AmbitionBox
Interview Questions
- Reviews
- Salaries
- Interview Questions
- About Company
- Benefits
- Jobs
- Office Photos
- Community
Add office photos
Filter interviews by
Mahendra Sponge And Power Interview Questions, Process, and Tips
Top Mahendra Sponge And Power Interview Questions and Answers
- Q1. How many flag in 8085 microprocessor and it's name?asked in Maintenance Engineer interview
- Q2. How many pin in 8085 microprocessor?asked in Maintenance Engineer interview
- Q3. Full form of IC. What is KCL lowasked in Maintenance Engineer interview
Mahendra Sponge And Power Interview Experiences
2 interviews found
Anonymous
I applied via Campus Placement and was interviewed before Jan 2021. There were 3 interview rounds.
What is defferent between analog and digital?
(5 Questions)
- Q1. My Introduction in English
- Q2. Addition of binary numbers.
- Ans.
Binary addition involves adding two binary numbers digit by digit.
Start from the rightmost digit and add the corresponding digits of both numbers.
If the sum is 0 or 1, write it down. If it is 2, write down 0 and carry 1 to the next digit.
Repeat the process for all digits, including the carried digit from the previous step.
The final result is the sum of the two binary numbers.
Example: 1011 + 1101 = 11000
- Q3. How many pin in 8085 microprocessor?
- Ans.
The 8085 microprocessor has 40 pins.
The 8085 microprocessor has 40 pins in total.
These pins are used for various functions such as data transfer, address bus, control signals, power supply, and clock signals.
Some of the important pins include the ALE (Address Latch Enable), RD (Read), WR (Write), and RESET pins.
The pin configuration of the 8085 microprocessor is shown in its datasheet.
Understanding the pin configuratio...
- Q4. How many flag in 8085 microprocessor and it's name?
- Ans.
There are 5 flags in 8085 microprocessor - Carry, Auxiliary Carry, Sign, Zero, and Parity.
8085 microprocessor has 5 flags
Carry flag is set when there is a carry out of the MSB in an arithmetic operation
Auxiliary Carry flag is set when there is a carry out of bit 3 in an arithmetic operation
Sign flag is set when the result of an operation is negative
Zero flag is set when the result of an operation is zero
Parity flag is ...
- Q5. Full form of IC. What is KCL low
- Ans.
IC stands for Integrated Circuit. KCL low refers to Kirchhoff's Current Law.
IC is a small electronic device made up of multiple components on a single chip.
KCL low is a principle in electrical engineering that states that the sum of currents entering a node is equal to the sum of currents leaving the node.
ICs are commonly used in electronic devices such as computers, smartphones, and televisions.
KCL low is used to anal...
Interview Preparation Tips
Skills evaluated in this interview
Maintenance Engineer Interview Questions asked at other Companies
Selected
I applied via Walk-in and was interviewed before Aug 2022. There were 3 interview rounds.
(1 Question)
- Q1. Tell me some things about yourself.
(1 Question)
- Q1. Do you know. EHS RELATED JOB RESPONSIBILTY
Interview Preparation Tips
Top trending discussions
Interview questions from similar companies
I applied via Referral and was interviewed in Jun 2021. There were 3 interview rounds.
Interview Questionnaire
1 Question
- Q1. Substation erection
Interview Preparation Tips
Assistant Manager Interview Questions & Answers
Premier Energies
SOUMYA SUNDAR KHANRA
posted on 11 Mar 2025
Selected
I appeared for an interview before Mar 2024.
(2 Questions)
- Q1. Difference between differential pressure transmitter and transducer
- Ans.
Differential pressure transmitters measure pressure differences, while transducers convert physical quantities into signals.
Differential pressure transmitters measure the difference in pressure between two points, often used in flow measurement.
Transducers convert one form of energy into another, such as converting pressure into an electrical signal.
Example of a differential pressure transmitter: Used in HVAC systems t...
- Q2. How the pressure gauge working
- Ans.
A pressure gauge measures the pressure of gases or liquids in a system, providing critical data for monitoring and control.
Uses a sensing element (like a diaphragm) that deforms under pressure.
The deformation is converted into a readable value, often via a dial or digital display.
Common types include analog gauges (with a needle) and digital gauges (with electronic sensors).
Applications range from industrial machinery
(2 Questions)
- Q1. So long , can not explain
- Q2. All decided during technical round
Interview Preparation Tips
(2 Questions)
- Q1. About your self
- Q2. Project questions
(1 Question)
- Q1. What is the purpose of multimeter
- Ans.
A multimeter is a versatile tool used to measure voltage, current, and resistance in electrical circuits.
Measures voltage: Used to measure the potential difference between two points in a circuit.
Measures current: Used to measure the flow of electric charge in a circuit.
Measures resistance: Used to measure the opposition to the flow of electric current in a circuit.
Can also measure continuity, capacitance, and frequenc...
Interview Preparation Tips
Mahesh Malviya
Selected
I applied via Walk-in and was interviewed before Aug 2022. There were 2 interview rounds.
(2 Questions)
- Q1. Solar energy releted
- Q2. Manufacturing process of the printing line
- Ans.
The manufacturing process of the printing line involves various steps to produce printed materials efficiently.
Designing the layout of the printing line
Selecting the appropriate printing technology (e.g. offset, digital, flexography)
Calibrating and setting up the printing equipment
Testing the printing quality and making adjustments as needed
Implementing quality control measures throughout the process
Assistant Manager Interview Questions & Answers
Gupta Power Infrastructure
ARUN KUMAR TRIPATHY
posted on 25 Feb 2025
(1 Question)
- Q1. About your experience in past company
Interview Preparation Tips
Selected
I applied via Referral and was interviewed before Jan 2024. There were 2 interview rounds.
(1 Question)
- Q1. Questions related to my field
(1 Question)
- Q1. Salary discussion and
Interview Questionnaire
1 Question
- Q1. Debt equity ratio
Mahendra Sponge And Power Interview FAQs
Tell us how to improve this page.
Interview Questions for Popular Designations
- Senior Executive Interview Questions
- Associate Interview Questions
- Analyst Interview Questions
- Software Developer Interview Questions
- Business Analyst Interview Questions
- Sales Executive Interview Questions
- Graduate Engineer Trainee (Get) Interview Questions
- System Engineer Interview Questions
- Show more
Interview Questions from Similar Companies
Mahendra Sponge And Power Reviews and Ratings
based on 32 reviews
Rating in categories
|
Assistant Manager
10
salaries
|  ₹3.6 L/yr - ₹4.3 L/yr |
|
Accountant
9
salaries
| ₹2.8 L/yr - ₹3.7 L/yr |
|
Shift Incharge
6
salaries
| ₹2.4 L/yr - ₹4.2 L/yr |
|
Assistant Engineer
5
salaries
| ₹2.4 L/yr - ₹3 L/yr |
|
Mechanical Engineer
5
salaries
| ₹2.4 L/yr - ₹2.5 L/yr |
Sterlite Power
Doosan Power Systems
Inox Wind
Gupta Power Infrastructure
- Home >
- Interviews >
- Mahendra Sponge And Power Interview Questions
