Wilo Mather and Platt Pumps FEA Engineer Interview Questions and Answers

Q1. GD & T symbols and it's uses
Ans. 
GD&T symbols are used in engineering to communicate design specifications and tolerances.
• GD&T symbols are used to specify geometric dimensions and tolerances on engineering drawings.

• They help ensure that parts are manufactured to the correct dimensions and fit together properly.

• Examples of GD&T symbols include concentricity, perpendicularity, and flatness.

• GD&T symbols are often used in conjunction with traditional dime
Answered by AI
Add your answer
Q2. Stress strain and it's curve heat treatment process
Ans. 
Stress-strain curve is a graphical representation of the relationship between stress and strain in a material during a mechanical test.
• Stress-strain curve shows how a material deforms under load.

• It consists of elastic, plastic, and fracture regions.

• Heat treatment process involves heating and cooling a material to alter its properties.

• Heat treatment can change the microstructure of a material, affecting its mechanical p...read more
Answered by AI
Add your answer

Q1. Salery discussion
Add your answer

Q1. Based on canditate experience
Add your answer

Q1. Creo tool test is given
Add your answer

Q1. Salary discussion, comapny overview
Add your answer

Q1. Tool test on catia v5 3d modelling
Add your answer

Q1. Tell about gears or transmission
Ans. 
Gears or transmission are mechanical components used to transfer power from one part of a machine to another.
• Gears are toothed wheels that mesh together to transmit motion and power.

• They can change the speed, torque, and direction of a power source.

• Types of gears include spur gears, helical gears, bevel gears, and worm gears.

• Transmissions are systems that use gears to control the power and speed of a vehicle.

• They can b...read more
Answered by AI
Add your answer
Q2. Draw a simply supported beam
Ans. 
A simply supported beam is a beam supported at both ends with no moment resistance.
• Draw a straight horizontal line to represent the beam

• Add two vertical lines at each end to represent the supports

• Label the supports as 'A' and 'B'

• You can add a distributed load or point load for additional detail
Answered by AI
Add your answer

Q1. Tell me about yourself GD&T CATIA V5 compisute module. Blade nonenclatures
Add your answer

Q1. Nothing simple technical questions related to RTM
Add your answer
Q2. Nothing simple questions about vb
Add your answer

Q1. Gas seal system
Add your answer

Questions on logical and quants

Q1. What is Bernoulli principle?
Ans. 
Bernoulli principle states that an increase in the speed of a fluid occurs simultaneously with a decrease in pressure or a decrease in the fluid's potential energy.
• States that as the speed of a fluid increases, its pressure decreases

• Used to explain lift in airplane wings

• Applies to various fluid dynamics situations such as flow through pipes
Answered by AI
Add your answer
Q2. What is stress and how it can be measured?
Ans. 
Stress is a force acting on a material that causes deformation. It can be measured using techniques like strain gauges and load cells.
• Stress is a measure of the internal forces within a material resisting deformation.

• It is typically measured in units of force per unit area, such as Pascals or pounds per square inch.

• Common methods of measuring stress include strain gauges, load cells, and extensometers.

• Stress can be cat...read more
Answered by AI
Add your answer

Questions from transducer digital electronics

Q1. Explain your project
Add your answer

Q1. I didn't selected for HR round
Add your answer

Q1. Technical round with the team lead. Test your basic knowledge on engineering/project handling abilities.
Add your answer

Q1. Technical Round with Group lead manager. Might takes an hour. Pure technical questions based on your past experience/projects you worked on. How you approached or handled the projects individually or as a ...read more
Add your answer

Q1. Kind of one on one discussion with you and the Executive lead (Head of the department). Questions will be mostly on behavioral, sutiation based questions ect..
Add your answer

Q1. Predominantly on Salary negotiations and document verification
Add your answer