Xilinx Design Engineer Interview Questions and Answers

Round: Resume Shortlist
Experience: Resume is not given any due importance in selection for further rounds . But honesty is very important as it counts once you are selected for HR round .
Tips: Try to be one hundred percent honest . And put your projects and course work in the beginning. They don't care your POR s and extra curricular activities.

Round: Test
Experience: Hardware - Questions are mainly from ELECTRICAL CIRCUITS (RLC ckts) , Analog ckts. Amplifiers , Opamps , digital system design . Aptitude section is very easy . Hardware section is tough .I felt Signal processing was easier , indeed I got selected for that profile .
Tips: Prepare thoroughly these courses :- EMC , DIGITAL SYSTEMS, NETWORKS AND SYSTEMS,ANALOG & DIGITAL SIGNAL PROCESSING , ANALOG CKTS COURSES .THAT SHOULD BE ENOUGH .
Duration: 90 - Signal Processing minutes
Total Questions: 120 - Hardware and aptitude

Round: Group Discussion
Experience: No
Tips: No

Duration: 2
College Name: IIT Madras

Round: Test
Experience: The selection procedure is a test followed by tech interview and an HR interview.
The test had two parts:
 Aptitude (common across all profiles)
 A tech. test (separate for each profile)

Round: Interview
Experience: The tech interview was the important one and the HR interview was just about knowing the student and vice-versa. The tech interview was more concentrated on the basics and more importance was given to the approach of solving the problem rather than solving the problem itself.
No CGPA cutoff.

Round: Interview
Experience: Not very important.

General Tips: The work is well structured and executed. There is a lot of opportunity for more technical learning. Interns are also included into the teams and this helps the intern on knowing about the things going around them and gets an overall view of how things work.
As a whole, the work is very good, and exceeds all the expectations of the students.
College Name: IIT Madras

Round: Technical Interview
Experience: They asked me about my thesis and some device related questions as my thesis was on modelling of device. Questions were basic and were related to variation of device parameters with environmental factors and other parameters. Apart from that, several questions related to basic digital circuits were also asked concerning flip flops, latches, setup time and hold time. The technical interview went on for approximately 1 hour.

Round: HR Interview
Experience: The HR round lasted for about 5 mins only. The HR person asked me whether I were interested in going for PhD or not and about my hobbies and interests. Overall, the interviewers are very friendly and asked basic questions only.
Tips: Prepare your CV well, have a good CPI, do your thesis sincerely, concentrate on your basics and you will stand a very good chance of getting selected.


General Tips: Do the courses thoroughly, make good course projects and start preparing for the placement session at least 1 month early.

Don’t ever mention to them that you are interested in higher studies even if you are applying. In case you don’t get a job at your targeted company, don’t lose hope and move on to the next one.

Concentrate on your preparation and the things that are of utmost importance, don’t get bogged down by pressure. Be optimistic and cheerful, because confidence really helps during interviews.

Final Tips :
1. Be confident and enthusiastic in your response to questions because you have to make them understand that you are interested in the profile.
2. Chalk out a plan to strengthen your strong points and address the weak ones.

College Name: IIT Kanpur

Round: Test
Experience: A written test with Core - Essay Type Questions.
Tips: Revise previous core VLSI courses (Digital Circuits, Digital IC Design, Analog Circuits, and Solid State Devices).
Duration: 60 minutes

Round: Interview
Experience: 3 rounds of interviews (15-20 minutes each)Basic digital concepts, ability to analyze a given circuit
Tips: Be thorough with your basic electronics conceptsPerformance in the technical interview counts a lotAnalog devices didn't need any particular course or project, they mainly look for strong basics in digital/analog circuit theory, and ability to analyzeRevise all of your core courses, starting from the basics

Round: Interview
Experience: For the HR round, questions about your background, family, interests etc. are asked

General Tips: Learn to keep cool, even under stress, and have confidence on your knowledge
College Name: IIT Madras

Round: Test
Duration: 60 minutes

Round: HR Interview
Experience: No prep required for HR round, asked few personal questions (about your background, family, interests etc.)

General Tips: Revise all of your core courses, starting from the basics. Junta usually stumble when asked questions from basic fundaes.
I felt a lot of stress before my first interview, which affected my performance badly. Learn to keep cool, and have confidence on your knowledge.
Skill Tips: You should have ability to analyse a given circuit
Skills: Digital electronics basics,
College Name: IIT MADRAS

Round: Technical Interview
Experience: I was unable to solve the problem properly but after that he gave me a normal k map to solve.

Round: Technical Interview
Experience: Asked about inverter and delay dependency on temperature and other parameters

Round: Technical Interview
Experience: I managed to answer most of the answer that i did wrong since i had discussed it with my friends after coming from college.

Round: HR Interview
Experience: provided answers that relates company requirements

Round: HR Interview
Experience: Listened carefully about their job description and work environment

College Name: IIT Madras

Interview preparation tips for other job seekers - don't try to elaborate the answer be precise and clear about your answers.