10+ Linetech Interview Questions and Answers

It depends on the project and its priorities.

• If the project is time-sensitive, then time under budget is worse.

• If the project has a fixed deadline, then cost under budget is worse.

• If the project has both time and cost constraints, then it depends on which constraint is more critical.

• In general, it is better to have a balanced approach to managing both time and cost.

• It is important to communicate any deviations from the budget or timeline to stakeholders.

It depends on the project and its priorities.

• Cost over run may be acceptable if the project has a tight budget and the delay is not critical.

• Time over run may be acceptable if the project has a strict deadline and the additional cost can be managed.

• Both cost and time over runs should be avoided as they can impact the project's success and reputation.

• The decision should be based on a thorough analysis of the project's priorities and constraints.

• Effective planning and risk mana...read more

The slump in concrete grade m-40 is typically between 75mm to 125mm.

• Slump is a measure of the consistency or workability of concrete.

• For concrete grade m-40, the slump range is usually between 75mm to 125mm.

• Slump is determined by conducting a slump test, where a cone-shaped mold is filled with concrete and then removed to measure the slump.

• The slump value indicates the flow and compactness of the concrete mix.

• A higher slump value indicates a more workable and fluid concrete m...read more

I will analyze the reasons for the cost overrun and develop a plan to mitigate it.

• Identify the root cause of the cost overrun

• Review the project budget and timeline

• Develop a plan to reduce costs without compromising quality

• Communicate the situation to stakeholders and seek their input

• Implement the plan and monitor progress closely

Ring cutting length refers to the measurement of the length of a ring that needs to be cut.

• Ring cutting length is determined by measuring the circumference of the ring and dividing it by π (pi).

• The formula for calculating the ring cutting length is: L = C / π, where L is the cutting length and C is the circumference of the ring.

• For example, if the circumference of a ring is 10 cm, the cutting length would be approximately 3.18 cm.

To control deviation in vertically elements, proper leveling techniques and equipment must be used.

• Use a precise leveling instrument such as a digital level or an automatic level

• Ensure the instrument is properly calibrated before use

• Establish a benchmark or reference point for vertical control

• Use a leveling rod or staff to measure height differences accurately

• Perform regular checks and adjustments during the survey to maintain accuracy

• Consider factors like temperature, atmosp...read more

The construction cost was $10 million.

• The total cost of construction was $10 million.

• The cost included materials, labor, and equipment.

• The project was completed within budget.

• The cost was higher than anticipated due to unexpected delays.

• The cost was lower than expected due to efficient planning and management.

Cross checking column position in land surveying

• Cross check column position by comparing measurements from different surveying techniques

• Use multiple surveying instruments to verify column positions

• Compare measurements with existing reference points or benchmarks

• Ensure accuracy by repeating measurements and averaging the results

• Document and record all measurements and cross-checking steps for future reference

LPA stands for Lasting Power of Attorney, which is a legal document that allows a person to appoint someone to make decisions on their behalf. FAO refers to Foreign Account Operations, which involves managing financial accounts held outside one's home country.

• LPA is used in the context of appointing someone to act on behalf of an individual in case they become mentally incapacitated.

• FAO involves managing financial accounts held in foreign countries, often for individuals or b...read more

To control plastering thickness, proper preparation, use of guides, and regular measurements are essential.

• Ensure the surface is clean and free from debris before applying plaster.

• Use guides such as screeds or battens to maintain a consistent thickness.

• Regularly measure the thickness using a measuring tape or a thickness gauge.

• Adjust the amount of plaster applied based on the measurements to achieve the desired thickness.

• Take into account any variations in the substrate or sp...read more

LD reduces workability and increases the risk of cracking in high grade concrete.

• LD (Lignite Dust) is a fine powder that is added to concrete to improve workability.

• However, in high grade concrete, LD can reduce workability and increase the risk of cracking.

• This is because high grade concrete has a lower water-cement ratio, which means there is less water available to hydrate the cement and make the concrete workable.

• Adding LD to high grade concrete can further reduce the amo...read more

The number of bricks in 1 cubic meter varies depending on the size of the bricks used.

• The number of bricks in 1 cubic meter will depend on the size of the bricks being used.

• Standard size bricks (190mm x 90mm x 90mm) will have a different count compared to larger or smaller bricks.

• Calculations can be done by dividing the volume of 1 cubic meter by the volume of a single brick.