Filter interviews by
I applied via Recruitment Consulltant and was interviewed before Dec 2023. There was 1 interview round.
The stress-strain diagram of steel shows the relationship between stress (force applied) and strain (resulting deformation).
The diagram typically consists of a linear elastic region, a yield point, a plastic region, and a fracture point.
In the linear elastic region, stress and strain are directly proportional according to Hooke's Law.
The yield point is where the material begins to deform plastically.
The plastic region ...
Mechanical properties of materials include strength, stiffness, toughness, hardness, ductility, and elasticity.
Strength: Ability to withstand applied force without failure (e.g. tensile strength, compressive strength)
Stiffness: Resistance to deformation under load (e.g. Young's modulus)
Toughness: Ability to absorb energy and deform plastically before fracturing (e.g. impact toughness)
Hardness: Resistance to indentation...
The second law of thermodynamics states that the total entropy of an isolated system can never decrease over time.
Entropy in a closed system tends to increase over time
Heat naturally flows from hot to cold objects
Efficiency of energy conversion processes is limited by the second law of thermodynamics
I applied via Approached by Company and was interviewed before Feb 2022. There were 2 interview rounds.
Shell thickness calculation involves considering factors like material properties, pressure, and temperature.
Shell thickness calculation involves determining the minimum thickness required to withstand the pressure and temperature of the fluid inside the shell.
Factors to consider include material properties, pressure, temperature, and corrosion allowance.
Heat treatment process involves heating and cooling a material to...
Properties of material refer to its physical and chemical characteristics.
Physical properties include density, melting point, boiling point, and conductivity.
Chemical properties include reactivity, flammability, and toxicity.
Materials can also have mechanical properties such as strength, toughness, and elasticity.
Examples of materials and their properties include steel (high strength and hardness), aluminum (low densit...
Advance Valves Global interview questions for popular designations
I applied via Campus Placement and was interviewed before May 2021. There were 2 interview rounds.
List of manufacturing processes, casting defects, and welding defects.
Manufacturing processes: machining, forging, stamping, extrusion, injection molding, etc.
Casting defects: porosity, shrinkage, cold shuts, misruns, etc.
Welding defects: lack of fusion, porosity, cracks, undercutting, etc.
I was interviewed before Sep 2016.
Top trending discussions
Flow transmitter senses flow and transmits signal to controller in selected range.
Use a flow transmitter that is capable of sensing flow and transmitting a signal.
Connect the flow transmitter to the controller using appropriate wiring and communication protocols.
Configure the flow transmitter to operate within the desired range.
Ensure proper calibration of the flow transmitter to accurately measure and transmit flow da...
I applied via Campus Placement and was interviewed before Mar 2022. There were 4 interview rounds.
General Aptitude test of 50 questions, need to clear in 1 hour
Gear architecture refers to the design and layout of gears in a mechanical system.
Gear architecture involves determining the type of gears to be used, their size, shape, and arrangement.
It also includes considerations such as gear ratio, tooth profile, and material selection.
Examples of gear architectures include spur gears, helical gears, bevel gears, and worm gears.
Shear modulus is a measure of a material's stiffness in response to shear stress.
Shear modulus is also known as the modulus of rigidity.
It is defined as the ratio of shear stress to shear strain in a material.
Higher shear modulus indicates higher stiffness and resistance to deformation.
Common units for shear modulus are pascals (Pa) or gigapascals (GPa).
posted on 18 Mar 2023
I applied via Company Website and was interviewed in Apr 2022. There were 2 interview rounds.
Iron Carbon Diagram is a graphical representation of the phases of iron and carbon at different temperatures. Shaft calculations involve determining the dimensions and material properties of a shaft for a specific application.
Iron Carbon Diagram shows the phases of iron and carbon at different temperatures, helping in understanding the behavior of steel.
Shaft calculations involve determining the dimensions (diameter, l...
GD&T stands for Geometric Dimensioning and Tolerancing, a system for defining and communicating engineering tolerances.
GD&T is used to specify the allowable variations in form, size, and orientation of part features.
It uses symbols, such as concentricity, flatness, and perpendicularity, to communicate design requirements.
GD&T helps ensure that parts fit together properly and function as intended.
It is commonly used in ...
based on 2 interviews
Interview experience
based on 67 reviews
Rating in categories
Assistant Manager
34
salaries
| ₹0 L/yr - ₹0 L/yr |
Quality Engineer
13
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Design Engineer
13
salaries
| ₹0 L/yr - ₹0 L/yr |
Design Engineer
12
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Engineer Marketing
10
salaries
| ₹0 L/yr - ₹0 L/yr |
Forbes Marshall
Kirloskar Brothers
Ksb Pumps
Thermax Limited