfaction

Explore 1 Review and Rating
Civil Site Engineer
9 salaries
unlock blur

₹2.4 L/yr - ₹3 L/yr

Autocad Draughtsman Civil
8 salaries
unlock blur

₹1.2 L/yr - ₹3 L/yr

Structural Design Engineer
8 salaries
unlock blur

₹2.5 L/yr - ₹3.6 L/yr

Civil Engineer
7 salaries
unlock blur

₹1.7 L/yr - ₹6 L/yr

Draughtsman Civil
6 salaries
unlock blur

₹3 L/yr - ₹3.2 L/yr

Explore more salaries
Compare Sheltera Consultants with

KPMG India

3.5
Compare

PwC

3.4
Compare

Deloitte

3.8
Compare

Ernst & Young

3.4
Compare
Did you find this page helpful?
Yes No
write
Share an Interview